Rack Installation, Power Connection | RAD Data comm LRS-24 specs

LRS-24Installation and Operation Manual	Appendix B LRS-PS-FEED Power Supply

Rack Installation

Position the LRS-PS-FEED unit above LRS-24, leaving at least 1U free space, and fasten the unit with four screws to the rack side rails.

Power Connection

Note that only the AC-powered LRS-PS-FEED has a POWER (On/Off) switch; the DC-powered unit does not have a power switch, and therefore it will start operating when DC power is applied.

➤To avoid turning on LRS-PS-FEED when connecting the power cables:

1.Before connecting LRS-PS-FEED to AC power, set the On/Off switch on the LRS-PS-FEED panel to Off.

2.Use an external circuit breaker located near LRS-PS-FEED to control the supply of DC power, and protect the DC input line. Set circuit breaker to Off before connecting the DC power cable to the LRS-PS-FEED.

AC Power Connection

Supply AC power to LRS-PS-FEED through the 5 feet (1.5m) standard power cable terminated by a standard 3-prong plug.

Connect the power cable first to the connector on the panel of the LRS-PS-FEED, and then to the mains outlet.

DC Power Connection

Connect the power cable between the DC distribution panel and the

DC power connector of the LRS-PS-FEED. Pay attention to correct polarity.

Phantom Voltage Connection

Connect the connector of the Phantom Out cable of the LRS-PS-FEED to the designated Phantom Feed connector of the LRSI-PSP* interface module installed in the LRS-24.

Note * Interface module version, for example, LRS-PSPF1, LRS-PSPF2, etc.

Operation

➤To operate LRS-24 with LRS-PS-FEED:

1.Turn on LRS-24 before powering up LRS-PS-FEED.

2.After LRS-24 is operating, apply power to LRS-PS-FEED. The Power indicators of the LRS-PS-FEED light up.

3.When turning off the system, first turn off LRS-PS-FEED; then turn off LRS-24.

Installation and Operation

B-5

Order from: Cutter Networks

Ph:727-398-5252/Fax:727-397-9610

www.bestdatasource.com

Image 93

RAD Data comm LRS-24 operation manual Rack Installation, Power Connection, Operation, Phantom Voltage Connection

