Manuals / Sunwave Tech / TV and Video / Universal Remote

Sunwave Tech SRC-7000 manual Install Upgrade Tools, Install USB Cable and Software

Models: SRC-7000

1 75

Download 75 pages 52.85 Kb

Page 65

5.2 Install Upgrade Tools

Chapter 5 Install USB Cable and Software

5.2 Install Upgrade Tools

The Upgrade Tools enable you to upgrade your firmware and pre- programmed codes through the internet.

1.Locate the program from the CD enclosed with the package or download the program from http://www.sun-wave.com

2.Double click the icon below to install Upgrade Tools, and you will see the window below. Click “Next” to continue.

3.Choose the directory you wish the program to be installed into then click “Next”.

63

Image 65

Sunwave Tech SRC-7000 manual Install Upgrade Tools, Install USB Cable and Software

Contents

SRC-7000 Touch Screen Smart Remote ControlUser’s Manual 041201About this manual PrefaceCopyright TrademarksTable of Contents Chapter 3 How to Set Up Your SRC-7000 Chapter 4 Menus Chapter 1 Introduction to the SRC-7000 Chapter 1 Introduction to the SRC-7000 1.1 SRC-7000 Features1.2 Unpacking the SRC-7000 SRC-7000 User’s Manual 1.3 Battery InstallationChapter 1 Introduction to the SRC-7000 1.3.1 Battery Precautions1.4 Turning the Touch Screen On 1.5.1 Top of SRC-7000 1.5 Identifying ComponentsSRC-7000 User’s Manual 1. Light sensor P.542. Reset switch 1.5.2 Botton of SRC-70005. Battery compartment Chapter 1 Introduction to the SRC-7000SRC-7000 User’s Manual 1.5.3 Direct Access Buttons Rubber KeysChapter 1 Introduction to the SRC-7000 1.5.5 Precautions When Using the Touch Screen1.5.4 LCD Touch Screen Figure 1-6 Touch screen buttons 1.5.6 Touch Screen KeysSRC-7000 User’s Manual y Device Layout y Main MenuIntroducing the frequently used LCD Layout as followed Chapter 1 Introduction to the SRC-7000SRC-7000 User’s Manual y Timer Macro Layouty Basic Information Layout When you are under the setup status you will see the icons as follows y Setup Menu LayoutKey Layout Setup Mode Code Setting Setup ModeSRC-7000 User’s Manual Timer Macro Setup Mode2.1 Re-calibrating the Screen Chapter 2 Quick StartSRC-7000 User’s Manual 2.2 Date / Time SettingChapter 2 Quick Start 2.3 Device Setting4. Finally, press the button to load the code and exit SRC-7000 User’s Manual3.1.1 Create a New Device Chapter 3 How to Set Up Your SRC-70003.1 Add a Device Next row SRC-7000 User’s ManualA. Pre-code 3.1.2 Load the Codes for the Newly-added DeviceChapter 3 How to Set Up Your SRC-7000 SRC-7000 User’s Manual B. Learning Chapter 3 How to Set Up Your SRC-7000Figure 3-1 Using the Learning Eye SRC-7000 User’s Manual Chapter 3 How to Set Up Your SRC-7000 3.2 Add a Soft KeySRC-7000 User’s Manual Chapter 3 How to Set Up Your SRC-7000 3.3 Adding TextSRC-7000 User’s Manual 3.4 Re-label a Device, Key or Text3. Please select the device you want to rename Chapter 3 How to Set Up Your SRC-7000SRC-7000 User’s Manual 3.5 Re-size a Device, Key or TextThe way to re-size a soft key is similar to the way to add a soft key 3.6 Delete a Device, Key or TextChapter 3 How to Set Up Your SRC-7000 5. If you select a device to delete, you will see a message to confirm SRC-7000 User’s ManualChapter 3 How to Set Up Your SRC-7000 3.7 Pre-programmed CodeSRC-7000 User’s Manual Using the Learning Eye 3.8 LearningChapter 3 How to Set Up Your SRC-7000 SRC-7000 User’s Manual Learning fail Chapter 3 How to Set Up Your SRC-7000Learning successfully SRC-7000 User’s Manual 3.9 Learn a Cycle KeyChapter 3 How to Set Up Your SRC-7000 3.10 Delete Device / Key CodesSRC-7000 User’s Manual 3.11 Create a Macro3.11.1 Macro b. to go back to the former command you selected Chapter 3 How to Set Up Your SRC-7000a. to set up the delay between two commands from 0 ~30 seconds SRC-7000 User’s Manual An Example of setting a MacroThe Basic Device The Required Macro SequenceChapter 3 How to Set Up Your SRC-7000 3.11.2 Timer MacroA. Create a Timer Macro 5. Select the operation processes between any devices SRC-7000 User’s ManualChapter 3 How to Set Up Your SRC-7000 B. Delete Your Timer MacroIf you delete the Timer Macro, you will erase the Timer along with it at the same timeSRC-7000 User’s Manual C. Re-label Your Timer MacroChapter 3 How to Set Up Your SRC-7000 D. View Your Timer MacroSRC-7000 User’s Manual 3.12 Set Up Your Favorite Channels3.12.1 Add Favorite Channel Keys Chapter 3 How to Set Up Your SRC-7000 3.12.2 Set Your Favorite Channels as MacrosChapter 4 Menus 4.1 Set Up the RemoteTime PowerContrast Chapter 4 MenusLight Sensitivity LCD OffLight Period SRC-7000 User’s ManualChapter 4 Menus ResetMotion Add Device 4.2 Key LayoutAdd Key Add TextPre-code 4.3 Code SettingLearning MacroDelete 4.4 Timer MacroRe-label ViewChapter 4 Menus 4.5 DuplicateDuplicate a. The cable is properly connected at both ends b. The batteries in both remotes with sufficient powerSRC-7000 User’s Manual 5.1.1 Install the SLC-2080 USB Driver Chapter 5 Install USB Cable and Software5.1 Introduce SLC-2080 USB Cable Chapter 5 Install USB Cable and SoftwareSRC-7000 User’s Manual The SLC-2080 USB driver is installed completelyChapter 5 Install USB Cable and Software 5.2 Install Upgrade ToolsSRC-7000 User’s Manual 4. Choose a Start menu folder for your Upgrade Tools shortcuts then click “Next”Chapter 5 Install USB Cable and Software SRC-7000 User’s Manual 5.3 Upgrade VMCU Firmware and VMCF Pre- programmed CodesBackup Remote Chapter 5 Install USB Cable and SoftwareFrom Internet From File7. You will see “OK” message after completion SRC-7000 User’s ManualAppendix A FeaturesModel Battery Dimensions WxHxD Weight Keys Display LCD Resolution SpecificationsPower Management Interface Optional Accessories Power Consumption SRC-7000 User’s ManualAppendix B Optional AccessoriesSLC-2080 USB CableAppendix C Troubleshooting TablesYou see an “error” display