Samsung NX-308 MMC 20 OPEN PROGRAMMING

This MMC is used to open or close Customer or Technician level programming.

If programming is not opened and an attempt is made to access a system MMC, the error

message [NOT PERMIT] will be displayed. A four-digit Customer passcode is required to

access Customer level programming allocated in MMC 90 (Customer MMC Number). Or

a four-digit Technician level passcode is required to open all the MMCs.

PROCEDURE LCD DISPLAY

1. Press [TRANSFER] and dial 20

2. Enter passcode

Default passcodes:

1234 for customer level programming

4321 for technician level programming

3. Press [MUTE] or [MESSAGE] to select DISABLE or

ENABLE

Dial 0to select DISABLE

or 1for ENABLE

4. Press [TRANSFER] to save and exit

DEFAULT DATA

DISABLE

RELATED MMC

CUSTOMER PROGRAMMING: Refer to MMC 90

TECHNICIAN LEVEL PROGRAMMING : ALL MMCs

NX-SERIES HYBRID KEY SYSTEM PROGRAMMING SECTION

MMC 20 OPEN PROGRAMMING

Contents

Main PUBLICATION INFORMATION Page NX-SERIES Page Page Page GENERAL DESCRIPTION Page Page 1. SYSTEM OVERVIEW 1.1 NX-308 SYSTEM 1 - 2 1.2 NX-820 SYSTEM 1.3 NX-1232 SYSTEM 2. NX-SERIES LAYOUT 2.1 TOP VIEW 2.2 SIDE VIEW 3. SYSTEM CONFIGURATION 3.1 NX-308 SYSTEM 1 - 4 3.2 NX-820 SYSTEM No. of Stations 3.3 NX-1232 SYSTEM No. of Stations 1 - 5 4. HARDWARE DESCRIPTION 4.1 KSU (Key Service Unit) 1 - 6 NX-308 SYSTEM NX-820 SYSTEM NX-1232 SYSTEM 4.2 EXPANSION CARDS & OPTION BOARDS 4.3 STATION EQUIPMENT 1 - 7 5. SPECIFICATIONS 5.1 ELECTRICAL SPECIFICATIONS 1 - 8 5.2 DIMENSIONS AND WEIGHTS 5.3 ENVIRONMENTAL LIMITATIONS 5.5 SYSTEM TONES AND RINGS 1 - 9 5.6 KEYSET LED INDICATIONS 1 - 10 Page Page Page 2.3 AC Power Selection ( See FIGURE 2-2 ) 2 - 2 3. INSTALLATION EXPANSION CARDS & OPTION BOARDS Page 3.13.2 NX-820 SYSTEM ( See FIGURE 3-13) 3.13.3 NX-1232 SYSTEM ( See FIGURE 3-14 ) 2 - 8 FIGURE 4-1 MDFA-C CONNECTIONS FOR NX-308 2 - 10 FIGURE 4-3 MDFB-C CONNECTIONS FOR NX-820 2 - 12 FIGURE 4-5 MDFC-C CONNECTIONS FOR NX-1232 2 - 14 FIGURE 4-7 MDFD-C CONNECTIONS(EXPANSION CARD) 2 - 16 2 - 18 5. CONNECTING TELEPHONE LINES 5.1 SAFETY PRECAUTIONS 5.2 LOOP START LINES 6. CONNECTING STATION EQUIPMENT 6.1 CONNECTING KEYSET / AOM (FIGURE 6-1) S 2 - 24 2 - 26 7.3 DOORPHONE AND DOOR LOCK RELEASE (See FIGURE 7-3) 2 - 28 2 - 30 8. BEFORE POWER UP 2 - 32 9-3 HOW TO REMOVE THE HANDSET CORD FROM THE HANDSET Page Page FEATURES Page 1. FEATURE DESCRIPTION 1.1 SYSTEM FEATURES 3 - 1 Page Page Page Page Page Page Page Page Page Page Page Page Page Page 1.2 STATION FEATURES ADD-ON MODULE (AOM) 3 - 16 APPOINTMENT REMINDER (ALARM CLOCK) AUTOMATIC HOLD Page Page Page Page Page 1.3 DISPLAY FEATURES Page Page 2. FEATURE ID TABLE FEATURE FEATURE ID 3 - 25 < Sample SMDR printout > 3 - 26 Page Page PROGRAMMING 1. INTRODUCTION TO PROGRAMMING ................................ 4-1 2. PROGRAMMING PROCEDURES.......................................... 