Contents

RAD Data Communications Headquarters US East US West LRS-24 Order from Cutter Networks Ph727-398-5252/Fax727-397-9610 Warranty Ports Safety Status Safety Warnings Regulatory Information Supplementary Information Safety To turn the power on Power-OnLRS-24 with CM-1 Module Normal Indications LRS-24 with CM-2 Module Preliminary Configuration Contents Troubleshooting and Diagnostics Management via the CM-1 ModuleManagement via the CM-2 Module Module CM-2 Front Panel List of Figures List of Tables CM-2 Module Station CLK Connector, Pin Allocation General Overview Management/CM-2 functions Power Supplies VersionsApplication Management of Local and Remote Distribution Nodes Features Remote Management Clock Power SuppliesRADview-HPOV Snmp Management System RADview-PC/MDM Management System Chassis Description Physical Description LRS-24B 3-D View LRS-24B Enclosure LRS-24F Enclosure 5shows a 3-dimensional view of LRS-24F Front View LRS-24 Module Slots Functional Description Power Supply PS Modules Common Logic Modules Management CM-1 Management CapabilitiesCM-2 Management Capabilities Technical Specifications User ModulesNumber Functionality Word format software-configurableModules Data rates up to 9.6 kbps Temperature Humidity Up to 90%, non-condensing Operating Temperature StorageHardware To 113 F / 0 C to 45 C Introduction Mechanical DataSkilled technician who is aware of the hazards involved LRS-24F Mechanical Diagram LRS-24B Mechanical Diagram DC Power AC PowerInterface Module Handling Precautions Site Requirements and Prerequisites Unpacking the Chassis Module Handling PrecautionsFront Clearance Ambient Requirements PS Modules Installation and SetupFront Panels Before removing it from the enclosure Fuses PS Modules, Front Panel Indicators To install the first PS module PS Module InstallationAn AC and a DC PS module can be installed at the same time CM-1 Module Function Module CM-1, Front Panel Components Module CM-1, Internal Jumpers Internal Jumpers Module CM-1 Jumper Settings CM-1 Installation Procedure To install CM-1CM-2 Module Module CM-2, Front Panel Indicator Function Module CM-2, Internal Jumpers Module CM-2 Jumper Settings CM-2 InstallationTo install CM-2 Interfaces and Connections PS Interface Module Types PS Interface Modules To install the PS interface module Interface Module InstallationInterface Module Front Panel Typical LRSI-F-CM1 module front panel is shown in Figure To install LRSI-F-CM1 Interface module LRSI-F-1-CM2 / LRSI-B-1-CM2 Interface Modules with 10BaseTLRSI-F-1-CM2 10BT / LRSI-B-1-CM2 Front Panel Module panel includes two connectors Management 10BT Ethernet LEDsColor Indication JP8 LRSI-F-1-CM2 Internal Settings LRSI-F-1-CM2 Module Jumper Settings LRSI-F-1-CM2 InstallationTo install LRSI-F-1-CM2 LRSI-F-2-CM2 Interface Module with 10Base2 12. LRSI-F-2-CM2 Interface Module Panel with 10B2 LRSI-F-2-CM2 Internal Settings Jumpers Controls Settings/Options LRSI-F-2-CM2 Interface Module Jumper Settings LRS-24 Enclosure DC Power Connection AC Power ConnectionTo connect LRS-24 to AC power To connect LRS-24 to DC power Dry Contact Alarm Connections Station Clock ConnectionsManagement Connections Initial Operation and Basic Checks Power OnLRS-24 with CM-1 Module Connection to I/O User Modules Troubleshooting Power OffLRS-24 with CM-2 Module To turn off LRS-24 CM-1 To turn off LRS-24 with CM-2 Installation and Setup Management Capabilities CM-1 Functions Management RS-232 Port Interface Characteristics Terminal CharacteristicsConnecting the Terminal Default data rate 38.4 kbps Connection through Modem Link Direct Connection of Supervision Terminal Configuring the Terminal Select the full-duplex mode Turn off the terminal echoOperating the CM-1 Supervision Terminal Configuring Individual Modules Performing Preliminary ConfigurationTo configure each module Module is installed Management via the CM-1 Module CM-2 Module Capabilities Chapter Management via the CM-2 Module CM-2 Functions Handling of Management Communication Management Priorities Preliminary Configuration Activities Preliminary Configuration of Other Modules Preliminary Configuration of CM-2 moduleInitializing CM-2 Modules with Internal Snmp Agent Modules without Internal Agent Replacement of CM-2 module if a CM-2 module is plugged into Terminal Connection Methods RS-232 Supervisory Port Interface CharacteristicsConnection of Management Station Connection of Supervision Terminal LRS-24 Typical Connection of Supervision Terminal Through Slip Typical Connection to Network Management Station Command Protocol Command Language SyntaxFor a complete description of each command, see Appendix D CM-2 Supervision Terminal Language Index of Commands Errors ExecutionCommand Function/Action Supervision Terminal Operating Instructions Terminal Command Set Index for CM-2 Module Factory set password is radlrs Changing the PasswordTo change the password Type Node 13 DEF PWD Enter Password Menu Screen appears see Figure To configure an SMOD-type module on the DSP HUB data form Configuration by Snmp Network Management StationsNode nn command Enter To configure an IMOD-type module on the DSP HUB data form Order to receive traps Smod modems Diagnostic Tests Troubleshooting Alarms Indicator Status Error Messages Message Interpretation Error Messages Troubleshooting and Diagnostics Error Messages Table A-1. Pin Allocation for Station CLK Connector Station Clock Interface LRSI-F-CM1 ModulePin Function Management