Industry and Agency Standards | Tally Genicom 2900 specs

Industry and Agency Standards

Physical Configurations

Weight

115.4 lbs.
Dimensions
Width:	28.3 inches
Height:	13.0 inches
Depth:	14.4 inches
Depth with paper exit guide assembly:		23.4 inches

Preventive Maintenance

This printer is designed to eliminate the requirement of scheduled mainte- nance procedures, such as alignment, adjustment, or lubrication. Preventive maintenance is limited to periodic cleaning. Dust and paper fibers should be removed periodically with a soft cloth and brush or a vacuum cleaner. Clean the printer case with a damp cloth and soapy water. DO NOT use any abrasive cleaners or solvents, as they will damage the case.

Environment

Operating
Temperature (Dry Bulb):		50°F to 104°F (10°C to 40°C)
Humidity:	10 to 90% noncondensing with a maximum wet bulb
	temperature of 82°F (28°C) and a minimum dew point of
	36°F (2°C )
Altitude:	To 8,000 ft. (2438 meters)

Nonoperating
Temperature:
Boxed:	-40°F to 151°F (-40°C to 66°C)
Unboxed:	14°F to 122°F (-10°C to 50°C)
Humidity:	10 to 95% noncondensing
Altitude:	To 10,000 ft. (3048 meters)
Thermal Shock:	61°F (20°C) per hour
Vibration:	Units meet NSTA (National Safe Transit Association)
	requirements.

Safety

Personnel hazard areas have restricted access with appropriate warning labels. Catastrophic equipment failures are inhibited with protective functions in major areas of overload potential.

B–78Operator Manual

Image 78

Tally Genicom 2900 manual Industry and Agency Standards, 78Operator Manual

Contents

Operator Manual Serial Parallel LAN Operator Manual Acknowledgments Contents Chapter Operator Manual ESC Appendix a Troubleshooting Appendix B Specifications Introduction Operator Manual Preface-9 About This Manual Preface-10Operator ManualConventions Setting Up Your Printer Site Preparation Repacking Unpacking the PrinterUnpacking your printer Removing the Shipping Hardware Interface Connections Interface Connections and Powering UpInterface Connectors Serial/Parallel Interfaces Powering Up Powering Up14Operator Manual Paper System Paper System ComponentsPaper System Components Print Gap 16Operator ManualTractors Paper Tension Installing Ribbon Cartridge Installing the Ribbon Cartridge 18Operator Manual Control Panel Components LED IndicatorsControl Panel Components LCD Liquid Crystal Display 20Operator Manual Loading Paper and Printing Standard Printing Mode Loading Paper for Standard Printing Mode Step22Operator Manual Column Alignment Scale 24Operator Manual Print Gap Print Gap AdjustmentPrint Gap Profile Mode Gap Zone Using a Saved Gap Zone Profile Fine-tuning the Automatic Print Gap Setting26Operator Manual Set Print Gap Detect Mode to Manual Manually Adjust Print Gap on Control PanelAfter unlocking the Print Gap keys 28Operator Manual Manually Setting Print GapSetting Up Configurations Run a Print Test Control Panel Display Printer Menus and the Control Panel Control Panel Display Display During Normal Operation30Operator Manual Indicator Paper Weight and Hammer Impact Display When In a Menu Control Panel Key Functions Control Panel Key Functions32Operator Manual Print GAP + and Keys TOF Key Top of FormView Key Up and Down Arrow Keys Enter Key Clear Key34Operator Manual Clear Key Config Key Offline Control Panel Menus Using MenusUsing Menus Categories, Parameters and Selections TCP/IP if LAN is installed Example Changing Form Length Using the Menu System Changing Form Length38Operator Manual How to Print a Control Panel Selected Options Report Print Selections Report Font Category Operator MenuOperator Menu ⇒ Font 40Operator Manual Ser/Par Character Set MatrixOcra Density 42Operator Manual Forms Category Operator Menu ⇒ Forms 44Operator Manual If Print to EOF is OFF, you have two choices Choice Quick AccessPrint to EOF End Of Form If Print to EOF is on Eject Distance 46Operator Manual RibnMon Thresh Ribbon Monitor Operation Operator Menu ⇒ Print Gap Print Gap Category48Operator Manual Fine-Tuning the Print Gap Manually ResetMode 50Operator Manual Detect Distance VFU Category Vertical Format Units VFU EnableOperator Menu ⇒ VFU VT Channel Vertical Tab Channel Printer Category Config MenuConfig Menu ⇒ Printer 52Operator Manual IO Hold Report Beeper Mode Beeper Volume54Operator Manual Config Menu ⇒ Codes Codes Category Form Feed at TOF 56Operator ManualPrint on CR Alt ESC Alternate Escape Ignore Char Code 7FPrint 80 9F Hex Sub Char From Config Menu ⇒ Configurations Configurations Category58Operator Manual How to label a configuration slot Config Menu ⇒ Serial I/O Serial I/O Category60Operator Manual Status Enquiry DTR Function Busy Polarity 62Operator ManualDTR Polarity RTS Function Parallel I/O Category Config Menu ⇒ Parallel I/OPopc Print On Paper Command Bi-Directional 64Operator Manual Config Menu ⇒ IntellifilterIntellifilter Category Serial Parallel Twinax/Coax IP Addr Category TCP/IP Menu LAN Interface OnlyTCP/IP Menu Gateway Category TCP/IP Menu ⇒ Subnet Subnet Category66Operator Manual Pattern Category Test MenuTestMenu ⇒ Pattern Print Diag Category Test Menu ⇒ Fault OverrideFault Override Category 68Operator Manual Help Menu Help Menu 70Operator Manual Fault Correction Procedure FaultsAppendix a Troubleshooting A-71 Messages Error Messages 72Operator Manual Appendix a Troubleshooting A-73 HammerTimeExplanation Corrective Action 74Operator Manual Appendix a Troubleshooting A-75 Paper Problems 76Operator Manual Appendix B Specifications B-77 Industry and Agency Standards Industry and Agency Standards 78Operator Manual Appendix B Specifications B-79 Environment Emulations and Fonts 80Operator Manual Standard Languages and Character Sets Appendix B Specifications B-81Fonts, Languages and Characters Language Substitutions Configurations, Paper and Speed 82Operator Manual Appendix B Specifications B-83 Daly Drive, Suite 703.833.8700 Chantilly, VA 703.222.7629