Husqvarna 128CD Bevel gear 128LD, Maintenance schedule, Daily maintenance, Weekly maintenance

Page 20

MAINTENANCE

Bevel gear (128LD)

The bevel gear is filled with the right quantity of grease at the factory. However, before using the machine you should check

that the bevel gear is filled three--quarters full with grease. Use HUSQVARNA special grease.

The grease in the bevel gear does not nor- mally need to be changed except if repairs are carried out.

Maintenance schedule

Below you will find some general mainte- nance instructions.

Daily maintenance

SCheck throttle trigger and throttle trigger

lockout function.

SCheck that the stop switch works

correctly.

SCheck that there are no fuel leaks from

the engine, tank or fuel lines.

SCheck that the cutter does not rotate when the engine is idling.

SClean the outside of the machine.

SCheck that the harness is not damaged. S Check that the cutting attachment guard

is not damaged or cracked.

S Replace the guard if it is exposed to im- pact or is cracked.

S A non--balanced trimmer head induces heavy vibrations that may damage the machine.

S Check that nuts and screws are tight.

S Check that the screws that hold the bevel gear are tight.

S Check that the trimmer head is tight.

115374327 Rev. 6 5/31/12

Weekly maintenance

SCheck the starter and starter cord. S Clean the carburetor area.

S Clean the outside of the spark plug. Re- move it and check the electrode gap. Ad- just the gap to 0.024″ (0.6 mm), or replace the spark plug. Use resistor spark plug Champion RCJ--6Y or equivalent.

S Clean the cooling fins on the cylinder and check that the air intake near the starter is not blocked.

S Check that the bevel gear is filled with grease up to 3/4 full. Use special grease.

S Clean the air filter.

Monthly maintenance

SClean the fuel tank.

SClean the outside of the carburetor and the space around it.

SClean the fan and the area around it.

SCheck fuel lines for cracks or other dam-

age. Change if necessary.

SChange the fuel filter in fuel tank.

SCheck the clutch, clutch springs and the clutch drum for wear. Replace if neces- sary.

SCheck electrical wires and connections. S Replace the spark plug. Use resistor

spark plug Champion RCJ--6Y or equiva- lent.

S Change the air filter.

