Displaying Alarms Log, Node nn DSP LOG | RAD Data comm LRS-24

Appendix D CM-2 Management Commands		LRS-24Installation and Operation Manual

D.16 Displaying Alarms Log

Purpose

Displays the contents of the alarm history buffer of the CM-2 module, or of other selected I/O module. This buffer contains the last 20 alarms and events (for example, module insertion/removal).

The alarm log is cleared automatically when LRS-24 is turned off.

Format

NODE nn DSP LOG

Procedure

➤To display the desired log:

• Type: DSP nn DSP LOG <Enter>.

nnstands for the node number of the desired module, in the range of 1 through 12.

The log of the specified module appears.

The contents of the form depend on the module type. Refer to the Installation and Operation Manual of the corresponding module for detailed information.

A typical alarm display for the hub log, displayed in response to a request addressed to the CM-2 module (node 13), is shown in Figure D-41.

MODEM LOG FILE

MODEM NAME: ASMI-31CQ(m)

DEFINE PORT NUMBER

: 1

SELECT MODEM

: MODEM 1 LOCAL

CODE

STATE

DESCRIPTION

TIME

DATE

12

OFF

NearEndMngLinkFail

09:01 2000-03-09

08

OFF

NearEndSyncLoss

09:01 2000-03-09

12

ON

NearEndSyncLoss

09:01

2000-03-09

THERE ARE NO MORE PAGES AT THE MOMENT

Figure D-41. Hub Log File Screen

D-38 Displaying Alarms Log

Order from: Cutter Networks

Ph:727-398-5252/Fax:727-397-9610

www.bestdatasource.com

Image 140

RAD Data comm LRS-24 Displaying Alarms Log, Node nn DSP LOG, To display the desired log Type DSP nn DSP LOG Enter

