Toshiba TF831/861 Line 2 mode (option)

102

GB

Advanced settings

Advanced settings TOSHIBA TF 831/861

Line 2 mode (option)

If the second line (option) is installed in

your fax machine, you can use a different

configuration for this second line:

setting:

TX/RX

RECEPTION ONLY

TIMER

Practical information:

The second line is also used as a trans-

mission line by the fax machine. If you

have a large number of fax documents

to transmit (e.g. in the event of exten-

sive broadcasts) and if you need to

transmit these fax documents as

quickly as possible, then you should

select this setting.

If your fax machine should be reach-

able at all times, you can reserve the

second line exclusively for receiving fax

documents. In this case, documents

are transmitted only via line 1.

This setting is a combination mode for

the second line. Outside the defined

period, the second line has the same

priority as line 1 (see first setting).

Within the defined period, it is used

exclusively used for receiving docu-

ments (see second setting).

Effect:

The second line has

the same priority as

line 1.

The second line is

used exclusively as

the receiving line.

During a user-defin-

able period, the sec-

ond line can be re-

stricted to be a pure

reception line.

Use the fax function “TEL LINE

SELECT” to temporarily

circumvent these settings.

15-03-97 SAT 19:56

TRANSMIT AV AILABLE

LOAD DOCUMENT

RESIDUAL MEMORY 100 %

1.COMM. OPTION S

2.LISTS

3.INSTALLATION

4.MENU LIST

//

LINE-2 MODE

1.TX/RX

2.RECEPTION ONLY

3.TIMER

TIME PERIOD =

RECEPTION ONLY

00:00 - 00:00

START

Standby mode

Start the menu

The first 4 menu items are displayed.

Select a menu item

Make your selection

for line 2 mode

(Example: TIMER)

Select a menu item

Make your selection

for period “only receiving line”

Enter the new period

confirm with START

Press STOP, return to standby

mode

STOP

Contents

Main Welcome to your fax machine TOSHIBATF 831/861 Contents Preparation Installation Reception of documents Transmit documents Unpacking Remove transport fittings: How to install the process unit: Open the top cover Install the process unit... To make a good impression: the toner pack Connection to the mains Page Insert memory card(s) The menu system or or 11 Installation Enter user name User name: Place character: Replace character: Insert character: Enter the name Continue with Enter the terminal ID 13 Installation Enter terminal ID Continued from Enter user name Now enter the code Setting dialling method 15 A Connection to PABX, obtaining a public line Set language 17 Set date and time Set standby mode Automatic reception Manual reception To set reception mode do the following: Enter the required number 19 Reception reduction Memory reception 21 SECURE RX Go to BGo to A2Go to A1 A1 Enter the security code A2 Enter the old security code Enter the new security code B Activate and deactivate Secure Rx 25 Correct sequence print- out Multiple printout 27 Delete reception (again) Reception protection 29 Local copy Sorter function OFF Sorter function ON Press COPY key / / 31 TOSHIBATF 831/861 Document format Please note: Problem documents ... Automatic fax mes- sages Enter the fax number LINE x is lit 33 Stack mode This is different with your fax ma- chine: Useful job management 35 Important transmission Direct transmission 37 Activate alphabet dial Enter the alphabet dial number Transmission using alpha dial Transmission one-touch dial Press the one-touch dial key 39 Faxing with telephone directory *) Activate directory function Enter the alphabet dial number Single multi-address transmission Press the MULTI key 41 Stored broadcast Broadcast via group number Press the SPEED DIAL key 3 times Enter group number Monitoring (direkt) Activate monitoring Enter the fax number ...confirm with START 43 Monitoring (Job) Set resolution Press MODE Dialling the fax partners 45 Set contrast Dialling the fax partner ECM on/off Dialling the fax partner 47 number of pages protected transmission 49 reduced speed send cover sheet 51 transmission stamp (if installed) Chain dialing 53 Redial Manual call redial (from memory): Manual call redial (from document feed): Manual call redial (from memory) Resend (retained job) corresponding function key * activate. Selection 1: Job is activated unchanged Selection 2: Change the current fax number 55 Cancel a retained job (with retain job) Cancel transmission The job is displayed as follows: Cancel job during direct transmission Press STOP Cancel from stack 57 Reserve polling Polling reserved Connection established End of polling. General: Reserve polling Polling protection Reserve single polling Enter the number 59 Reserve polling, perma- nent (general infobox) Reserve permanent polling (Infobox) Reserve polling, append documents Add documents 61 TOSHIBATF 831/861 Cancel polling reserva- tion Single polling Enter the fax number of the fax machine from which you wish to poll B 63 Multiple polling Go to B Go to A Press the MULTI key B 65 Cancel polling Program Continous Polling Enter... R Reverse direction Enter the menu Page Alphabet dial memory Page Alphabet dial options Delayed Comm Journal Listening-in Low Speed TX 73 Store numbers Modify ABB numbers Procedure as described under Enter alphabet dial number: See page 70 Delete ABB numbers 75 33335 Store numbers One-touch dial keys SHIFT Page 77 Cancel one-touch dial keys 3333335 Define groups Define groups Enter group number Page Edit groups Refer to page 78 for procedure as described under Define groups Enter an alphabet dial number 81 Cancel groups Program selection list Transmission reports 83 TOSHIBATF 831/861 The various transmission reports and related options: Transmission report: Memory TX report: Select the entry which you wish to print. Press the COPY/JOURNAL key Multi transmission report: 85 Transmission and reception journal *) For manual output Report prints TOSHIBA TF 831/861 Reservation list The function list 87 TRANSMIT AVAILABL E LOAD DOCUMENT SHIFT TEL LIST PRINT The required list(s) are printed out The dial number lists Department list Mains failure report TRANSMIT AV AILABLE LOAD DOCUMENT 1.COMM. OPTION S 2.LISTS 3.INSTALLATION 4.MENU LIST 89 Delayed fax job Set transmission header position 91 Reception trailer (RTI) Permanent monitoring Call redial A B 93 Set ringer volume Power saver (stand by) Enter the period 95 Cost centre manage- ment Enter the department name Department code 97 Modify or delete a department Disable department code 99 Cover sheet Insert required cover sheet docu- ment Retain jobs Input retaining time 101 Query job status The LINE lamp lights up and indi- cates activity on the line (again) Line 2 mode (option) Enter the new period 103 Basic setting, document length Basic setting, transmis- sion memory Basic setting, resolution and contrast 105 Basic setting, ECM (er- ror correction mode) Basic setting, protected transmission Basic setting, TX stamp (option) Basic setting, superfine reception (only TF 861) 107 Additional paper cas- settes (optional) Divider sheet Diagnosis programs Key panel: STOP Print unit: TRANSMIT AVAILABL E LOAD DOCUMENT 109 B STOP PRINT TEST 1.PATTERN 1 2.PATTERN 2 Error messages in the display Display 111 Error codes in journal Code 113 ... and solutions Problem Possible causes ... Transmission problems Receiving problems 115 Cleaning document scanner Document jam How to clear a recording paper jam After opening Filling the stamp ink 117 Remote maintenance (COMLINE) Connection to PABX UK Connection information Index Index