Sun Microsystems 440 L, M, N, O, P

Index 79

Stop-F (non-USB keyboard sequence), 39

Stop-N (non-USB keyboard sequence), 39

L

L1-A keyboard sequence, 10, 11, 14

LEDs

Activity (disk drive LED), 65

Locator (system status LED), 37

OK-to-Remove (disk drive LED), 61, 64, 65

Locator (system status LED)

controlling, 37

controlling from sc> prompt, 37, 38

controlling from Solaris, 37, 38

logging in to the Advanced Lights Out Manager

(ALOM), 34

logical device name (disk drive), reference, 57

M

manual device reconfiguration, 48

manual device unconfiguration, 46

manual system reset, 12, 14

mirrored disk, 54

monitor, attaching, 29

multiple ALOM sessions, 9

Multiplexed I/O (MPxIO), 52

N

network management port (NET MGT)

activating, 17

conﬁguring IP address, 18

conﬁguring using Dynamic Host Conﬁguration

Protocol (DHCP), 17

non-mirrored disk hot-plug operation, 62

O

ok prompt

about, 9

accessing via ALOM break command, 10, 11

accessing via Break key, 10, 11

accessing via externally initiated reset (XIR), 12

accessing via graceful system shutdown, 11

accessing via L1-A (Stop-A) keys, 10, 11

accessing via manual system reset, 10, 12

risks in using, 12

suspension of Solaris operating environment, 12

ways to access, 10, 13

OK-to-Remove (disk drive LED), 61, 64, 65

OpenBoot commands

asr-disable, 46

go, 13

power-off, 21, 24, 27

probe-ide, 11

probe-scsi, 11

probe-scsi-all, 11

reset-all, 30, 45, 48

set-defaults, 41

setenv, 21, 29

show-devs, 47

showenv, 67

OpenBoot configuration variables

auto-boot, 10, 42

described, table, 67

diag-device, 43

error-reset-recovery, 49

input-device, 21, 29, 31

output-device, 21, 29, 31

system console settings, 31

ttyb-mode, 28

OpenBoot emergency procedures

non-USB keyboard commands, 39

performing, 39

USB keyboard commands, 40

OpenBoot firmware

scenarios for control, 10

operating environment software, suspending, 12

output-device (OpenBoot configuration

variable), 21, 29, 31

P

parity, 26, 28, 56

patch panel, terminal server connection, 19

PCI cards

device names, 47

frame buffers, 29

Contents

Main Page Contents Page Page Page Figures Page Tables Page Preface How This Book Is Organized Using UNIX Commands Shell Prompts Typographic Conventions Related Documentation AaBbCc123 Page Configuring the System Console Communicating With the System Page What the System Console Does Using the System Console Default System Console Connection Through the Serial Management and Network Management Ports Page Alternative System Console Configuration Accessing the System Console Through a Graphics Monitor Note About the sc> Prompt Note Access Through Multiple Controller Sessions Reaching the sc> Prompt OpenBoot ok Prompt Reaching the ok Prompt Graceful Shutdown ALOM System Controller break or console Command L1-A (Stop-A) Keys or Break Key Note Externally Initiated Reset (XIR) Caution Manual System Reset Caution Getting to the ok Prompt Caution To Get to the ok Prompt Switching Between the ALOM System Controller and the System Console Note Accessing the System Controller Using the Serial Management Port To Use the Serial Management Port Activating the Network Management Port Note To Activate the Network Management Port Accessing the System Console Through a Terminal Server To Access The System Console Through a Terminal Server Page Note Accessing the System Console Through a TIP Connection To Access the System Console Through the TIP Connection Note Modifying the /etc/remote File To Modify the /etc/remote File Note Accessing the System Console Through an Alphanumeric Terminal To Access the System Console Through an Alphanumeric Terminal Note Verifying Serial Port Settings on TTYB Note To Verify the Serial Port Settings on TTYB Accessing the System Console Through a Local Graphics Monitor To Access the System Console Through a Local Graphics Monitor Page System Console OpenBoot Configuration Variable Settings Page Managing RAS Features and System Firmware Note ALOM System Controller Note Logging In To the ALOM System Controller Note To Log In To the ALOM System Controller About the scadm Utility Note To View Environmental Information Note Controlling the Locator LED Note OpenBoot Emergency Procedures OpenBoot Emergency Procedures for Systems With Non-USB Keyboards OpenBoot Emergency Procedures for Systems With USB Keyboards Stop-A Functionality Stop-N Functionality To Restore OpenBoot Configuration Defaults Stop-F Functionality Automatic System Recovery Note Auto-Boot Options Note Error Handling Summary Note Reset Scenarios Automatic System Recovery User Commands Enabling and Disabling Automatic System Recovery To Enable Automatic System Recovery Note To Disable Automatic System Recovery Note Obtaining Automatic System Recovery Information Unconfiguring and Reconfiguring Devices To Unconfigure a Device Manually Page Note To Reconfigure a Device Manually Note Enabling the Hardware Watchdog Mechanism and Its Options To Enable the Hardware Watchdog Mechanism Multipathing Software Managing Disk Volumes Disk Volumes Volume Management Software VERITAS Dynamic Multipathing Sun StorEdge Traffic Manager Note RAID Technology Disk Concatenation RAID 0: Disk Striping RAID 1: Disk Mirroring RAID 5: Disk Striping With Parity Hot-Spares Hardware Disk Mirroring Caution Physical Disk Slot Numbers, Physical Device Names, and Logical Device Names To Create a Hardware Disk Mirror Page To Delete a Hardware Disk Mirror Page To Perform a Mirrored Disk Hot-Plug Operation Caution Note To Perform a Non-Mirrored Disk Hot-Swap Operation Page Page Page Note that c1t3d0 is now listed as configured. OpenBoot Configuration Variables Page Page Page Alarm Relay Output Application Programming Interface Page Page Page Page Page Index SYMBOLS A B C D E F G H L M N O P R S T U V X