Husqvarna 128CD, 128LD manual Basic working techniques, Clearing, Cutting

Page 10

SAFETY INSTRUCTIONS

SCAUTION! Do not use the machine unless you are able to call for help in the event of an accident.

2.Do not use the machine in bad weather, such as dense fog, heavy rain, strong wind, intense cold, etc. Working in bad weather is tiring and often brings added risks, such as icy ground, unpredictable felling direction, etc.

3.Make sure you can move and stand safely. Check the area around you for possible ob- stacles (roots, rocks, branches, ditches, etc.) in case you have to move suddenly. Take great care when working on sloping ground.

4.Switch off the engine before moving to another area.

5.Never put the machine down with the engine running.

Basic working techniques

SAlways slow the engine to idle speed after each working operation. Long periods at

full throttle without any load on the engine can lead to serious engine damage.

SIt is recommended that the engine not be operated for longer than 1 minute at full throttle.

WARNING: Sometimes branches or grass get caught between the guard and cutting attachment. Always stop the engine before cleaning.

Grass trimming using a trimmer head

Trimming

SHold the trimmer head just above the ground at an angle. It is the end of the trim- mer line that does the work. Let the trim- mer line work at its own pace. Never press the trimmer line into the area to be cut.

SThe trimmer line can easily remove grass and weeds up against walls, fences, trees and borders, however it can also damage sensitive bark on trees and bushes, and damage fence posts.

SReduce the risk of damaging plants by shortening the trimmer line to 4--4 1/2 inches

(10--12 cm) and reducing the engine speed.

SWhen trimming you should use less than full throttle so that the trimmer line lasts longer and to reduce the wear on the trimmer head.

Clearing

SThe clearing technique removes all un- wanted vegetation. Keep the trimmer head just above the ground and tilt it. Let the end of the trimmer line strike the ground around trees, posts, statues and the like. IMPORTANT! This technique increases the wear on the trimmer line.

SThe trimmer line wears quicker and must be fed forward more often when working against stones, brick, concrete, metal fences, etc., than when coming into con- tact with trees and wooden fences.

Cutting

SThe trimmer is ideal for cutting grass that is difficult to reach using a normal lawn mower. Keep the trimmer line parallel to the ground when cutting. Avoid pressing the trimmer head against the ground as this can ruin the lawn and damage the tool.

SDo not allow the trimmer head to con-- stantly come into contact with the ground during normal cutting. Constant contact of this type can cause damage and wear to the trimmer head.

