Electrical System | Quinny 65040-AB guide

Section II - Description

The Power$ync II™ controller allows the customer to select Auto Dual as an alternate control method. Auto Dual incorporates a timer which will turn the compressor off if it remains in the unloaded condition for a preset length of time. If the system pressure remains above the preset pressure for the programmed time interval, Power$ync II™ places the compressor in Standby Mode, with the drive and fan motors de-energized. The Power$ync II™ controller waits for an indication of demand, recognized as a drop in system pressure to a preset minimum pressure level, and automatically restarts the compressor.

Essentially equal to Continuous Run, Auto Dual goes a step beyond to offer the opportunity for additional power savings in a system with more dramatic differences in demand. As demand changes with shift changes or varying operations, the Power$ync II™ controller will allow the QSD™ compressor to go into Standby Mode when compressor output is not needed. Like the Continuous Run Mode, a properly sized air receiver will ensure that the compressor operates and reacts properly as air system demand changes.

NOTE

Refer to section VIII for Power$ync II™ operating instructions.

Electrical System

A diagram of the electrical system is shown in the parts manual shipped with the compressor. A wiring diagram is also included in the control panel of all Quincy compressors.

NOTE

Due to continuing product improvements and updates, it is suggested that the wiring diagram included in the control panel be used when servicing the electrical control.

NOTE

Standard drive motors are open, drip-proof, with a maximum ambient temperature rating of 40°C. They are not suitable for salt laden, corrosive, dirty, wet or explosive environments.

The standard QSD™ compressor utilizes 460V incoming power through an across the line magnetic starter. A transformer in the control panel reduces this voltage to 120 VAC for the various controls on the unit. These controls include the selector switch, pressure switch, timer, high air temperature (HAT) safety switches, solenoid valve and various indicator lights. Other incoming line voltages are available as options. A NEMA 4 electrical enclosure is standard.

12	Quincy Compressor® - QSD™

Image 14

Quinny 65040-AB manual Electrical System

Contents

QSD Series Page Table of Contents Section V Maintenance or Service Preparation Standard Warranty Dimensional Data air-cooled Dimensional Data water-cooled Safety Precautions Section I General Safety Alert Symbols Spare Parts Ordering Information Section II Description General Description Compression Cycle and Air Flow Moisture Separator Cooling SystemLubricating Fluid System Water-cooled Capacity Control System Electrical System Back-up Control Shutdown Conditions Main Power on Light IndicatorsSafety Sensors High Discharge Air Temperature Lights Section II Description Receiving Section III InstallationMoving the Unit to the Installation Site Location Piping Connections Manual Shutoff Valve Piping Fit-up Electrical Guards Water Flow Water Quality Fluid Level Fan Rotation Starting the Compressor Section IV Operating ProceduresPrior to Starting Stopping the Compressor Normal Operation Stopping the Compressor Emergency Temperature Readings Water-cooledPressure Readings Section V Preparing for Maintenance or Service This page Intentionally Left Blank Section VI Servicing SafetyFluid Specifications Air Filter Fluid Life Preparation for New Seal Installation Input Shaft Seal Seal Installation Airend Sealing System Pressure Switch Back-up Operating Mode Section VII Service AdjustmentsPressure Switch Adjusting Pressure Switch This page Intentionally Left Blank Back-up Mode Operation Section Viii Power$ync II OperationIntroduction to Power$ync Do not switch modes with power on the compressor Single Machine Operational Modes Multiple Machine Operational ModeAuto Dual Time Delay Continuous Run Pressure Settings Network Load Delay Time Network Installation Connecting Cable to the Power$ync II Circuit Board Rocker Switch Settings UP/DOWN DEADBAND, F1 EDIT, Enter Return Network Voltage Tests on Power$ync II SystemsNetwork Setup Power-up Displays Start-up Section Viii Power$ync II Operation Compressor in Back-up Mode U19 Memory Failure Contact Your Service Representative U19 Data not Initialized Press F2 to Initialize Deadband Data Error Press F1 to ClearU19 Data Checksum Error Press F2 to Update Filter Needs Servicing Please Replace AS Soon AS Possible Additional Sensors Start-up DisplaysOperational Displays Compressor is Starting Programmed Shutdown Compressor is Unloaded Minutes Left to ShutdownCompressor is Unloaded Compressor Mode of Operation Auto Dual Timed Stop Press F1 Compressor Settings and Maintenance DisplaysMode and Pressure Displays Press F2 Read Pressure Settings pages 34-35 before Press F1 to change the load and unload pressures Machine ID for this Compressor Press Enter to Accept Value Machine ID SetupPlease Wait Network Configuration in Progress UP/DOWN POSITION, F1 EDIT, Enter Return Before setting or changing a sequence, readSequence Network Data UP/DOWN Machine ID, Enter Return DAY Monday SEQ Network Configuration MenuDAY Monday SEQ Abcd To clear a particular sequence from the memory, press F1 Compressor Hourmeter Menu Compressor Hourmeters Filter Service HourmetersReset Service Hourmeters Intake Filter Hours Press F1 to Reset Fluid Hours Press Enter to Return Press F1 to Reset Fluid Filter Hours Press Enter to ReturnFluid Filter Hours Reset to Press Enter to Return Fluid Hours Reset to Press Enter to Return To SET Time and Date Compressor Maintenance Menu Compressor Control TestTime Menu To View Current Time Time and Date Menu Current Time on this Control Unload Press HorsepowerCompressor Control Test Menu Unload Valve Test Press F1 Fluid Press Compressor Diagnostic Menu View Shutdown LOG Unit Configuration DateModem Baud Rate Setup Network Diagnostic Section Viii Power$ync II Operation ETOL00 FTOL00 Network Connection Data Confidence F1 to EDIT/ENTER to Accept Value Indicator is lit, the indicator will remain litModem INITIALIZATION** Init Compressor has Shut Down Emergency Stop Button WAS Pressed Sequence Data Error Press F1 to Clear Schedule Data Error Compressor has Shut Down Take Corrective Action Back-up Mode until all faults have been corrected Inlet Temp Fluid Pressure STG 1 OUT Temp STG 2 in Temp Shutdown Log Messages Emergency Stop Pressed Motor Overload STG 2 Discharge RTD Failure Control log has no entries at that point Section IX Troubleshooting Probable Causes Corrective Action Failure to Start Section IX Troubleshooting Unscheduled Shutdown Probable Causes Corrective Action Unscheduled Shutdown Probable Causes Corrective Action Low Air Delivery Frequent Air Cleaner CloggingHigh Discharge Air Temperature Frequent Fluid Filter Clogging Compressor does not Unload when there is no Air Demand Too Rapid Cycling Between Load and Unload Water in Buffing Air Vent Bowls Pressure Relief Valve ExhaustingExcessive Fluid in Buffing Air Vent Bowls Excessive Fluid in Gearbox Vent Bowl Low Delivery Pressure High Interstage Pressure Erroneous Displays Microprocessor Will Not Display Messages Section X- Maintenance Schedule Interval Action Daily Operating Record Quincy Compressor QSD Quincy Compressor QSD