Runco SP-50, SP-42, SP-60 guide

Specifications

M8 SCREW

28.114	8.429	0
	34.440

12.530

11.000

5.950

0

35.596

57.593

58.653

246.46

411.12

0

1.787 17.000

33.835

Figure 7-3. CinemaWall Model SP-60 Dimensions (with Optional Table Stand)

Runco CinemaWall SP-42/-50/-60 Owner’s Operating Manual

69

Image 79

Runco SP-50, SP-42 manual CinemaWall Model SP-60 Dimensions with Optional Table Stand

Contents

SP-42 SP-50 SP-60 Page For Plasma Displays Three Year Limited Warranty RIGHTS, Limits and Exclusions Runco INTERNATIONAL, INC Safety Precautions Table of Contents Serial Communications Maintenance and TroubleshootingSpecifications Operation List of Figures Page About This Manual Introduction If you need Turn to Using This Manual Key Features and Benefits Description, Features and Benefits Optional Accessories Controls and Functions Controls and IndicatorsCinemaWall at a Glance Display Stand SP-42, SP-50 and SP-60 respectively Connectors SP-50 Connector Panel Combination IN/OUT Main Power Switch CinemaWall Remote Control SET Button Page Remote Control Installation Other surfaces Step Procedure For Details, refer to Quick Setup Mounting the CinemaWall InstallationConsiderations High-Altitude Operation Ventilation Ambient Light Installation Video Connections Connections to the CinemaWall Analog RGB OUT Input 1 Connection Standby mode Composite or S-Video Input 3 Connection Computer/Video Signal Compatibility on Component Video Input 4 Connection Attaching the Small Ferrite Cores to Audio Cables Audio Connections 11. Audio Output Connection Connection RS-232 ControllerPage Operation Turning on the PowerChanging the OSD Language Setting the Computer Display Properties Selecting an Input Source Viewing Input Signal Information Changing the Aspect Ratio Aspect Ratio Description Aspect Ratio Settings PIX by PIX Installer Adjust menu is intended for use by authorized Using the On-Screen MenusTrained service personnel only CinemaWall OSD Menu Structure Picture Main Menu Typical Gray Bar Pattern for Adjusting Contrast Gray Yellow Cyan Green Magenta Red Blue Typical Test Pattern for Adjusting Sharpness Screen Set-Up PowerOFF DVI Setup Option Language Refer to Changing the OSD Language on Under some conditions such as when the input signal consists Installer ADJ Input Option Installer Adjust Mode FAN Speed Auto ISF CCC color mode is pre-set to approximately 3,200K This action is not undoable. Proceed with caution Seamless Switch is not available when using PIP To use PIP, press the Split button Using Picture-In-Picture PIP PIP Windows Swapping the Main Viewing an Enlarged Area of the Display Enlarging One Part of the ScreenPage Cleaning the Display Panel Body and Remote Control Maintenance and TroubleshootingCleaning Troubleshooting Tips FAN Failure OUT of Range Signal NGThermal Alert Shut Down Example RS-232 Connection and Port ConfigurationSerial Command Syntax Serial Communications Aspect Ratio Command Value Range DescriptionMinimum Maximum Input Select Note Audio VideoPicture-in-Picture PIP MSTS09 MSTS08MSTS10 On left SET-UP Menu CommandsSets 2-screen operation to 2 Screen Side-by-side, full height main screen High LOW Average Option Menu CommandsAuto Picture Menu Commands Installer Adjust Mode SET-UP Menu Commands Installer Adjust Mode Screen Menu Commands Installer Adjust ModeOption Menu Commands Installer Adjust Mode FMKS04 FMKS00FMKS02 FMKS03 4F 53 44 53 30 Sets OSD Display to OFF UPF Minimum Maximum Adjustment CommandsDW1 DWF CinemaWall Specifications Specifications Date of delivery to the end user Specifications are subject to change without notice CinemaWall Dimensions CinemaWall Model SP-50 Dimensions with Optional Table Stand CinemaWall Model SP-60 Dimensions with Optional Table Stand Horiz Computer/Video Signal CompatibilityInput Refresh Rate Resolution Remarks 56.0 45.1 Page Page Runco CL-810 Owner’s Operating Manual