General Codec Configuration | TANDBERG D5016402 guide

Getting Started	TANDBERG Director Videoconferencing System

General Codec Configuration

The control system communicates with the codec through Data 1 at 9600 baud, No parity bit, 8 data bits, and 1 stop bit. The codec should be left in its default configuration with the following exceptions. Using the IR control, the following settings should be addressed:

N O T E

THESE SETTINGS ARE ESSENTIAL FOR OPTIMAL SYSTEM SETUP.

•Enabled but unused ISDN lines (lines not active) should be disabled.

•Select the QUICK KEY ‘System Info’ (IR control) to view line status.

•To disable unused ISDN lines, press MENU on the remote control.

•Select the menu ‘Terminal Settings’ > ‘Network’ > ‘ISDN-BRI settings’.

•Select the relevant ‘Line Setup’ menu and set ‘Enabled: Off’.

•Enter System Name to identify the system during an MCU conference.

•Select ‘Utilities’ > ‘System Name’

•Enter the name using the NUMBER KEYS (as on a mobile phone).

•Select the language you want to use in ‘Terminal Settings’ > ‘Language’.

•If you are using two monitors, set ‘Utilities’ > ‘Dual Monitor: On’.

•To activate AES Encryption, MultiSiteTF and/or Presenter, enter an option key (see paperwork accompanying your system). See ‘Terminal Settings’ > ‘Software Options’.

•Press CONNECT on the IR control. A dial tone should be heard if the network is active.

•Using the monitor remote control, adjust the VOLUME on the monitor to a level of your choice. This volume will be the default volume for all calls.

It is critical that the following settings are configured:

•All network and LAN information (SPIDS, IP Addresses, etc. )

•DuoVideo Mode “Manual”

TF - TANDBERG FIRST

34

Image 34

TANDBERG D5016402 user manual General Codec Configuration

Contents

Director Page Disclaimer Environmental IssuesTrademarks and copyright Production of products Other Warnings and Safety Precautions Important Information Tandberg Director Videoconferencing System Contents Tandberg Director Videoconferencing System Introduction Welcome to the Tandberg Director At a Glance The Tandberg Director Wave Control Interface System OverviewAudio and Video Sources Optional Equipment System Connections Rear Interface Panel Rear Interface Panel Connections Rear Interface Panel A/V Plate Installation & Setup Room Configuration Installing the Guest Laptop Shelf Guest laptop shelf Installing the Adjustable Camera Shelf To install the videoconferencing shelf T E Tandberg Director Videoconferencing System Camera S-VID OUT Camera Ctrl OUT System Setup Powering on the SystemSmart BoardTM Projector Setup and Calibration Touchscreen Calibration Touch Panel Tools for System Configuration System Information IR Functions Audio System Options Update DirectoryEdit Directory Other Networks Using the External Network Interface Network Connections Touch Panel Device ConnectionsMicrophone Main Camera PC and Laptop Computer Setup Laptop PC Calibration System startup Getting StartedControl Orientation Touch Screen and Remote IR Controls ‘IR Controls’ will appear in the place of the ‘Address Book’ Codec Basics Menu structure General Codec Configuration Isdn configuration Network and LAN SettingsLAN configuration DUOVideoTF Mode Microphone on/off Adjusting volumeGeneral use Directory Projector Standby Button LED MultiSiteTF MCU LAN 3MB Establishing MultiSiteTF meetings using Directory MultiSiteTF cascading Text Chat / Closed Captioning PC SoftPresenterWeb-interface Streaming Local Display Operation Display OperationScreen Basics Source Selection Device Control Taskbar Video Display Window Making Calls When the Director receives/initiates a video/audio callVideoconference Operation Speed Dialing Will attempt to call the last manually dialed number Disconnecting a CallManual Dialing Back button to exit from this screen Editing Speed Dial Directory Creating a new speed dial number Making a MultiSiteTF Call On Screen SymbolsEditing an existing speed dial number Videoconference Main Screen Video Window Display Control Videoconferencing Taskbar PIP Far End Camera Control Source DuoVideoTF Operation Task23456789Bar Multipoint Operation Advanced use Menu PasswordMain menu Video VGA ResolutionsCall quality Natural Video Advanced call quality Presentations Presentation ModeDuoVideo Mode DuoVideo Quality Utilities Welcome Menu Dual MonitorAuto-PIP Continuous Presence MCU services Quick Menu Terminal Names Request floorRelease floor View site # Chair control Audio Settings Audio Inputs Mix Mode Level Settings Inputs Level Settings Outputs Audio Outputs Room Size Echo ControlNoise Reduction Motion Automatic Gain Control AGC Settings Tips for improving the echo canceller performance Restore Audio Defaults Video SettingsAlert Tones & Volume Camera Tracking Mode Brightness FocusWhitebalance VGA Out VGA SettingsVideo Name VGA Out Quality Start using VNC VNC SettingsPassword Address Terminal Settings Network Configuration Isdn switch type ISDN-BRI SettingsLine setup Advanced Isdn settings Subaddress Example ISDN-PRI Settings PRI Switch Type Channel Hunting Advanced Isdn Settings Line SettingsAdvanced ISDN-PRI Settings Max Channels Leased E1/T1 SettingsNetwork Interface Start Channel External network settings Call control Cable Specification 35/RS-366 cable Network clocking Address Port LAN SettingsTTL/Router Hops Allow Remote Start How to view streamingStreaming Source Announcements Settings Advanced H.323 Settings IP Precedence IP Type of Service TOSTells the router to minimize the delay Tells the router to maximize the reliability IP Settings Incoming MCU calls Call SettingsSnmp Settings Snmp Trap Host Fallback to telephony Access CodeIncoming telephone calls Encryption Secure Conference Max Call Length Encryption ModeNetwork Profiles Dataport configuration Dataport Software Options LanguageFollowing options are available System info DiagnosticsChannel status Call status Cause codes Far End Loop Isdn only Restore defaultsView Current Settings System Selftest Appendices Connecting Appendix 1 Connecting to Isdn using network adaptersConfiguring Configuration of Telesync Adapter Appendix 2 Connecting to the Switched 56 networkUsing Telesync TS-256 SW56/ISDN adapter Configuration of the system Connecting to Adtran T1 ESF CSU ACE Appendix 3 Connecting to PRI/T1Using CSU adapter Configuration of Adtran T1 ESF CSU ACE Appendix 4 Environmental & operational considerations Guidelines for Optimal Videoconferencing Environments Iris Control and Lighting Brightness Control Loudspeaker VolumeBackground Appendix 5 Using the file system Description of the different files Streaming Password Access CodeMenu Password IP Password Snmp Security alert ServicesEncryption Appendix 7 12 Touch Panel Interface Local Display Operation 105 106 2323 Videoconference Operation 234 2345678 Video Features Technical Description 111 Abbreviations Symbols Index 114 115 Servicing Canada