Paradyne 3800 manual

Index

Reset, 10-2

Reset and Load Active (Z), 14-7 Reset Security, 12-10

Result Codes Enable/Disable, 9-17 enable/disable, 14-5 extended, 14-6 format, 14-6

list, B-1

Result Codes Format, 9-18

retrain, 2W Leased Line Signal Quality, 9-29 rings before answer, 14-15

RS366A status, 7-4 RTS Action, 9-11, 14-10 RTS/CTS Delay, 9-12, 9-13 RTS/CTS Delay (S26), 14-17

S

S–registers, 14-15 change, 14-5 display, 14-5 format, 14-15

S0 (Auto-Answer Ring Number), 9-20, 14-15 S2 (AT Escape Character), 9-16, 14-15

S3 (Carriage Return Character), 9-16, 14-15 S4 (Line Feed Character), 9-17, 14-16

S5 (Backspace Character), 9-17, 14-16 S6 (Blind Dial Pause), 9-21, 14-16

S7 (No Answer Timeout), 9-21, 14-16 S8 (“,” Pause Time), 9-21, 14-16

S10 (No Carrier Disconnect), 9-23, 14-16 S12 (Escape Guard Time), 9-16, 14-16 S18 (Test Timeout), 9-39, 14-17

S26 (RTS/CTS Delay), 9-12, 14-17

S34 (1800 Hz Training Tone), 14-17

S35 (Auto Redial, Leased Line), 9-31, 14-17 S36 (Rate Auto Originate), 9-31, 14-18 S37 (Auto Redial, DTR), 9-24, 14-18

S38 (DTR Cont Repeat), 9-19, 14-18

S39 (Receive Buffer Disconnect Delay), 9-38, 14-19 S40 (Auto Make Busy), 9-24, 14-19

S41 (Dial Line Rate), 9-25, 14-19

S43 (V.32bis Train), 9-27, 14-19

S44 (Leased Line Rate), 9-28, 14-20

S45 (Leased Line Transmit Level), 9-29, 14-20 S46 (Bad Lines Auto Originate), 9-30, 14-20 S47 (Auto Dial Standby), 9-32, 14-20

S48 (Leased–Line Carrier On Level), 9-32, 14-21

S49 (Transmit Buffer Disconnect Delay), 9-37, 14-21 S51 (DTE Remote Loopback), 9-39, 14-21

S52 (DTE Local Loopback), 9-39, 14-21 S53 (V.54 Address), 9-40, 14-21

S54 (V.54 Device Type), 9-40, 14-21

S55 (Access from Remote), 9-42, 14-22 S56–S59 (Remote Access Password), 9-42, 14-22 S61 (CT111 Rate Control), 9-14, 14-22

S62 (V.25bis Coding), 9-18, 14-22

S63 (V.25bis Idle Character), 9-18, 14-22

S64 (V.25bis New Line Character), 9-19, 14-23 S65 (Line Current Disconnect), 9-22, 14-23

S66 (NMS Call Messages), 9-43, 14-23

S67 (Directory Location 1 Callback), 9-42, 14-23 S69 (Make Busy Via DTR), 9-24, 14-23

S74 (Network Position Identifier), 9-44, 14-23 S75 (Network Management Address), 9-43, 14-24 S76 (V.32bis Autorate), 9-26, 14-24

S77 (DTR Alarm Reporting), 9-43, 14-24 S78 (V.32bis Automode), 9-25, 14-24

S80 (No Data Disconnect Trigger Signal), 9-23,

14-24

S81 (2W SQ Retrain), 14-25

S82 (V.32bis Autorate), 9-29, 14-25

S84 (AT Command Mode), 9-18, 14-25 S85 (Fast Disconnect), 9-22, 14-25

S88 (Straps When Disconnected), 9-41, 14-25

S89 (V.42 ARQ Window Size Increase), 14-26 S90 (DTE Rate = VF Rate), 9-14, 14-26

S91 (Cellular Enhancements), 9-38, 14-26 S92 (V.29 Train On Data), 9-32, 14-26

S93 (Cellular RJ11 Adapt), 9-44, 14-26 save

configuration options, 14-11 telephone numbers, 14-11

SDCP (Shared Diagnostic Control Panel), 3-1 SDU (Shared Diagnostic Unit), 3-1 secondary channel, 11-2

Security branch, 12-4

Security configuration options, 9-45 security messages, 4-12

Self (Test branch), 8-2 self-test, 8-2

Send Break Control, 9-37 serial number, 14-5 Service Line, 10-3

Set Access Control, 12-5

Set Administrative Password, 12-10 Set Answer Security, 12-8

Set Originate Security, 12-9 setting factory defaults, 4-13 Speaker Control, 9-41, 10-2 Speaker On/Off (M), 14-5 Speaker Volume, 9-42 Speaker Volume (L), 14-5 status, 4-8

Status branch, 7-2 status indicators, 4-4 Stop Bits, 9-9

Store Telephone Numbers (&Z), 14-11 Straps When Disconnected, 9-41 Straps When Disconnected (S88), 14-25 Sync Mode (&M, &Q), 14-10

3810-A2-GB30-30 September 1998 Index-5