Sun Microsystems 440 specification

D

default system console configuration, 4 device identifiers, listed, 47

device reconfiguration, manual, 48 device unconfiguration, manual, 46

DHCP (Dynamic Host Configuration Protocol), 17 diag-device(OpenBoot configuration

variable), 43 disk configuration

concatenation, 54 hot-spares, 56 mirroring, 54 RAID 0, 55 RAID 1, 55 RAID 5, 56 striping, 55

disk drives LEDs

Activity, 65 OK-to-Remove, 61, 64, 65

logical device names, table, 57 disk hot-plug

mirrored disk, 61 non-mirrored disk, 62

disk mirror (RAID 0), See hardware disk mirror disk slot number, reference, 57

disk striping with parity (RAID 5), 56 disk volumes

about, 51 deleting, 60

DMP (Dynamic Multipathing), 52 dtterm (Solaris utility), 23

Dynamic Host Configuration Protocol (DHCP) client on network management port, 17, 18

Dynamic Multipathing (DMP), 52

F

fsck (Solaris command), 12

G

go (OpenBoot command), 13 graceful system halt, 11, 14 graphics monitor

accessing system console from, 29 connecting to PCI graphics card, 29 restrictions against using for initial setup, 29 restrictions against using to view POST

output, 29

H

halt, gracefully, advantages of, 11, 14 hardware disk mirror

about, 56

checking the status of, 59 hot-plug operation, 61

hardware watchdog mechanism enabling, 49

hot-plug operation non-mirrored disk drive, 62 on hardware disk mirror, 61

hot-spares (disk drives), 56 See also disk conﬁguration

I

init (Solaris command), 11, 14 input-device(OpenBoot configuration

variable), 21, 29, 31

E

environmental information, viewing, 36 error handling, summary, 43 error-reset-recovery(OpenBoot

configuration variable), 49

escape sequence (#.), ALOM system controller, 9 externally initiated reset (XIR)

invoking from sc> prompt, 12

K keyboard

attaching, 29 keyboard sequences L1-A, 10, 11, 14

Stop-A (non-USB keyboard sequence), See L1-A keyboard sequence

Stop-D (non-USB keyboard sequence), 39

78 Netra 440 Server System Administration Guide • August 2004

Image 92

Sun Microsystems manual Netra 440 Server System Administration Guide August

Contents

Netra 440 Server System Administration Guide Page Contents Managing RAS Features and System Firmware Managing Disk Volumes Iv Netra 440 Server System Administration Guide August Figures Vi Netra 440 Server System Administration Guide August Tables Viii Netra 440 Server System Administration Guide August Preface How This Book Is Organized Using Unix Commands Shell Prompts Typographic Conventions Related Documentation Accessing Sun Documentation Third-Party Web SitesContacting Sun Technical Support Sun Welcomes Your Comments Configuring the System Console Communicating With the System 1Ways of Communicating With the System Using the System Console What the System Console Does Serial MGT NET MGT Alom serial management port Alom network management port Alternative System Console Configuration 3Alternative Console Ports Require Additional Configuration Accessing the System Console Through a Graphics Monitor About the sc Prompt Reaching the sc Prompt OpenBoot ok PromptAccess Through Multiple Controller Sessions Reaching the ok Prompt L1-A Stop-A Keys or Break Key Alom System Controller break or console CommandGraceful Shutdown Externally Initiated Reset XIR Manual System Reset For More Information Getting to the ok Prompt 2Ways of Accessing the ok Prompt To Get to the ok Prompt Console # Accessing the System Controller Using the Serial Management Port Establish an Alom system controller session Activating the Network Management PortTo Use the Serial Management Port Log out of the Alom system controller session To verify the network settings, typeTo Activate the Network Management Port Accessing the System Console Through a Terminal Server To Access The System Console Through a Terminal Server 3Pin Crossovers for Connecting to a Typical Terminal Server Open a terminal session on the connecting device, and type Accessing the System Console Through a TIP Connection Power on the system To Access the System Console Through the TIP Connection A shell tool window on the Sun system, type Ok power-off To Modify the /etc/remote File If the number displayed by the uname -rcommand is less thanModifying the /etc/remote File Netra 440 Server System Administration Guide August Ok setenv input-device ttyb ok setenv output-device ttyb Verifying Serial Port Settings on Ttyb To Verify the Serial Port Settings on TtybOpen a shell tool window Type Look for the following output For more information, see Getting to the ok Prompt on To cause the changes to take effect, type System Console OpenBoot Configuration Variable Settings Output-device Ttya Ttyb Screen Input-device Keyboard Netra 440 Server System Administration Guide August Managing RAS Features and System Firmware Alom System Controller Logging In To the Alom System Controller About the scadm Utility To Log In To the Alom System Controller To View Environmental Information Sc showenvironment Controlling the Locator LED To turn on the Locator LED, do one of the following To turn off the Locator LED, do one of the following OpenBoot Emergency Procedures Stop-N Functionality To Restore OpenBoot Configuration DefaultsStop-A Functionality Automatic System Recovery To reset the system, type the following commandStop-F Functionality Stop-D Functionality Auto-Boot Options Error Handling Summary Reset Scenarios Automatic System Recovery User CommandsEnabling and Disabling Automatic System Recovery To Enable Automatic System Recovery To cause the parameter change to take effect, type To Disable Automatic System RecoveryTo cause the parameter changes to take effect, type To Unconfigure a Device Manually Unconfiguring and Reconfiguring DevicesObtaining Automatic System Recovery Information To determine full physical device paths, type To Reconfigure a Device Manually To Enable the Hardware Watchdog Mechanism Enabling the Hardware Watchdog Mechanism and Its Options Multipathing Software Managing Disk Volumes Disk Volumes Sun StorEdge Traffic Manager Volume Management SoftwareVeritas Dynamic Multipathing Managing Disk Volumes RAID Technology Disk Concatenation RAID 0 Disk Striping RAID 1 Disk Mirroring Hot-Spares Hardware Disk MirroringRAID 5 Disk Striping With Parity To Create a Hardware Disk Mirror C1t3d0 Devices/pci@1f,700000/scsi@2/sd@3,0 For example To Delete a Hardware Disk Mirror To delete the volume, type the following command To confirm a failed disk, type the following command To Perform a Mirrored Disk Hot-Plug Operation To Perform a Non-Mirrored Disk Hot-SwapOperation View the status of the Scsi devices CD-ROM Remove the hard drive from the device tree # cfgadm -x removedevice c0dsk/c1t1d0 Configure the new hard drive Verify that the device has been removed from the device tree Verify that the new hard drive is in the device tree OpenBoot Configuration Variables Baudrate, bits Appendix a OpenBoot Configuration Variables Netra 440 Server System Administration Guide August Alarm Relay Output Application Programming Interface Netra 440 Server System Administration Guide August Page Netra 440 Server System Administration Guide August Page Netra 440 Server System Administration Guide August Symbols Index Netra 440 Server System Administration Guide August Asr-disable, 46 go Console, 11, 41 console -f, 9 poweroff, 12 poweron Uadmin 11 uname, 25 uname -r Netra 440 Server System Administration Guide August