AC Power Connection, DC Power Connection | RAD Data comm LRS-24

LRS-24Installation and Operation Manual	Chapter 2 Installation and Setup

AC Power Connection

➤To connect LRS-24 to AC power:

1.Check that the switch on the PS is set to OFF.

2.Use the 5-ft. (1.5m) standard power cable terminated by a standard 3-prong plug to connect AC power to the LRS-24.

3.Connect the power cable to the connector on the panel of LRSI-PSP/230/115 interface module.

4.Connect to the mains outlet.

5.Turn the POWER switch to ON to initiate the LRS-24.

DC Power Connection

➤To connect LRS-24 to DC power:

Note

Note

1.Connect the power cable between the DC distribution panel and the DC power connector of the LRSI-PSP/48 interface module.

2.Check that you have correct polarity.

DC power supply interface modules do not have power switches. Therefore, the DC power supply will start operating when DC power is applied.

To avoid turning on LRS-24 when connecting the power cables, use an external circuit breaker located near LRS-24 to control the supply of DC power, and protect the DC input line. Set the circuit breaker to OFF before connecting the DC power cable to LRS-24.

When redundant power supplies are used, it is recommended to connect the power cables to outlets powered by different circuits.

Connection of External Phantom Feed Voltage

An external power supply unit is necessary to supply external feed voltages. HTU-E1C/P, etc. require phantom feed voltage.

The recommended source for external voltages is LRS-PS-FEED, offered by RAD. LRS-PS-FEED is a standalone unit, intended for rack mounting (refer to Appendix B). To minimize cable runs, install LRS-PS-FEED directly above LRS-24 (leave 1U free space between LRS-24 and the LRS-PS-FEED). In this situation, connect the output cable of the LRS-PS-FEED (supplied with the LRS-PS-FEED unit) to the PHANTOM connector of the LRSI-PSP/48 or LRSI-PSP/230/115 interface module.

Interfaces and Connections

2-25

Order from: Cutter Networks

Ph:727-398-5252/Fax:727-397-9610

www.bestdatasource.com

Image 53

RAD Data comm LRS-24 operation manual AC Power Connection, DC Power Connection, Connection of External Phantom Feed Voltage

