Projection, Power indicator lamp | Panasonic PT-D10000E guide

Projection

Power indicator lamp

Power indicator lamp

This shows the power supply status. Make sure that you fully understand the operation of the power indicator lamp before operating the projector.

Indicator			Projector status
status			Projector status
status
Off			Main power is off
			Standby mode
Red		Lit	POWER ON () button can be pressed
			so that images can be projected.
Green		Lit	Images are being projected (on)
			Standby preparation mode
Orange		Lit	After a short while, the projector will
			switch to standby mode.

Attention

•While the projector is in standby preparation mode (when the power indicator lamp is lit orange), the internal fan is running to cool down the projector. Do not turn off the MAIN POWER switch or disconnect the power cord at this time.

Note

•If the POWER ON “ ” button is pressed while the projector is still in standby preparation mode, it may take some time before the projector is ready to project pictures.

•The cooling fan will still be operating and the projector will still be drawing approximately 25 W of power while the projector is in standby mode (when the power indicator lamp is lit red).

Connecting the power cord

Insert the accessory power cord securely into the projector and the electrical outlet.

Be sure to read the “IMPORTANT SAFETY NOTICE” (pp. 4-5) and “Precautions with regard to safety” (pp. 6-9) for details on handling the power cord.

■Installation

1. Check the shape of the AC IN terminal on the side of the projector and the shape of the power cord connector, and insert the power cord securely into the AC IN terminal.

2. Insert the power cord plug into an electrical outlet.

■ Removal

1.Check that the MAIN POWER switch on the projector is at the OFF position, and then disconnect the power cord plug from the electrical outlet.

2.Disconnect the power cord connector from the AC IN terminal of the projector.

Attention

34 – ENGLISH

•Connect all peripheral equipment to the projector before connecting the projector’s power cord. (pp. 25-26)

Image 34

Panasonic PT-D10000E, PT-DW10000E manual Projection, Power indicator lamp, Connecting the power cord, Installation