Contents

LRS-24 RAD Data Communications Headquarters US East US West Order from Cutter Networks Ph727-398-5252/Fax727-397-9610 Warranty Safety Warnings Ports Safety Status Regulatory Information Safety Supplementary Information Power-On To turn the power onLRS-24 with CM-1 Module Normal Indications Preliminary Configuration LRS-24 with CM-2 Module Contents Management via the CM-2 Module Troubleshooting and DiagnosticsManagement via the CM-1 Module List of Figures Module CM-2 Front Panel CM-2 Module Station CLK Connector, Pin Allocation List of Tables Overview General Management/CM-2 functions Application Power SuppliesVersions Features Management of Local and Remote Distribution Nodes Clock Power Supplies Remote ManagementRADview-HPOV Snmp Management System RADview-PC/MDM Management System Physical Description Chassis Description LRS-24B 3-D View LRS-24B Enclosure 5shows a 3-dimensional view of LRS-24F LRS-24F Enclosure LRS-24 Module Slots Front View Power Supply PS Modules Functional Description Common Logic Modules CM-2 Management Capabilities ManagementCM-1 Management Capabilities Number Technical SpecificationsUser Modules Word format software-configurable FunctionalityModules Data rates up to 9.6 kbps Operating Temperature Storage Temperature Humidity Up to 90%, non-condensingHardware To 113 F / 0 C to 45 C Skilled technician who is aware of the hazards involved IntroductionMechanical Data LRS-24F Mechanical Diagram LRS-24B Mechanical Diagram AC Power DC PowerInterface Module Handling Precautions Site Requirements and Prerequisites Module Handling Precautions Unpacking the ChassisFront Clearance Ambient Requirements Installation and Setup PS ModulesFront Panels Before removing it from the enclosure PS Modules, Front Panel Indicators Fuses PS Module Installation To install the first PS moduleAn AC and a DC PS module can be installed at the same time CM-1 Module Module CM-1, Front Panel Components Function Internal Jumpers Module CM-1, Internal Jumpers Module CM-1 Jumper Settings CM-2 Module CM-1 Installation ProcedureTo install CM-1 Indicator Function Module CM-2, Front Panel Module CM-2, Internal Jumpers CM-2 Installation Module CM-2 Jumper SettingsTo install CM-2 Interfaces and Connections PS Interface Modules PS Interface Module Types Interface Module Installation To install the PS interface moduleInterface Module Front Panel Typical LRSI-F-CM1 module front panel is shown in Figure LRSI-F-1-CM2 10BT / LRSI-B-1-CM2 Front Panel To install LRSI-F-CM1 Interface moduleLRSI-F-1-CM2 / LRSI-B-1-CM2 Interface Modules with 10BaseT Color Indication Module panel includes two connectorsManagement 10BT Ethernet LEDs LRSI-F-1-CM2 Internal Settings JP8 LRSI-F-1-CM2 Installation LRSI-F-1-CM2 Module Jumper SettingsTo install LRSI-F-1-CM2 LRSI-F-2-CM2 Interface Module with 10Base2 LRSI-F-2-CM2 Internal Settings 12. LRSI-F-2-CM2 Interface Module Panel with 10B2 LRSI-F-2-CM2 Interface Module Jumper Settings Jumpers Controls Settings/Options LRS-24 Enclosure AC Power Connection DC Power ConnectionTo connect LRS-24 to AC power To connect LRS-24 to DC power Management Connections Dry Contact Alarm ConnectionsStation Clock Connections Power On Initial Operation and Basic ChecksLRS-24 with CM-1 Module Connection to I/O User Modules Power Off TroubleshootingLRS-24 with CM-2 Module To turn off LRS-24 CM-1 To turn off LRS-24 with CM-2 Installation and Setup CM-1 Functions Management Capabilities Terminal Characteristics Management RS-232 Port Interface CharacteristicsConnecting the Terminal Default data rate 38.4 kbps Direct Connection of Supervision Terminal Connection through Modem Link Operating the CM-1 Supervision Terminal Configuring the TerminalSelect the full-duplex mode Turn off the terminal echo Performing Preliminary Configuration Configuring Individual ModulesTo configure each module Module is installed Management via the CM-1 Module Chapter Management via the CM-2 Module CM-2 Module Capabilities CM-2 Functions Handling of Management Communication Preliminary Configuration Activities Management Priorities Preliminary Configuration of CM-2 module Preliminary Configuration of Other ModulesInitializing CM-2 Modules with Internal Snmp Agent Replacement of CM-2 module if a CM-2 module is plugged into Modules without Internal Agent RS-232 Supervisory Port Interface Characteristics Terminal Connection MethodsConnection of Management Station Connection of Supervision Terminal LRS-24 Typical Connection of Supervision Terminal Through Slip Typical Connection to Network Management Station Command Language Syntax Command ProtocolFor a complete description of each command, see Appendix D CM-2 Supervision Terminal Language Command Function/Action Index of CommandsErrors Execution Terminal Command Set Index for CM-2 Module Supervision Terminal Operating Instructions Changing the Password Factory set password is radlrsTo change the password Type Node 13 DEF PWD Enter Password Menu Screen appears see Figure Configuration by Snmp Network Management Stations To configure an SMOD-type module on the DSP HUB data formNode nn command Enter To configure an IMOD-type module on the DSP HUB data form Smod modems Order to receive traps Alarms Diagnostic Tests Troubleshooting Error Messages Indicator Status Error Messages Message Interpretation Troubleshooting and Diagnostics Error Messages Pin Function Table A-1. Pin Allocation for Station CLK ConnectorStation Clock Interface LRSI-F-CM1 Module Pin Function