RS-232 Port Interface-LRSI-F-CM1 Module Management RS-232 Port Interface-CM-1/CM-2 ModulesPin Function Direction Cont Station CLK Connector LRSI-F-CM2 Modules Ethernet Interface Connector LRSI-F2-CM2 Module Ethernet Interface Connector LRSI-F1-CM2 ModulePower Connectors Table A-5. LRSI-F1-CM Module, Ethernet Interface Connector LRS-PS-FEED Panels AC-Powered Unit Site Requirements DC-Powered Unit Not properly grounded DC-powered LRS-PS-FEED units require a -48 VDC power source Preparation for Installation Installation and Operation Power Connection Rack InstallationOperation Phantom Voltage Connection Order from Cutter Networks Ph727-398-5252/Fax727-397-9610 Snmp Environment ScopeSnmp Principles Snmp Operations MIB Structure Management Information Base General, Snmp agents support two types of access rights Access Restriction Using Snmp CommunitiesManagement Domains Under Snmp MIBs Supported by the LRS-24 Snmp Agent IP Environment IP EnvironmentCM-2 Communities IP Address Structure Table C-1. IP Address Class ByteAddress Class First Byte Address Range Default Gateway Net and Subnet MasksAssignment of Addresses Routing of IP Management Traffic Snmp Traps Snmp Traps Appendix D CM-2 Management Commands Defining Dial-Up Modem Parameters ProcedurePurpose Format Command Fields Table D-1lists the fields appearing on the data formTable D-1. DEF Call Fields Defining LRS-24 And CM-2 Snmp Agent Parameters Returning to Terminal Mode Table D-2describes fields on the data form Table D-2. DEF HUB Command Fields Hoursminutesseconds Bootp ON/OFF Table D-3 DEF HUB Command Fields Defining Management Stations HUB NMS Trap Update IP Addr Defining CM-2 Download Parameters Typical data form is shown in Figure D-4Download Main Menu Table D-4. Download Main Menu Options CM2 Download via LANTo download via LAN Type Download via LAN screen appears CM2 Download via CM2 Flash CM2 Download via XmodemChange CM-2 Software Version To download via Xmodem 1. Type View CM-2 Software Version To view CM-2 Software VersionType View CM2 Software Version screen appears First line describes the version that is currently running Defining Modem Download ParametersControls the program version and allows six options Node nn DEF MDL Nn is the slot number Modem Download via Xmodem Modem Download via LANModem Download via CM2 Flash To download Modem via LAN To download to remote modem via Modem Flash Download to Remote Modem via Modem FlashDownload to Remote Modem VIA MODEM’S Flash Modem Status Master Permanent Select Modem Modem 1 Local View Modem Version on Modem Flash Changing Modem VersionTo change the Modem Version Type Changing Modem Version screen appears see Figure D-14 To view version of Modem software Type NODE13 DSP VER Enter Viewing Modem VersionModem Version screen appears see Figure D-16 Table D-5. Modem Version Parameters Modem Reset Factory Reset Card Reset Modem Advanced SetupDefining I/O Module Management Parameters Node nn DEF OPR Defines card type, name, and connection to a remote modem Defining Card ConfigurationDefine Card Type Empty Null Linked Node nn DEF PRM Defining I/O Module Operational Parameters Defining Supervision Terminal Type Modem SetupData Rate Parity CD Sense Clock Source LOC/REM Lintrrcv Terminal selection form appears. a typical form is shown Table D-6. Terminal TypesTo select a terminal Define Terminal Type Defining I/O Module Diagnostics Modem DiagnosticNode nn DEF TST Defining Auto-Configuration Auto-Configuration Menu screen appears see Figure D-22Auto Configuration Menu To edit the Configuration Editing the ConfigurationFile number User String You can send or execute Hub Configuration files Hub Configuration OperationsTo execute a Hub Configuration file Operations for HUB Configuration File To configure a modem file Editing a Modem FileInput Imedance To configure according to modem type To execute the modem configuration fileEdit AUTO-CONFIGURATION Edit Auto Configuration AUTO-CONFIGURATION According to Modem Type To configure according to a specific slot/modem list Modem Number AUTO-CONFIGURATION According to SLOT/MODEM List To send a configuration file to the LRS-24 hub Sending Configuration FilesTo send the file by Tftp Select Tftp Download via LAN Screen appears see Figure D-33 Viewing Configuration Files in the Hub Creating Files from an Existing ConfigurationTo create a file from the existing configuration To view configuration files in the LRS-24 hub Displaying General Alarm Status Alarm status display form appears. a typical form is shownView Configuration Files in HUB Display Format Table D-7. Current Management FieldsMessage Description Node nn DSP ALT Displaying I/O Module Alarm Status Displaying System Status Typical display is shown in Figure D-40Modem Alram Status Table D-8describes the fields in the display Table D-8. Module Status FieldsData Description Node nn DSP LOG Displaying Alarms LogTo display the desired log Type DSP nn DSP LOG Enter Modem LOG File Displaying I/O Module Status Node nn DSP STTTo display the information Type DSP nn DSP STT Enter Define Password Define CM-2 ResetTo reset the CM-2 card To define the password Type Node 13 DEF PWDEnter Displaying Command Options Type password Select YES or no to Enable PasswordTo enter the help system Type HLP Enter Figure D-45. Hub Terminal Commands Screen Command Description Table D-9. Hub Terminal Commands Screen Order from Cutter Networks Ph727-398-5252/Fax727-397-9610 Cables Index User modules RADview Index