Mmc, RXD TXD DTR Sgnd CTS | Samsung NX-308 specification

2INSTALL 1999.9.15 12:45 PM 페이지34

NX-SERIESHYBRID KEY SYSTEM		INSTALLATION SECTION

	R-MMC	PC
	(9 PIN)	(9 PIN)
	RXD 2	2 RXD
	TXD 3	3 TXD
	DTR 4	4 DTR
	SGND 5	5 SGND
	CTS 8

NOTE : If the CTS pin is not connected, the system cannot check the printer (MODEM) status (power ON/OFF, paper empty, etc.)

FIGURE 7-4 SMDR & REMOTE PROGRAMMING CONNECTIONS

2 - 30

Image 37

Samsung NX-308 technical manual Mmc, RXD TXD DTR Sgnd CTS

Contents

NX-SERIES Publication Information 0preface 1999.9.15 1246 PM 페이지2 Technical Manual 0preface 1999.9.15 1246 PM 페이지4 Section 1GENERAL 1999.9.15 1246 PM 페이지2 Table of Contents NX-SERIESHYBRID KEY System NX-SERIES General System Diagram NX-308 System System OverviewNX-820 System NX-1232 System TOP View NX-SERIES LayoutSide View No. of Stations System Configuration 1GENERAL 1999.9.15 1246 PM 페이지9 Hardware Description KSU Key Service UnitExpansion Cards & Option Boards Station Equipment Electrical Specifications SpecificationsDimensions and Weights Environmental Limitations Continuous System Tones and Rings Condition LED Color LED Status Keyset LED Indications Installation Section 2INSTALL 1999.9.15 1245 PM 페이지2 Connecting Telephone Lines Connecting Station EquipmentBefore Power UP Installation Section AC Power Selection See Figure Installation Expansion Cards & Option Boards NX-DPH/PAGING Board See NX-SMDR/R-MMC Board SeeNX-MPD Board See NX-PRS Board See 13.2 NX-820 System See Figure MDFA-C Connections for NX-308 MDFB-C Connections for NX-820 MDFC-C Connections for NX-1232 MDFD-C Connectionsexpansion Card Optional MDF Connecting Station Equipment Connecting Telephone LinesSafety Precautions Connecting Keyset / AOM Figure 2 NX-820 KTS SLT NX-308 KSU Switch Locations NX-1232 KSU Switch Locations Doorphone and Door Lock Release See Figure Connecting Door Phone & Door Lock Release RXD TXD DTR Sgnd CTS MMC Connecting External Battery Before Power UP HOW to Remove the Handset Cord from the Handset Features Section 3feature 1999.9.15 1244 PM 페이지2 Feature ID Table Feature DescriptionsFeatures Section 3feature 1999.9.15 1244 PM 페이지4 System Features Feature Description Automatic Hold ALL Call VoiceBackground Music Call Hold Call Forwarding Call METERING/PRS Call HuntCall Pickup Call Waiting / CAMP-ON Direct Inward System Access Disa Class of ServiceChain Dialing Conference Directory Names Direct Trunk SelectionDistinctive Ringing Door Phones External page Interface External Music InterfaceFlash KEY Operation Flexible Numbering Group / OUT of Group Incoming / Outgoing ServiceIncoming Call Distribution Individual Line Control Meet ME page and Answer Night ServiceMessage Waiting Indication Microphone ON/OFF PER Station Operator Group OFF Premises Extension OPXOverflow Paging Programmable Timers Power Failure TransferPort Status Check Prime Line Selection SINGLE-LINE Connections Ring OverSPEED-DIAL Numbers Station Message Detail Recording Smdr Station Hunt GroupsStation to Station Calling Restriction System Directory Toll Restriction Override Toll RestrictionTone or Pulse Dialing Traffic Report Printout Transfer Trunk Disconnect SignalTrunk Groups Universal Night Answer UNA Appointment Reminder Alarm Clock Station FeaturesADD-ON Module AOM Busy Station Callback Automatic PrivacyBusy Station Indication BLF Direct Station Selection DSS Forced Auto Answer Executive / Secretary HOT LinesGroup Listening Headset Operation Line Skipping Line Queuing with CallbackMessage Waiting Light / Indication Mute Microphone / Handset Protection from BARGE-IN Pulse to Tone SwitchoverPULL-OUT Directory Tray Redial Speaker Phone Ringing Line PreferenceStation Lock TRI-COLORED Lights Display Features Call Processing Information Call for Group IdentificationCalling Party Name Calling Party Number Identification of Recalls Stopwatch TimerIdentification of Transfers Message Waiting Caller Number Feature Feature