How to label a configuration slot

Config Menu ⇒ Configurations

•Make sure the printer is Offline.

•Press the Menu key to enter Menu mode.

•Use the Up and Down Arrow keys to get to the Config menu, and then press Enter.

•Use the Up and Down Arrow keys until the display reads Configura- tions, then press Enter.

•Use the Up and Down Arrow keys until you see Config n label, where n is the number of the configuration you want to label (1-10). Press Enter.

•A cursor appears underneath the first letter (C). Use the Up and Down Arrow keys to scroll to the number or letter you want to use. Repeat for up to 15 characters, pressing Enter after each letter. You must press Enter 15 times even if your label is shorter.

•Press Clear or Menu to save it. Now, when you use SAVE or LOAD, this configuration name appears in the slot you've chosen.

Chapter 3: Printer Menus and the Control Panel 3–59

Page 59

Image 59

Tally Genicom 2900 manual How to label a configuration slot

Contents

Operator Manual Operator Manual Serial Parallel LAN Acknowledgments Contents Chapter Operator Manual ESC Appendix a Troubleshooting Appendix B Specifications Operator Manual Preface-9 Introduction Conventions About This ManualPreface-10Operator Manual Site Preparation Setting Up Your Printer Removing the Shipping Hardware Unpacking the PrinterUnpacking your printer Repacking Serial/Parallel Interfaces Interface Connections and Powering UpInterface Connectors Interface Connections 14Operator Manual Powering UpPowering Up Paper System Components Paper SystemPaper System Components Paper Tension 16Operator ManualTractors Print Gap Installing the Ribbon Cartridge Installing Ribbon Cartridge 18Operator Manual LCD Liquid Crystal Display LED IndicatorsControl Panel Components Control Panel Components 20Operator Manual Loading Paper and Printing 22Operator Manual Standard Printing ModeLoading Paper for Standard Printing Mode Step Column Alignment Scale 24Operator Manual Gap Zone Print Gap AdjustmentPrint Gap Profile Mode Print Gap 26Operator Manual Using a Saved Gap Zone ProfileFine-tuning the Automatic Print Gap Setting After unlocking the Print Gap keys Set Print Gap Detect Mode to ManualManually Adjust Print Gap on Control Panel Run a Print Test Manually Setting Print GapSetting Up Configurations 28Operator Manual Printer Menus and the Control Panel Control Panel Display 30Operator Manual Control Panel DisplayDisplay During Normal Operation Display When In a Menu Indicator Paper Weight and Hammer Impact 32Operator Manual Control Panel Key FunctionsControl Panel Key Functions Up and Down Arrow Keys TOF Key Top of FormView Key Print GAP + and Keys 34Operator Manual Enter KeyClear Key Offline Clear Key Config Key Categories, Parameters and Selections Using MenusUsing Menus Control Panel Menus TCP/IP if LAN is installed 38Operator Manual Example Changing Form Length Using the Menu SystemChanging Form Length Print Selections Report How to Print a Control Panel Selected Options Report 40Operator Manual Operator MenuOperator Menu ⇒ Font Font Category Ocra Density Ser/Par Character SetMatrix 42Operator Manual Forms Category 44Operator Manual Operator Menu ⇒ Forms Eject Distance Quick AccessPrint to EOF End Of Form If Print to EOF is on If Print to EOF is OFF, you have two choices Choice 46Operator Manual Ribbon Monitor Operation RibnMon Thresh 48Operator Manual Operator Menu ⇒ Print GapPrint Gap Category Mode Fine-Tuning the Print Gap ManuallyReset Detect Distance 50Operator Manual VT Channel Vertical Tab Channel VFU EnableOperator Menu ⇒ VFU VFU Category Vertical Format Units 52Operator Manual Config MenuConfig Menu ⇒ Printer Printer Category Report IO Hold 54Operator Manual Beeper ModeBeeper Volume Codes Category Config Menu ⇒ Codes Alt ESC Alternate Escape 56Operator ManualPrint on CR Form Feed at TOF Sub Char From Code 7FPrint 80 9F Hex Ignore Char 58Operator Manual Config Menu ⇒ ConfigurationsConfigurations Category How to label a configuration slot 60Operator Manual Config Menu ⇒ Serial I/OSerial I/O Category DTR Function Status Enquiry RTS Function 62Operator ManualDTR Polarity Busy Polarity Bi-Directional Config Menu ⇒ Parallel I/OPopc Print On Paper Command Parallel I/O Category Serial Parallel Twinax/Coax Config Menu ⇒ IntellifilterIntellifilter Category 64Operator Manual Gateway Category TCP/IP Menu LAN Interface OnlyTCP/IP Menu IP Addr Category 66Operator Manual TCP/IP Menu ⇒ SubnetSubnet Category Print Test MenuTestMenu ⇒ Pattern Pattern Category 68Operator Manual Test Menu ⇒ Fault OverrideFault Override Category Diag Category Help Menu Help Menu 70Operator Manual Messages FaultsAppendix a Troubleshooting A-71 Fault Correction Procedure 72Operator Manual Error Messages HammerTimeExplanation Corrective Action Appendix a Troubleshooting A-73 74Operator Manual Appendix a Troubleshooting A-75 76Operator Manual Paper Problems Industry and Agency Standards Appendix B Specifications B-77 78Operator Manual Industry and Agency Standards Environment Appendix B Specifications B-79 80Operator Manual Emulations and Fonts Language Substitutions Appendix B Specifications B-81Fonts, Languages and Characters Standard Languages and Character Sets 82Operator Manual Configurations, Paper and Speed Appendix B Specifications B-83 Daly Drive, Suite 703.833.8700 Chantilly, VA 703.222.7629