Runco SP-42, SP-50, SP-60 specs

Specifications

49.1

44.0

47.9

1.2

4.0 29.9

6.9

4.6

0

9.0

14.9

20.8

29.9

0

14.8

34.3

49.1

Figure 7-2. CinemaWall Model SP-50 Dimensions (with Optional Table Stand)

68 Runco CinemaWall SP-42/-50/-60 Owner’s Operating Manual

Image 78

Runco SP-42, SP-60 manual CinemaWall Model SP-50 Dimensions with Optional Table Stand

Contents

SP-42 SP-50 SP-60 Page Three Year Limited Warranty For Plasma Displays RIGHTS, Limits and Exclusions Runco INTERNATIONAL, INC Safety Precautions Table of Contents Operation Maintenance and TroubleshootingSpecifications Serial Communications List of Figures Page Introduction About This Manual Using This Manual If you need Turn to Description, Features and Benefits Key Features and Benefits Optional Accessories Controls and Indicators Controls and FunctionsCinemaWall at a Glance Display Stand Connectors SP-42, SP-50 and SP-60 respectively SP-50 Connector Panel Combination IN/OUT CinemaWall Remote Control Main Power Switch SET Button Page Installation Remote Control Other surfaces Quick Setup Step Procedure For Details, refer to High-Altitude Operation InstallationConsiderations Mounting the CinemaWall Ambient Light Ventilation Installation Connections to the CinemaWall Video Connections Standby mode Analog RGB OUT Input 1 Connection Computer/Video Signal Compatibility on Composite or S-Video Input 3 Connection Component Video Input 4 Connection Audio Connections Attaching the Small Ferrite Cores to Audio Cables 11. Audio Output Connection RS-232 Controller ConnectionPage Turning on the Power OperationChanging the OSD Language Selecting an Input Source Viewing Input Signal Information Setting the Computer Display Properties Changing the Aspect Ratio Aspect Ratio Settings Aspect Ratio Description PIX by PIX Using the On-Screen Menus Installer Adjust menu is intended for use by authorizedTrained service personnel only CinemaWall OSD Menu Structure Main Menu Picture Typical Gray Bar Pattern for Adjusting Contrast Gray Yellow Cyan Green Magenta Red Blue Typical Test Pattern for Adjusting Sharpness Screen Power Set-UpOFF DVI Setup Language Refer to Changing the OSD Language on Option Under some conditions such as when the input signal consists Option Installer Adjust Mode Installer ADJ Input FAN Speed Auto ISF CCC color mode is pre-set to approximately 3,200K Seamless Switch is not available when using PIP This action is not undoable. Proceed with caution Using Picture-In-Picture PIP To use PIP, press the Split button Swapping the Main PIP Windows Enlarging One Part of the Screen Viewing an Enlarged Area of the DisplayPage Troubleshooting Tips Maintenance and TroubleshootingCleaning Cleaning the Display Panel Body and Remote Control Shut Down OUT of Range Signal NGThermal Alert FAN Failure Serial Communications RS-232 Connection and Port ConfigurationSerial Command Syntax Example Input Select Note Command Value Range DescriptionMinimum Maximum Aspect Ratio Video AudioPicture-in-Picture PIP MSTS08 MSTS09MSTS10 Side-by-side, full height main screen SET-UP Menu CommandsSets 2-screen operation to 2 Screen On left LOW High Option Menu Commands AverageAuto Picture Menu Commands Installer Adjust Mode Screen Menu Commands Installer Adjust Mode SET-UP Menu Commands Installer Adjust ModeOption Menu Commands Installer Adjust Mode FMKS03 FMKS00FMKS02 FMKS04 4F 53 44 53 30 Sets OSD Display to OFF DWF Minimum Maximum Adjustment CommandsDW1 UPF Specifications CinemaWall Specifications Specifications are subject to change without notice Date of delivery to the end user Dimensions CinemaWall CinemaWall Model SP-50 Dimensions with Optional Table Stand CinemaWall Model SP-60 Dimensions with Optional Table Stand Remarks Computer/Video Signal CompatibilityInput Refresh Rate Resolution Horiz 56.0 45.1 Page Page Runco CL-810 Owner’s Operating Manual