ID Feature ID Table Smdr Report for Sample Smdr printout Programming Section 4Programming 1999.9.15 1242 PM 페이지2 Programming Programming Procedures Programming Section Programming Overview Introduction to ProgrammingProgramming Levels Transfer Program KeysSpeaker Hold AS-Keyset Program List in Numerical Order Programming Procedures Program List in Alphabetical Order Program Procedures Default Data Procedure LCD DisplayStation Lock Related MMC Change Station Passcode Procedure Ring MMC 10SET Answer ModeAuto Answer Forward ALL Call ForwardForward Busy Forward no Answer Station ON/OFF SET Ring Frequency Pprocedure Station Names Western MMC 15DATA DisplayEastern KEY Extender Station SPEED-DIAL Open Programming Change Passcode Customer ON/OFF Zone Option BARGE-IN Type Description Assign BARGE-INOption BARGE-IN Class Description HOT/WARM Line Alarm Mode DAY Mode Alarm Reminder Vacant Message Call Disc Dial Digit Toll Class Descriptions Station Toll Class Dial Digit TRK USE Description EXT/TRK USE 0N for disallow intercom call 1Y for allow intercom call Intercom USE Assign Door Ring Display shows the first member of pickup group Assign Pickup Group Options Display Range Assign Station GroupRing Modes Description Group Types MMC MMC 36ASSIGN BOSS/SECRETARY If there is no AOM port, display shows Assign ADD-ON Module Dialing Types SLT Dialing Type Used to assign SLT ports to be used for data transmission Data Line PBX Line Dtmf Trunk Dialing TypePulse Trunk ON/OFF Procedure LCD DispalyOption Description Assign Trunk Ring Trunk Names Trunk Group Mode Description Options Description Assign Disa Line Table of Timers and Values MMC 50SYSTEM Timers First DGT Display Description Default Range DOR R OFFHook OFF Inter DGT Tone Name Display Data TONE/RING Cadence Options Description ALM Counter System Wide CounterArdl Counter MMC 53TRUNK Wide Timer Current Data and Time MAKE/BREAK Ratio Assign Auto Night Time Toll Deny TABLE/APPLY Call Cost Toll Allow TABLE/APPLY PBX Access Code Class Authorization Table Override Table Assign Wild Character Bypass Toll MMC 66 System SPD-DIAL Toll RestrictionFollow Toll Assign System SPEED-DIAL Dial Numbering Plan Station Group System KEY Programming MMC Station KEY Programming KEY Test Parameter Options System I/O Parameters Options Descriptions MMC 81SMDR Options Type Description Call Traffic Report Customer USE MMC System Version Default Data Related MMCPort Status Entry Number Language MMC 93LANGUAGE Selection Halt Process Clear Memory System Restart 4Programming 1999.9.15 1244 PM 페이지76 Appendix Section 5APPENDIX 1999.9.15 1241 PM 페이지2 Site Requirements Appendix a Remote ProgrammingCustomer Site Requirements Remote Site Requirements Progrmming Protocol Begin Programming ON-SITE Requirements ON-SITE Programming VIA PC Terminal Programming Protocol Customer Site Requirements Appendix B Database DownloadGetting Started Starting NX Download Program Appendix B Database Download Setup Of Database Downloading Program Open file Downloading Print file Save fileHelp Phrases Phrase Contents TimeRecord & Verify Message Appendix C Disa Voice Anouncement 1. Disa Automatic Answer Monitoring BACK-UP Data Sheets 6BACKUP 1999.9.15 1240 PM 페이지2 Database Forms 6BACKUP 1999.9.15 1240 PM 페이지4 Station Data System Configuration MMC 17 Station SPEED-DIAL Call ForwardMMC 21 Change Passcode Customer ON/OFF BARGE-IN MMC 26 Alarm ReminderMMC 25 HOT / Warm Line MMC 27 Vacant Message MMC 33 Assign Door Ring MMC 32 Intercom USEMMC 34 Pickup Group MMC 35 Station Group MMC 38 SLT Dialing Type MMC 37 ADD-ON ModuleData Line MMC 40 C.O. PBX Line MMC 45 Trunk Group System TimersMMC 46 Assign Disa Line Tone / Ring Cadence Trunk Wide TimerMake / Break Ratio Call Cost MMC 62 PBX Access CodeToll Deny Table / Apply Toll Allow Table / Apply MMC 64 Override Table MMC 63 Authorization CodeWild Character Assign System SPEED-DIAL IO Parameters Code GA68-60655A Edition 05 DN April