Contents

RAD Data Communications Headquarters US East US West LRS-24 Order from Cutter Networks Ph727-398-5252/Fax727-397-9610 Warranty Ports Safety Status Safety Warnings Regulatory Information Supplementary Information Safety To turn the power on Power-OnLRS-24 with CM-1 Module Normal Indications LRS-24 with CM-2 Module Preliminary Configuration Contents Management via the CM-2 Module Troubleshooting and DiagnosticsManagement via the CM-1 Module Module CM-2 Front Panel List of Figures List of Tables CM-2 Module Station CLK Connector, Pin Allocation General Overview Management/CM-2 functions Application Power SuppliesVersions Management of Local and Remote Distribution Nodes Features Remote Management Clock Power SuppliesRADview-HPOV Snmp Management System RADview-PC/MDM Management System Chassis Description Physical Description LRS-24B 3-D View LRS-24B Enclosure LRS-24F Enclosure 5shows a 3-dimensional view of LRS-24F Front View LRS-24 Module Slots Functional Description Power Supply PS Modules Common Logic Modules CM-2 Management Capabilities ManagementCM-1 Management Capabilities Number Technical SpecificationsUser Modules Functionality Word format software-configurableModules Data rates up to 9.6 kbps Temperature Humidity Up to 90%, non-condensing Operating Temperature StorageHardware To 113 F / 0 C to 45 C Skilled technician who is aware of the hazards involved IntroductionMechanical Data LRS-24F Mechanical Diagram LRS-24B Mechanical Diagram DC Power AC PowerInterface Module Handling Precautions Site Requirements and Prerequisites Unpacking the Chassis Module Handling PrecautionsFront Clearance Ambient Requirements PS Modules Installation and SetupFront Panels Before removing it from the enclosure Fuses PS Modules, Front Panel Indicators To install the first PS module PS Module InstallationAn AC and a DC PS module can be installed at the same time CM-1 Module Function Module CM-1, Front Panel Components Module CM-1, Internal Jumpers Internal Jumpers Module CM-1 Jumper Settings CM-2 Module CM-1 Installation ProcedureTo install CM-1 Module CM-2, Front Panel Indicator Function Module CM-2, Internal Jumpers Module CM-2 Jumper Settings CM-2 InstallationTo install CM-2 Interfaces and Connections PS Interface Module Types PS Interface Modules To install the PS interface module Interface Module InstallationInterface Module Front Panel Typical LRSI-F-CM1 module front panel is shown in Figure LRSI-F-1-CM2 10BT / LRSI-B-1-CM2 Front Panel To install LRSI-F-CM1 Interface moduleLRSI-F-1-CM2 / LRSI-B-1-CM2 Interface Modules with 10BaseT Color Indication Module panel includes two connectorsManagement 10BT Ethernet LEDs JP8 LRSI-F-1-CM2 Internal Settings LRSI-F-1-CM2 Module Jumper Settings LRSI-F-1-CM2 InstallationTo install LRSI-F-1-CM2 LRSI-F-2-CM2 Interface Module with 10Base2 12. LRSI-F-2-CM2 Interface Module Panel with 10B2 LRSI-F-2-CM2 Internal Settings Jumpers Controls Settings/Options LRSI-F-2-CM2 Interface Module Jumper Settings LRS-24 Enclosure DC Power Connection AC Power ConnectionTo connect LRS-24 to AC power To connect LRS-24 to DC power Management Connections Dry Contact Alarm ConnectionsStation Clock Connections Initial Operation and Basic Checks Power OnLRS-24 with CM-1 Module Connection to I/O User Modules Troubleshooting Power OffLRS-24 with CM-2 Module To turn off LRS-24 CM-1 To turn off LRS-24 with CM-2 Installation and Setup Management Capabilities CM-1 Functions Management RS-232 Port Interface Characteristics Terminal CharacteristicsConnecting the Terminal Default data rate 38.4 kbps Connection through Modem Link Direct Connection of Supervision Terminal Operating the CM-1 Supervision Terminal Configuring the TerminalSelect the full-duplex mode Turn off the terminal echo Configuring Individual Modules Performing Preliminary ConfigurationTo configure each module Module is installed Management via the CM-1 Module CM-2 Module Capabilities Chapter Management via the CM-2 Module CM-2 Functions Handling of Management Communication Management Priorities Preliminary Configuration Activities Preliminary Configuration of Other Modules Preliminary Configuration of CM-2 moduleInitializing CM-2 Modules with Internal Snmp Agent Modules without Internal Agent Replacement of CM-2 module if a CM-2 module is plugged into Terminal Connection Methods RS-232 Supervisory Port Interface CharacteristicsConnection of Management Station Connection of Supervision Terminal LRS-24 Typical Connection of Supervision Terminal Through Slip Typical Connection to Network Management Station Command Protocol Command Language SyntaxFor a complete description of each command, see Appendix D CM-2 Supervision Terminal Language Command Function/Action Index of CommandsErrors Execution Supervision Terminal Operating Instructions Terminal Command Set Index for CM-2 Module Factory set password is radlrs Changing the PasswordTo change the password Type Node 13 DEF PWD Enter Password Menu Screen appears see Figure To configure an SMOD-type module on the DSP HUB data form Configuration by Snmp Network Management StationsNode nn command Enter To configure an IMOD-type module on the DSP HUB data form Order to receive traps Smod modems Diagnostic Tests Troubleshooting Alarms Indicator Status Error Messages Message Interpretation Error Messages Troubleshooting and Diagnostics Error Messages Pin Function Table A-1. Pin Allocation for Station CLK ConnectorStation Clock Interface LRSI-F-CM1 Module Pin Function