Direction Management RS-232 Port Interface-LRSI-F-CM1 ModuleManagement RS-232 Port Interface-CM-1/CM-2 Modules Station CLK Connector LRSI-F-CM2 Modules Cont Ethernet Interface Connector LRSI-F1-CM2 Module Ethernet Interface Connector LRSI-F2-CM2 ModulePower Connectors Table A-5. LRSI-F1-CM Module, Ethernet Interface Connector AC-Powered Unit LRS-PS-FEED Panels DC-Powered Unit Site Requirements DC-powered LRS-PS-FEED units require a -48 VDC power source Not properly grounded Installation and Operation Preparation for Installation Rack Installation Power ConnectionOperation Phantom Voltage Connection Order from Cutter Networks Ph727-398-5252/Fax727-397-9610 Scope Snmp EnvironmentSnmp Principles Snmp Operations Management Information Base MIB Structure Access Restriction Using Snmp Communities General, Snmp agents support two types of access rightsManagement Domains Under Snmp MIBs Supported by the LRS-24 Snmp Agent IP Environment IP EnvironmentCM-2 Communities IP Address Structure Address Class First Byte Address Range Table C-1. IP Address ClassByte Assignment of Addresses Default GatewayNet and Subnet Masks Snmp Traps Routing of IP Management Traffic Snmp Traps Appendix D CM-2 Management Commands Procedure Defining Dial-Up Modem ParametersPurpose Format Table D-1. DEF Call Fields Command FieldsTable D-1lists the fields appearing on the data form Returning to Terminal Mode Defining LRS-24 And CM-2 Snmp Agent Parameters Table D-2. DEF HUB Command Fields Table D-2describes fields on the data form Hoursminutesseconds Table D-3 DEF HUB Command Fields Bootp ON/OFF HUB NMS Trap Update IP Addr Defining Management Stations Download Main Menu Defining CM-2 Download ParametersTypical data form is shown in Figure D-4 CM2 Download via LAN Table D-4. Download Main Menu OptionsTo download via LAN Type Download via LAN screen appears CM2 Download via Xmodem CM2 Download via CM2 FlashChange CM-2 Software Version To download via Xmodem 1. Type Type View CM2 Software Version screen appears View CM-2 Software VersionTo view CM-2 Software Version Defining Modem Download Parameters First line describes the version that is currently runningControls the program version and allows six options Node nn DEF MDL Nn is the slot number Modem Download via LAN Modem Download via XmodemModem Download via CM2 Flash To download Modem via LAN Download to Remote Modem via Modem Flash To download to remote modem via Modem FlashDownload to Remote Modem VIA MODEM’S Flash Modem Status Master Permanent Select Modem Modem 1 Local Changing Modem Version View Modem Version on Modem FlashTo change the Modem Version Type Changing Modem Version screen appears see Figure D-14 Viewing Modem Version To view version of Modem software Type NODE13 DSP VER EnterModem Version screen appears see Figure D-16 Table D-5. Modem Version Parameters Modem Advanced Setup Modem Reset Factory Reset Card ResetDefining I/O Module Management Parameters Node nn DEF OPR Defining Card Configuration Defines card type, name, and connection to a remote modemDefine Card Type Empty Null Linked Defining I/O Module Operational Parameters Node nn DEF PRM Modem Setup Defining Supervision Terminal TypeData Rate Parity CD Sense Clock Source LOC/REM Lintrrcv Table D-6. Terminal Types Terminal selection form appears. a typical form is shownTo select a terminal Define Terminal Type Node nn DEF TST Defining I/O Module DiagnosticsModem Diagnostic Auto Configuration Menu Defining Auto-ConfigurationAuto-Configuration Menu screen appears see Figure D-22 Editing the Configuration To edit the ConfigurationFile number User String Hub Configuration Operations You can send or execute Hub Configuration filesTo execute a Hub Configuration file Operations for HUB Configuration File Input Imedance To configure a modem fileEditing a Modem File To execute the modem configuration file To configure according to modem typeEdit AUTO-CONFIGURATION Edit Auto Configuration To configure according to a specific slot/modem list AUTO-CONFIGURATION According to Modem Type AUTO-CONFIGURATION According to SLOT/MODEM List Modem Number Sending Configuration Files To send a configuration file to the LRS-24 hubTo send the file by Tftp Select Tftp Download via LAN Screen appears see Figure D-33 Creating Files from an Existing Configuration Viewing Configuration Files in the HubTo create a file from the existing configuration To view configuration files in the LRS-24 hub View Configuration Files in HUB Displaying General Alarm StatusAlarm status display form appears. a typical form is shown Message Description Display FormatTable D-7. Current Management Fields Displaying I/O Module Alarm Status Node nn DSP ALT Modem Alram Status Displaying System StatusTypical display is shown in Figure D-40 Data Description Table D-8describes the fields in the displayTable D-8. Module Status Fields Displaying Alarms Log Node nn DSP LOGTo display the desired log Type DSP nn DSP LOG Enter Modem LOG File To display the information Type DSP nn DSP STT Enter Displaying I/O Module StatusNode nn DSP STT Define CM-2 Reset Define PasswordTo reset the CM-2 card To define the password Type Node 13 DEF PWDEnter To enter the help system Type HLP Enter Displaying Command OptionsType password Select YES or no to Enable Password Figure D-45. Hub Terminal Commands Screen Table D-9. Hub Terminal Commands Screen Command Description Order from Cutter Networks Ph727-398-5252/Fax727-397-9610 Index Cables User modules RADview Index