Runco CL-810 Owner’s Operating Manual | Runco SP-42, SP-50, SP-60

SERIAL NUMBER

RUMA-011205

rev 11-29-06 v3.0

Runco International • 2900 Faber Street • Union City, CA 94587 • Ph (510) 324-7777 / (800) 23RUNCO / Fax (510) 324-9300

www.runco.com

Runco CL-810 Owner’s Operating Manual

Image 84

Runco SP-42, SP-50, SP-60 manual Runco CL-810 Owner’s Operating Manual

Contents

SP-42 SP-50 SP-60 Page Three Year Limited Warranty For Plasma Displays RIGHTS, Limits and Exclusions Runco INTERNATIONAL, INC Safety Precautions Table of Contents Maintenance and Troubleshooting SpecificationsOperation Serial Communications List of Figures Page Introduction About This Manual Using This Manual If you need Turn to Description, Features and Benefits Key Features and Benefits Optional Accessories Controls and Indicators Controls and FunctionsCinemaWall at a Glance Display Stand Connectors SP-42, SP-50 and SP-60 respectively SP-50 Connector Panel Combination IN/OUT CinemaWall Remote Control Main Power Switch SET Button Page Installation Remote Control Other surfaces Quick Setup Step Procedure For Details, refer to Installation ConsiderationsHigh-Altitude Operation Mounting the CinemaWall Ambient Light Ventilation Installation Connections to the CinemaWall Video Connections Standby mode Analog RGB OUT Input 1 Connection Computer/Video Signal Compatibility on Composite or S-Video Input 3 Connection Component Video Input 4 Connection Audio Connections Attaching the Small Ferrite Cores to Audio Cables 11. Audio Output Connection RS-232 Controller ConnectionPage Turning on the Power OperationChanging the OSD Language Selecting an Input Source Viewing Input Signal Information Setting the Computer Display Properties Changing the Aspect Ratio Aspect Ratio Settings Aspect Ratio Description PIX by PIX Using the On-Screen Menus Installer Adjust menu is intended for use by authorizedTrained service personnel only CinemaWall OSD Menu Structure Main Menu Picture Typical Gray Bar Pattern for Adjusting Contrast Gray Yellow Cyan Green Magenta Red Blue Typical Test Pattern for Adjusting Sharpness Screen Power Set-UpOFF DVI Setup Language Refer to Changing the OSD Language on Option Under some conditions such as when the input signal consists Option Installer Adjust Mode Installer ADJ Input FAN Speed Auto ISF CCC color mode is pre-set to approximately 3,200K Seamless Switch is not available when using PIP This action is not undoable. Proceed with caution Using Picture-In-Picture PIP To use PIP, press the Split button Swapping the Main PIP Windows Enlarging One Part of the Screen Viewing an Enlarged Area of the DisplayPage Maintenance and Troubleshooting CleaningTroubleshooting Tips Cleaning the Display Panel Body and Remote Control OUT of Range Signal NG Thermal AlertShut Down FAN Failure RS-232 Connection and Port Configuration Serial Command SyntaxSerial Communications Example Command Value Range Description Minimum MaximumInput Select Note Aspect Ratio Video AudioPicture-in-Picture PIP MSTS08 MSTS09MSTS10 SET-UP Menu Commands Sets 2-screen operation to 2 ScreenSide-by-side, full height main screen On left LOW High Option Menu Commands AverageAuto Picture Menu Commands Installer Adjust Mode Screen Menu Commands Installer Adjust Mode SET-UP Menu Commands Installer Adjust ModeOption Menu Commands Installer Adjust Mode FMKS00 FMKS02FMKS03 FMKS04 4F 53 44 53 30 Sets OSD Display to OFF Minimum Maximum Adjustment Commands DW1DWF UPF Specifications CinemaWall Specifications Specifications are subject to change without notice Date of delivery to the end user Dimensions CinemaWall CinemaWall Model SP-50 Dimensions with Optional Table Stand CinemaWall Model SP-60 Dimensions with Optional Table Stand Computer/Video Signal Compatibility Input Refresh Rate ResolutionRemarks Horiz 56.0 45.1 Page Page Runco CL-810 Owner’s Operating Manual