RS-232 Commands, Parameter min/max Value stored? | Runco VX-4C

RS-232 COMMANDS

COMMAND	PARAMETER (min/max)	Value stored?	DESCRIPTION

ON	NA	NA	Turns VHD Ultra Controller on
OFF	NA	NA	Turns VHD Ultra Controller off
DISPLAY	0/4	YES	Adjusts the brightness of the
			front panel display
COMPOSITE	NA	YES	Selects the Composite
			Video input
SVIDEO	NA	YES	Selects the S-Video Input
COMPONENT	NA	YES	Selects the Component
			Video input
PASSTHRU	NA	YES	Selects the Pass-through input
ANAMORPHIC	NA	YES	Selects the anamorphic
			aspect ratio
STANDARD	NA	YES	Selects the standard (4:3)
			aspect ratio
LETTERBOX	NA	YES	Selects the letterbox aspect ratio
TINT	-127/127	NO	Sets a value for tint
COLOR	-127/127	NO	Sets a value for color
AGCCOLOR	0/1	NO	0=Disable Color AGC
			1=Enable Color AGC
BRIGHTNESS	-127/127	NO	Sets a value for brightness
CONTRAST	-127/127	NO	Sets a value for contrast
AGCCONTRAST	0/1	NO	0=Disable Contrast AGC
			1=Enable Contrast AGC
SHARPNESS	0/255	NO	Sets a value for sharpness
CHROMAHIGH	0/127	NO	Sets a value for high-frequency
			chroma edge enhancement
CHROMALOW	0/127	NO	Sets a value for low-frequency
			chroma edge enhancement
LUMAHIGH	0/127	NO	Sets a value for high-frequency
			luminance edge enhancement
LUMALOW	0/127	NO	Sets a value for low-frequency
			luminance edge enhancement

6-20

Image 97

Runco VX-4C, VX-6C manual RS-232 Commands, Parameter min/max Value stored?

Contents

VX-4c and VX-6c Page Table of Contents Page How The Projector Works? Introduction Introduction Purchase Record and Servicing Components Connect the Line Cord to AC Power Quick SetupPosition the Projector Connect a Source Install the lens cap Installing The LensUnplug the projector Loosen 3 screws Rotate the lens barrel slightly Align zoom gear ring to access 3 screwsRotate Slightly Remove Lens Assembly Pull lens assembly outInstall new lens assembly Orientation Adjust Image Motorized Models Adjust ImageMotorized Lens Adjustments Lifting Installation ConsiderationsAdditional Considerations 720p Throw Distances Placement Section960p 1024p Calculating Throw Distance Maximum Vertical Offsets Fixed Lenses Vertical & Horizontal Position Maximum Vertical Offsets Zoom Lenses Mounting Maximum Horizontal Offset ALL LensesSpecial Mounting Horizontal and Vertical Tilt Ranges Folded Optics Rear Connector PanelSource Connections Connecting RGB Input RGB Signals Independent Keypads and Projectors Keypad Protocols and Conversion Step Remote Keypad Protocol IR or Wired KeypadOpening the Keypad Set the Jumpers Locating and Setting the Jumpers Converting a Keypad Shortcut Method Andy Siedschlag ISF 3C Calibration Information Projector Basics Overview Reading the Status LEDs Operation Keypad Commands Wired Remote OptionalPower ON/OFF IR Remote Memory Bank Input Arrow Keys Exit Color VolumeTint Detail Shutter Optional PositionMute Function Key Help OSD On-screen displayTest Runco Digital Home Navigating the MenusCinema Menu On-line Help Using Slidebars and Other Controls Accessing General Help TopicsTime-outs To save or To cancel. When you are done, press Editing Text Example of Pull-Down ListEntering Text Editing Numerical Values Using Inputs and Memory BanksSelecting an Input Creating a New Memory Bank Automatic What Memory Banks Are Defined So Far? Copying a Memory Bank Copying or Deleting Memory BanksDeleting a Memory Bank Editing a Memory Banks Operation Load Default Adjusting the ImageScaling Parameters Scaling Parameters Menu Fine V Dots Short CUT Press Image Adjustments Menu Image AdjustmentsShift Short CUT Press Blanking Top, Bottom, Left or Right Contrast Short CUT Press Signal TypeBrightness Short CUT Press Sharpness Set Color Balance Color BalanceGamma Curve Selected Gamma Curves Gamma Curve OSD Settings Menu IR and Serial Setup Menu Show Adjust BarDisplay M. Bank List Show Message Front IR Receiver / Back IR Receiver Wired Keypad Test Pattern Menu Test Patterns Menu Options Video TerminationSubmenu for Menu Options Installation Menu Test Patterns DMD Enable DMD Odd Pixel Advanced Color TemperatureDMD Odd Pixel Menu Operational Parameters Menu Color Balance Setup Menu Color Balance Setup Set Color Balance Presets and FactoryPresets Lamp Adjust submenu Lamp Adjust Operation Recording the New Lamp Serial Number Lamp Adjust Input Signal Error Error ConditionsInvalid User Entry Other Signal Error Messages No SignalSystem Warnings / Errors Bad Sync Status LED Codes System Errors System Error Codes Projector Location Maintenance Use only lamps supplied by Runco Lamp and Filter Replacement Ventilation CleaningServicing Lens Replacing Keypad Batteries CaseReplacing Keypad Batteries How Old is The Lamp? Cause / Remedy Troubleshooting Symptom The display is jittery or unstable Symptom The power is on but the lamp is notSymptom The display is faint Symptom The display appears compressed or stretched… Symptom The display is reversed and/or upside-down…Symptom The display is not sharp or clean… Symptom The display is not rectangular… Symptom Colors in the display are inaccurate…Symptom The display is noisy… Specifications Specifications VHD Ultra Controller Manual Remarque Safety Tips Introduction Front and Rear Panel Descriptions Rear Panel Power Input Remote Control Description Quick SET-UP Guide Menu Description and Navigation White Yellow Cyan Green Magenta Red Blue Page Installation Menu Screen Type Blanking Blanking Aspect Ratios Active image area Actual screen area Blanked cut off Areas Dimensions RS-232 Communications Parameter min/max Value stored? RS-232 Commands Command VHD Ultra Specifications Ambient Light Rejection Active Line TimeAnalog Video Aspect Ratio Display Setting Color TemperatureCheckbox Color Shift Help Screen Input SignalHorizontal Frequency Horizontal Offset Resolution lens Pixel PhaseResolution projector Menu RGB Video Source SetupRS-232 RS-422 Variable Scan Throw DistanceVertical Offset Video Decoder Keypad Reference Menu Tree Appendix C Page RUMA-010450