Yamaha RX-V4600 Setting remote control AMP codes, Setting remote control tuner codes, Press Enter

REMOTE CONTROL FEATURES

3Press and hold LEARN for about 3 seconds using a ballpoint pen or similar object.

The library name (ex. “L:DVD”) and the selected component name (ex. “DVD”) appear alternately in the display window.

LEARN

y

If you want to setup for another component, press the input selector button or SELECT k / n to select the component.

Notes

•Be sure to press and hold LEARN for at least 3 seconds, otherwise the learning process will start.

•If you do not complete each of the following steps within 30 seconds, the setting mode will be automatically canceled. In this case, press LEARN again.

If you want to change a library (component category), press l / h. You can set a different type of component.

Library choices: L:DVD, L:DVR, L:LD, L;CD, L:CDR, L:MD, L:TAP (tape), L:TUN (tuner), L;AMP*, L:TV, L:CAB (cable), L:SAT (satellite), L:VCR

*The amplifier library (L;AMP) code is preset to “2000” in order to operate this unit. However, you can switch by entering one of the following 4 codes if necessary.

Setting remote control AMP codes

Select one of the following codes to set the remote control AMP code for the component you want to use.

Set AMP/SOURCE/TV to AMP or SOURCE, then change the remote control code settings.

AMP library		Remote
		control
code
	Function	AMP ID
(remote
		(this unit’s
control
		setting:
setting)
		see page 86)
2000	To operate this unit using
(initial setting)	the default code.
		ID1
	To operate this unit using
2001	the default code.	(initial setting)
	To operate Zone 2 or Zone 3
	features (see page 82).
2002	To operate this unit using an
	alternative code.
	To operate this unit using an
	alternative code.	ID2
2003	To operate Zone 2 or Zone 3
	features of other YAMAHA
	receivers/amplifiers
	(see page 82).

Setting remote control tuner codes

Select one of the following codes to set the remote control tuner code for the component you want to use.

Set AMP/SOURCE/TV to SOURCE and the unit to the tuner mode by pressing TUNER on the remote control, then change the remote control code settings.

Tuner		Remote
		control
library code
	Function	tuner ID
(remote
		(this unit’s
control
		setting:
setting)
		see page 86)
2602	To operate this unit using	ID1
(initial setting)	the default code.	(initial setting)
2603	To operate this unit using an	ID2
	alternative code.

Note

When using multiple YAMAHA receivers/amplifiers, you may be able to operate the other components simultaneously with the default code setting. In this case, set one of the alternative codes to operate this unit separately.

4Press ENTER.

The four-digit code set for the selected component appears in the display window.

Note

“0000” appears in the display window if no code has been set.

5Press the numeric buttons to enter the four-digit remote control code for the component you want to use.

For a complete list of available remote control codes, refer to “LIST OF REMOTE CONTROL CODES” at the end of this manual.

STEREO MUSIC ENTERTAIN MOVIE

1 2 3 4

THX	STANDARD	SELECT EXTD SUR.
5	6	7	8
1	MEMORY 2	A	SPEAKERS B
9	0	+10	ENT.

6Press ENTER to set the number.

“OK” appears in the display window if setting was successful.

“NG” appears in the display window if the setting was unsuccessful. In this case, start over from step 3.

y

If you continuously want to set up another code for another component, press the input selector button or

SELECT k / n to select the component, then repeat steps 4 through 6.

72