115374327 Rev. 6 5/31/12

English--- 10

Page 9 Page 11
Image 10
Page 9 Page 11
Contents Page Contents Symbols KEY to SymbolsRev 5/31/12 Only intended for trimmer heads Stop switch Safety InstructionsMachine’s safety equipment Personal protective equipmentCutting equipment Cutting attachment guardMuffler Trimmer head is intended for trimming grassReturn springs work properly General rules Trimmer headTrimmer line of the same diameter Safety instructions before starting work General safety precautionsSafety instructions regarding the surroundings Personal protectionGeneral working instructions Fuel safetyBasic safety rules StartingClearing Basic working techniquesCutting Sweeping 128LD 128CD Know Your TrimmerKnow your trimmer Assembling and dismantling the two--piece shaft AssemblyFitting the loop handle Fitting the trimmer guard and trimmer head Model 128LDFitting the trimmer guard and trimmer head Model 128CD Fuel mixture Fuel HandlingFueling Starting and stopping Starting and StoppingCheck before starting Cold engineWarm engine StoppingCarburetor MaintenanceUnit/Maintenance Safety MufflerTwo--piece shaft Cleaning the air filterSpark plug Air filterWeekly maintenance Maintenance scheduleDaily maintenance Monthly maintenanceTrimmer Head Line Loading Instructions Technical Data Technical dataWarranty Commencement Date Contrôler les points suivants avant la mise en marche ContenuContenu Avertissement Utilisés deDestiné uniquement aux têtes de coupe Explication DES SymbolesSymboles Un nettoyage régulier est indispensable Examen visuelBlocage de l’accélération Instructions DE SécuritéÉquipement de sécurité de la machine Utiliser des bottes antidéparapantes et stablesAvertissement L’intérieur Avertissement Une exAvertissement Les gaz Instructions DE Sécurité Tête de coupe Règles élémentairesProtection personnelle Avertissement ToujoursInstructions générales de sécurité Consignes de sécurité pour l’entourageSécurité carburant Consignes de sécurité avant la mise en serviceAvertissement Lorsque le Sécurité du mise en marcheTechniques de travail de base Avertissement ManipulerMéthodes de travail Avertissement Il arrive queCoupe Avertissement AttentionBalayage Bouton d’arrêt Huile à 2 temps FAMILIARISEZ-VOUS Avec Votre AppareilFamiliarisez-vous avec votre appareil Manuel d’instructions EPAMontage et démontage d’un tube de transmission démontable MontageMontage de la poignée en boucle Avertissement Tous lesCarburant Manipulation DU CarburantMontage du protecteur et la tête de coupe Modèle 128CD Avertissement Le carbuMélange Avertissement Le potRemplissage de carburant Avertissement Les me Min m 10 ftDémarrage et arrêt Avertissement Un couv Démarrage ET ArrêtContrôles avant la mise en marche Moteur froidMoteur chaud ArrêtEntretien Filtre à air BougieTube de transmission démontable Vis de silencieux Grille pare--étincellesRenvoi d’angle 128LD Schéma d’entretienRemplacement du fil dans la tête de coupe Caractéristiques Techniques Caractéristiques techniquesAccessoires Numéro de la pièce Droits ET Obligations DE Votre GarantieADD-ON or Modified Parts Durée DE Couverture Antes de arrancar, observe lo siguiente ContenidoContenido Advertencia Una desbrozaIdentificacion DE Simbolos SímbolosEquipo de seguridad de la máquina Instrucciones DE SeguridadEquipo de protección personal Advertencia Para trabajar Advertencia Nunca utiliceAdvertencia La sobre ex Advertencia Bajo ningunaAdvertencia Los humos de Interruptor de parada ¡IMPORTANTEObtener un resultado de corte óptimo Advertencia Pare siempreCabezal de corte Reglas básicasProtección personal Instrucciones generales de seguridadAdvertencia Un equipo de Instrucciones de seguridad para el entornoAdvertencia Sea cuidadoso Advertencia Cuando elSeguridad en el uso del com- bustible Seguridad de arranqueAdvertencia a veces, se Instrucciones generales de trabajoTécnica básicas de trabajo Reglas básicas de seguridadCorte BarridoConozca SU Aparato Conozca su aparatoMontaje y desmontaje del tubo divisible MontajeMontaje de mango de tipo cerrado Montaje de la protector y la cabezal de corte Modelo 128LDMontaje de la protector y la cabezal de corte Modelo 128CD Rodeada por el protector de polvoCarburante Manipulacion DEL CombustibleAdvertencia El combus Problemas de funcionamiento RepostajeArranque y parada Advertencia Antes de ar Arranque Y ParadaControl antes de arrancar Motor frioMotor caliente Advertencia Si no puede MantenimientoCarburador Seguridad del aparato y su mantenimientoFiltro de aire BujíaTubo divisible Mm 0,024 de pulgadaEngranaje angulado 128LD Programa de mantenimientoReemplazo de la línea en el cabezal de corte Datos Tecnicos Datos técnicosAccessorios Número de pieza Accesorio del cortadora de ramas, con tubo 952 711Fecha DEL Comienza DE LA Garantia
Related manuals
Manual 4 pages 16.46 Kb Manual 7 pages 30.43 Kb Manual 4 pages 15.86 Kb

128CD, 128LD specifications

The Husqvarna 128LD is a versatile, user-friendly outdoor tool designed to make yard work easier and more efficient. Known for its lightweight design and robust performance, this multi-purpose trimmer is part of Husqvarna's extensive lineup of outdoor power equipment, aimed at both homeowners and professional landscapers.

One of the standout features of the 128LD is its powerful 28cc, 2-stroke engine. This engine provides a perfect blend of performance and fuel efficiency, delivering the power needed to tackle tough grass and weeds while minimizing fuel consumption. The smart design also includes an easy-starting system that reduces the effort required to start the machine, ensuring you can get to work without frustration.

The 128LD is not just a trimmer, but a multi-tool system that accommodates various attachments, such as a blower, edger, and cultivator. This versatility makes it an ideal choice for homeowners looking to maintain their gardens and yards with minimal equipment. The detachable shaft allows for easy swapping of attachments, ensuring that you have the right tool for any task.

Equipped with an adjustable handle, the Husqvarna 128LD promotes comfort and efficiency during use. The soft-grip handle minimizes vibration, allowing you to work longer without discomfort. Additionally, the curved shaft design enhances reach and precision, making it easier to trim around flower beds, pathways, and other narrow spaces.

Another critical feature of the 128LD is its dual line cutting system. This system allows for a wide cutting swath, effectively reducing the time spent on yard work. The patented Tap 'n Go trimmer head enables easy line adjustment, letting you extend the cutting line simply by tapping the head on the ground, ensuring you're always ready to work without interruptions.

In terms of durability, the Husqvarna 128LD is built to last. High-quality materials and construction ensure it can withstand the rigors of outdoor use, providing reliable performance over time.

Overall, the Husqvarna 128LD stands out as a powerful and versatile multitool that caters to a broad range of outdoor maintenance needs, making it a valuable addition to any homeowner's gardening arsenal. Whether you're trimming grass, edging pathways, or tackling tougher overgrown areas, the 128LD delivers reliability and ease of use in one efficient package.
Top Page Image Contents