Direction Management RS-232 Port Interface-LRSI-F-CM1 ModuleManagement RS-232 Port Interface-CM-1/CM-2 Modules Cont Station CLK Connector LRSI-F-CM2 Modules Ethernet Interface Connector LRSI-F2-CM2 Module Ethernet Interface Connector LRSI-F1-CM2 ModulePower Connectors Table A-5. LRSI-F1-CM Module, Ethernet Interface Connector LRS-PS-FEED Panels AC-Powered Unit Site Requirements DC-Powered Unit Not properly grounded DC-powered LRS-PS-FEED units require a -48 VDC power source Preparation for Installation Installation and Operation Power Connection Rack InstallationOperation Phantom Voltage Connection Order from Cutter Networks Ph727-398-5252/Fax727-397-9610 Snmp Environment ScopeSnmp Principles Snmp Operations MIB Structure Management Information Base General, Snmp agents support two types of access rights Access Restriction Using Snmp CommunitiesManagement Domains Under Snmp MIBs Supported by the LRS-24 Snmp Agent IP Environment IP EnvironmentCM-2 Communities IP Address Structure Address Class First Byte Address Range Table C-1. IP Address ClassByte Assignment of Addresses Default GatewayNet and Subnet Masks Routing of IP Management Traffic Snmp Traps Snmp Traps Appendix D CM-2 Management Commands Defining Dial-Up Modem Parameters ProcedurePurpose Format Table D-1. DEF Call Fields Command FieldsTable D-1lists the fields appearing on the data form Defining LRS-24 And CM-2 Snmp Agent Parameters Returning to Terminal Mode Table D-2describes fields on the data form Table D-2. DEF HUB Command Fields Hoursminutesseconds Bootp ON/OFF Table D-3 DEF HUB Command Fields Defining Management Stations HUB NMS Trap Update IP Addr Download Main Menu Defining CM-2 Download ParametersTypical data form is shown in Figure D-4 Table D-4. Download Main Menu Options CM2 Download via LANTo download via LAN Type Download via LAN screen appears CM2 Download via CM2 Flash CM2 Download via XmodemChange CM-2 Software Version To download via Xmodem 1. Type Type View CM2 Software Version screen appears View CM-2 Software VersionTo view CM-2 Software Version First line describes the version that is currently running Defining Modem Download ParametersControls the program version and allows six options Node nn DEF MDL Nn is the slot number Modem Download via Xmodem Modem Download via LANModem Download via CM2 Flash To download Modem via LAN To download to remote modem via Modem Flash Download to Remote Modem via Modem FlashDownload to Remote Modem VIA MODEM’S Flash Modem Status Master Permanent Select Modem Modem 1 Local View Modem Version on Modem Flash Changing Modem VersionTo change the Modem Version Type Changing Modem Version screen appears see Figure D-14 To view version of Modem software Type NODE13 DSP VER Enter Viewing Modem VersionModem Version screen appears see Figure D-16 Table D-5. Modem Version Parameters Modem Reset Factory Reset Card Reset Modem Advanced SetupDefining I/O Module Management Parameters Node nn DEF OPR Defines card type, name, and connection to a remote modem Defining Card ConfigurationDefine Card Type Empty Null Linked Node nn DEF PRM Defining I/O Module Operational Parameters Defining Supervision Terminal Type Modem SetupData Rate Parity CD Sense Clock Source LOC/REM Lintrrcv Terminal selection form appears. a typical form is shown Table D-6. Terminal TypesTo select a terminal Define Terminal Type Node nn DEF TST Defining I/O Module DiagnosticsModem Diagnostic Auto Configuration Menu Defining Auto-ConfigurationAuto-Configuration Menu screen appears see Figure D-22 To edit the Configuration Editing the ConfigurationFile number User String You can send or execute Hub Configuration files Hub Configuration OperationsTo execute a Hub Configuration file Operations for HUB Configuration File Input Imedance To configure a modem fileEditing a Modem File To configure according to modem type To execute the modem configuration fileEdit AUTO-CONFIGURATION Edit Auto Configuration AUTO-CONFIGURATION According to Modem Type To configure according to a specific slot/modem list Modem Number AUTO-CONFIGURATION According to SLOT/MODEM List To send a configuration file to the LRS-24 hub Sending Configuration FilesTo send the file by Tftp Select Tftp Download via LAN Screen appears see Figure D-33 Viewing Configuration Files in the Hub Creating Files from an Existing ConfigurationTo create a file from the existing configuration To view configuration files in the LRS-24 hub View Configuration Files in HUB Displaying General Alarm StatusAlarm status display form appears. a typical form is shown Message Description Display FormatTable D-7. Current Management Fields Node nn DSP ALT Displaying I/O Module Alarm Status Modem Alram Status Displaying System StatusTypical display is shown in Figure D-40 Data Description Table D-8describes the fields in the displayTable D-8. Module Status Fields Node nn DSP LOG Displaying Alarms LogTo display the desired log Type DSP nn DSP LOG Enter Modem LOG File To display the information Type DSP nn DSP STT Enter Displaying I/O Module StatusNode nn DSP STT Define Password Define CM-2 ResetTo reset the CM-2 card To define the password Type Node 13 DEF PWDEnter To enter the help system Type HLP Enter Displaying Command OptionsType password Select YES or no to Enable Password Figure D-45. Hub Terminal Commands Screen Command Description Table D-9. Hub Terminal Commands Screen Order from Cutter Networks Ph727-398-5252/Fax727-397-9610 Cables Index User modules RADview Index