4-4 Page 1. INTRODUCTION TO PROGRAMMING 1.1 PROGRAMMING OVERVIEW 4 - 1 1.2 PROGRAMMING LEVELS SYSTEM LEVEL 1.3 PROGRAM KEYS 1.3.1 NX-keyset with LCD 4 - 2 1.3.2 Other LCD keysets AS-Keyset NX-keyset 816 keyset 4 - 3 2. PROGRAMMING PROCEDURES 2.1 PROGRAM LIST IN NUMERICAL ORDER 4 - 4 2.2 PROGRAM LIST IN ALPHABETICAL ORDER 4 - 5 2.3 PROGRAM PROCEDURES MMC 00 STATION LOCK MMC 01 CHANGE STATION PASSCODE MMC 10 SET ANSWER MODE MMC 11 CALL FORWARD MMC 12 STATION ON/OFF MMC 13 SET RING FREQUENCY PPROCEDURE LCD DISPLAY MMC 14 STATION NAMES MMC 15 DATA DISPLAY MMC 16 KEY EXTENDER MMC 17 STATION SPEED-DIAL MMC 20 OPEN PROGRAMMING MMC 21 CHANGE PASSCODE MMC 22 CUSTOMER ON/OFF MMC 23 PAGE ZONE MMC 24 ASSIGN BARGE-IN MMC 25 HOT/WARM LINE MMC 26 ALARM REMINDER MMC 27 VACANT MESSAGE MMC 28 CALL DISC MMC 30 STATION TOLL CLASS MMC 31 EXT/TRK USE PROCEDURE LCD DISPLAY DEFAULT DATA RELATED MMC MMC 32 INTERCOM USE MMC 33 ASSIGN DOOR RING MMC 34 ASSIGN PICKUP GROUP MMC 35 ASSIGN STATION GROUP MMC 35 MMC 36 ASSIGN BOSS/SECRETARY MMC 37 ASSIGN ADD-ON MODULE MMC 38 SLT DIALING TYPE MMC 39 DATA LINE MMC 40 C.O./PBX LINE MMC 41 TRUNK DIALING TYPE MMC 42 TRUNK ON/OFF PROCEDURE LCD DISPALY DEFAULT DATA MMC 43 ASSIGN TRUNK RING MMC 44 TRUNK NAMES MMC 45 TRUNK GROUP MMC 46 ASSIGN DISA LINE MMC 50 SYSTEM TIMERS TABLE OF TIMERS AND VALUES MMC 50 MMC 51 TONE/RING CADENCE MMC 52 SYSTEM WIDE COUNTER MMC 53 TRUNK WIDE TIMER DEFAULT DATA RELATED MMC MMC 54 MAKE/BREAK RATIO MMC 55 CURRENT DATA AND TIME MMC 56 ASSIGN AUTO NIGHT TIME MMC 57 CALL COST MMC 60 TOLL DENY TABLE/APPLY MMC 61 TOLL ALLOW TABLE/APPLY MMC 62 PBX ACCESS CODE MMC 63 AUTHORIZATION TABLE MMC 64 OVERRIDE TABLE MMC 65 ASSIGN WILD CHARACTER MMC 66 SYSTEM SPD-DIAL TOLL RESTRICTION MMC 67 ASSIGN SYSTEM SPEED-DIAL MMC 70 DIAL NUMBERING PLAN MMC 70 MMC 71 SYSTEM KEY PROGRAMMING MMC 71 MMC 72 STATION KEY PROGRAMMING MMC 73 KEY TEST MMC 80 SYSTEM I/O PARAMETERS MMC 81 SMDR OPTIONS MMC 83 CALL TRAFFIC REPORT MMC 90 CUSTOMER USE MMC MMC 91 SYSTEM VERSION MMC 92 PORT STATUS MMC 93 LANGUAGE SELECTION MMC 94 HALT PROCESS MMC 95 SYSTEM RESTART Page Page Page APPENDIX A 1. SITE REQUIREMENTS 5 - 1 1.1 CUSTOMER SITE REQUIREMENTS 1.2 REMOTE SITE REQUIREMENTS 1.3 BEGIN PROGRAMMING 1.4 PROGRMMING PROTOCOL 5 - 2 2. ON-SITE PROGRAMMING VIA PC TERMINAL 2.1 ON-SITE REQUIREMENTS 5 - 3 2.2 BEGIN PROGRAMMING NX-SERIES 2.3 PROGRAMMING PROTOCOL 5 - 4 APPENDIX B 1. Introduction To Database Download Programming 5 - 5 1.1 Customer Site Requirements 2. Installing Database Downloading 3. 2 Setup Of Database Downloading Program NX-SERIES 5 - 6 4. Using database downloading program 4.1 Downloading 5 - 7 4.2 Open file NX-SERIES Page APPENDIX C 1. DISA AUTOMATIC ANSWER 5 - 9 2. PHRASES 3. RECORD & VERIFY MESSAGE 3.3 Monitoring NX-SERIES 5 - 10 Page Page Page Page Page Page Page Page Page MMC 45 TRUNK GROUP MMC 46 ASSIGN DISA LINE COPY AS NEEDED SHEET _____ OF_______ MMC 50 SYSTEM TIMERS Page Page Page MMC 80 IO PARAMETERS MMC 81 SMDR OPTIONS COPY AS NEEDED SHEET _____ OF_______