Contents

PT-DW10000E Models No. PT-D10000E Model number PT-D10000E/PT-DW10000E Dear Panasonic CustomerSerial number Contents Important Safety Notice Getting Started Important the Moulded Plug U.K. onlyFuse Insert the power cord plug securely into the wall outlet Precautions with regard to safetyDo not handle the power cord plug with wet hands Do not overload the wall outlet Do not disassemble the lamp unit Insulate the battery using tape or similar before disposalDo not place the projector into water or let it become wet Do not place liquid containers on top of the projector Do not place any heavy objects on top of the projector Use only the specified batteryAlways disconnect all cables before moving the projector Do not look into the lens while the projector is being used Getting Started Before Using Accessories To view clear images MaintenanceDisposal Screen Location and function of each part Remote control unitFront Side Top Bottom Rear Projector Main UnitLamp LAMP1, LAMP2, LAMP3, LAMP4 Power Standby Side Controls Connection terminals Effective range of remote control operation Using the remote control unitLoading batteries Setting projector ID number to remote control Using a wired remote control Installation Examples of system expansion Installation geometry Adjusting the feetProjection scheme Getting StartedSide View Top View Installation Calculation formulas for projection distance by lens types Before starting connection Pin SignalConnection Pin No Example of connecting with Video devices Control PC Video deck TBC built-in Control PC To 2nd projector Serial in terminal Example of connecting with personal computersControl PC Module Module model Terminal Signal formats supported Installation of input module optionalInstalling the input module Types of the input modules optional Remove the slot cover Procedure of installationFix the input module Register the input signal Insert the input module Business digital Connecting signals to the input moduleSignal Projector High-vision DVI-D input module ET-MD77SD1 for 480i/576i Connecting the signal to the SD-SDI input moduleSD-SDI input module optional LAN terminal*1 ET-MD77SD3 for HD/SD Connecting the signal to the HD/SD-SDI input moduleHD/SD-SDI input module optional LAN terminal *1 Connecting signals to the DVI-D input module DVI-D input module optional Projection lens cover lock button How to install the projection lensHow to remove the projection lens Projection lens lock button Installation Power indicator lampConnecting the power cord Indicator Projector status Status Press Power on Powering up the projectorMaking adjustment and selection # $ Press the marked side Powering off the projector# Press Power Standby Confirmation screen will appear How to adjust the lens How to adjust the focus, zoom and shift Moving the projection lens position to the home position Adjustment range after lens position optical shiftModel number PT-D10000E PT-DW10000E Projection lens Automatic adjustment Auto Setup Press Enter Registration of input signal dataRegistration of new data Press to display Basic Clearing the data of registered signalsSub memory Enter Press on normal screen Press to select the SUBRestrictions On-screen display function Switching the input signalBasic Operation Using the Shutter function Status function Turning on button illumination Automatic adjustmentUsing the FUNC1 button Displaying the internal test pattern Setting will change as follows each time Aspect is pressed Press Aspect on the remote controlChanging the picture aspect ratio On-screen menus Main Menu item Advanced Menu pp Test Pattern p Signal List pp Network ppPosition pp Display Language p Using the menu screens Resetting to the factory default Press to switch Picture Adjusting the pictureSwitching the picture mode Press to select Picture Adjusting Brightness Adjusting ContrastAdjusting Colour Adjusting the colour temperature Adjusting TintTemp Gamma setting Sharpness settingSharpness Reduction Noise reduction settingDynamic iris setting Iris Setting the system format Selector Display the Picture screen. p Press to select Picture RGB1/RGB2/DVI-D terminal input signalsSRGB is only enable when RGB signals are being input Press to select Natural Press to select Color Adjustment Adjusting the positionShift adjustment Press to select Shift Operation Adjusting the aspect ratioPress to switch Aspect Press to select Aspect Phase Adjusting the zoom ratioClock phase adjustment Interlocked Keystone Press to adjustKeystonedistortion correction Keystone screen will be displayed Digital cinema reality How to use Advanced MenuPress to switch Digital Press to select Digital Press to select Blanking Blanking adjustmentPress to select Input Resolution Press to select Total Edge blending adjustment Adjusting the clamp positionBlending Adjust Press to switch Frame Frame delayPress to select Frame Delay Delay Press to select Raster Position Press to adjust the position PT-D10000ERaster position PT-DW10000E Press to select the desired language Setting the Display LanguageChanging the display language Display Language Basic Operation Special Features Option1 settingsAdjusting colour matching Press to switch Color Matching Adjusting the colour Matching using a colorimeter Data Press to switch LargeLarge Screen Correction Press to select R, G, B or Cy, Mg, Ye, Wh Press Enter Signal Auto signalAutomatic adjustment Only RGB input Setup Back Colour Color Press to select AUX DVI Press to switch AUX DVIPress to switch P in P Edid Press to switch FUNC1 Setting FUNC1Press to select FUNC1 Position Position of on-screen indicationsOSD memory Memory Projector ID Option2 settingsSetting a projector ID Press Menu twice Altitude Installation SettingInstallation Press to select Altitude Press to select Output ResolutionDirection Horizontal Press to select Lamp Press to switch LampLamp select Select Lamp relay RS-232C settingRelay Cleaning System information Cleaning the air filterInformation Time Setting the date and timePress to select Date Clock Press to switch Startup Setting the startup logoPassword Press to select Startup Cycle of displayed internal test patterns Displaying the internal test patternTest pattern Pattern How to use network function Initial setting of network function Hold down Default for 3 seconds Press to select Store LAN terminal 10BASE-T/100BASE-TX Network connectionsName and function of network function parts LAN LINK/ACT lamp green Press OK and the top page will appear Password change Accessing from the Web browserClick Change password Basic control Monitor information Lens adjustment Test pattern displayDetail control Menu display Error information When Failed has appeared for an item Mail setup English Special DNS server set upButton to update settingsFeatures Numbers 0 9, period Authentication server setting Ping test Contents of mail sent Adjust clock Network config Firmware update PJLink security authorization Using the PJLink protocolSupported commands Command Control details Password Setting the securitySetting the password Displaying the security screen Password Change Setting the textChanging the password Press to set the password Change Changing the textPress to select Text Text screen will be displayed Communication conditions Factory setting Using the serial terminalsExamples of connection For RS-422 Pin assignments and signal namesPin Signal Description No. name Sub 9-pin male Basic format Control commandsCommand Function of command Remarks Accepted Projector Computer DTE Specifications Cable specifications1st 2nd RS-422 OUT Pin assignments and control Using the Remote 2 terminalExample of a control panel layout Names of terminals Open H Short L Lamp 1 monitor Lamp Indication of monitor lampLamp 3 monitor Lamp Place the filter cleaning unit Cleaning and replacement of air filterProcedure of cleaning Use a vacuum cleaner to remove any dust blockages Install the brush cover so that it Timing of lamp unit replacement Replacement of lamp unitPrecautions on lamp unit replacement Indication after 1 800 hours Procedure of lamp unit replacement Lamp unit cover Eye bolt Wire Installation procedureEye bolt Remote control does not Symptoms Check pointPower does not turn on No image appears on screen Self-diagnosis display Self Details Remedy Diagnosis Display FE1 Specifications Model No PT-D10000E PT-DW10000E RGB2 input Compatible RGB/YPBPR/DVI-D Signals Appendix List of P in P Main window Outside dimensions DimensionsInstallation dimensions diagram Adjusting colour matching Index Trademark Acknowledgement For business users in the European Union