English--- 20

Page 19 Page 21
Image 20
Page 19 Page 21
Contents Page Contents Rev 5/31/12 Only intended for trimmer heads KEY to SymbolsSymbols Safety Instructions Machine’s safety equipmentStop switch Personal protective equipmentCutting attachment guard MufflerCutting equipment Trimmer head is intended for trimming grassReturn springs work properly Trimmer line of the same diameter Trimmer headGeneral rules General safety precautions Safety instructions regarding the surroundingsSafety instructions before starting work Personal protectionFuel safety Basic safety rulesGeneral working instructions StartingCutting Basic working techniquesClearing Sweeping Know your trimmer Know Your Trimmer128LD 128CD Assembly Fitting the loop handleAssembling and dismantling the two--piece shaft Fitting the trimmer guard and trimmer head Model 128LDFitting the trimmer guard and trimmer head Model 128CD Fueling Fuel HandlingFuel mixture Starting and Stopping Check before startingStarting and stopping Cold engineWarm engine StoppingMaintenance Unit/Maintenance SafetyCarburetor MufflerCleaning the air filter Spark plugTwo--piece shaft Air filterMaintenance schedule Daily maintenanceWeekly maintenance Monthly maintenanceTrimmer Head Line Loading Instructions Technical Data Technical dataWarranty Commencement Date Contenu ContenuContrôler les points suivants avant la mise en marche Avertissement Utilisés deExplication DES Symboles SymbolesDestiné uniquement aux têtes de coupe Un nettoyage régulier est indispensable Examen visuelInstructions DE Sécurité Équipement de sécurité de la machineBlocage de l’accélération Utiliser des bottes antidéparapantes et stablesAvertissement Les gaz Avertissement Une exAvertissement L’intérieur Instructions DE Sécurité Tête de coupe Règles élémentairesAvertissement Toujours Instructions générales de sécuritéProtection personnelle Consignes de sécurité pour l’entourageConsignes de sécurité avant la mise en service Avertissement Lorsque leSécurité carburant Sécurité du mise en marcheAvertissement Manipuler Méthodes de travailTechniques de travail de base Avertissement Il arrive queBalayage Avertissement AttentionCoupe FAMILIARISEZ-VOUS Avec Votre Appareil Familiarisez-vous avec votre appareilBouton d’arrêt Huile à 2 temps Manuel d’instructions EPAMontage Montage de la poignée en boucleMontage et démontage d’un tube de transmission démontable Avertissement Tous lesManipulation DU Carburant Montage du protecteur et la tête de coupe Modèle 128CDCarburant Avertissement Le carbuAvertissement Le pot Remplissage de carburant Avertissement Les meMélange Min m 10 ftDémarrage ET Arrêt Contrôles avant la mise en marcheDémarrage et arrêt Avertissement Un couv Moteur froidMoteur chaud ArrêtEntretien Bougie Tube de transmission démontableFiltre à air Vis de silencieux Grille pare--étincellesRenvoi d’angle 128LD Schéma d’entretienRemplacement du fil dans la tête de coupe Caractéristiques Techniques Caractéristiques techniquesAccessoires Numéro de la pièce Droits ET Obligations DE Votre GarantieADD-ON or Modified Parts Durée DE Couverture Contenido ContenidoAntes de arrancar, observe lo siguiente Advertencia Una desbrozaIdentificacion DE Simbolos SímbolosInstrucciones DE Seguridad Equipo de protección personal Advertencia Para trabajarEquipo de seguridad de la máquina Advertencia Nunca utiliceAdvertencia Los humos de Advertencia Bajo ningunaAdvertencia La sobre ex Interruptor de parada ¡IMPORTANTEAdvertencia Pare siempre Cabezal de corteObtener un resultado de corte óptimo Reglas básicasInstrucciones generales de seguridad Advertencia Un equipo deProtección personal Instrucciones de seguridad para el entornoAdvertencia Cuando el Seguridad en el uso del com- bustibleAdvertencia Sea cuidadoso Seguridad de arranqueInstrucciones generales de trabajo Técnica básicas de trabajoAdvertencia a veces, se Reglas básicas de seguridadCorte BarridoConozca SU Aparato Conozca su aparatoMontaje Montaje de mango de tipo cerradoMontaje y desmontaje del tubo divisible Montaje de la protector y la cabezal de corte Modelo 128LDMontaje de la protector y la cabezal de corte Modelo 128CD Rodeada por el protector de polvoAdvertencia El combus Manipulacion DEL CombustibleCarburante Problemas de funcionamiento RepostajeArranque Y Parada Control antes de arrancarArranque y parada Advertencia Antes de ar Motor frioMotor caliente Mantenimiento CarburadorAdvertencia Si no puede Seguridad del aparato y su mantenimientoBujía Tubo divisibleFiltro de aire Mm 0,024 de pulgadaEngranaje angulado 128LD Programa de mantenimientoReemplazo de la línea en el cabezal de corte Datos Tecnicos Datos técnicosAccessorios Número de pieza Accesorio del cortadora de ramas, con tubo 952 711Fecha DEL Comienza DE LA Garantia
Related manuals
Manual 4 pages 16.46 Kb Manual 7 pages 30.43 Kb Manual 4 pages 15.86 Kb

128CD, 128LD specifications

The Husqvarna 128LD is a versatile, user-friendly outdoor tool designed to make yard work easier and more efficient. Known for its lightweight design and robust performance, this multi-purpose trimmer is part of Husqvarna's extensive lineup of outdoor power equipment, aimed at both homeowners and professional landscapers.

One of the standout features of the 128LD is its powerful 28cc, 2-stroke engine. This engine provides a perfect blend of performance and fuel efficiency, delivering the power needed to tackle tough grass and weeds while minimizing fuel consumption. The smart design also includes an easy-starting system that reduces the effort required to start the machine, ensuring you can get to work without frustration.

The 128LD is not just a trimmer, but a multi-tool system that accommodates various attachments, such as a blower, edger, and cultivator. This versatility makes it an ideal choice for homeowners looking to maintain their gardens and yards with minimal equipment. The detachable shaft allows for easy swapping of attachments, ensuring that you have the right tool for any task.

Equipped with an adjustable handle, the Husqvarna 128LD promotes comfort and efficiency during use. The soft-grip handle minimizes vibration, allowing you to work longer without discomfort. Additionally, the curved shaft design enhances reach and precision, making it easier to trim around flower beds, pathways, and other narrow spaces.

Another critical feature of the 128LD is its dual line cutting system. This system allows for a wide cutting swath, effectively reducing the time spent on yard work. The patented Tap 'n Go trimmer head enables easy line adjustment, letting you extend the cutting line simply by tapping the head on the ground, ensuring you're always ready to work without interruptions.

In terms of durability, the Husqvarna 128LD is built to last. High-quality materials and construction ensure it can withstand the rigors of outdoor use, providing reliable performance over time.

Overall, the Husqvarna 128LD stands out as a powerful and versatile multitool that caters to a broad range of outdoor maintenance needs, making it a valuable addition to any homeowner's gardening arsenal. Whether you're trimming grass, edging pathways, or tackling tougher overgrown areas, the 128LD delivers reliability and ease of use in one efficient package.
Top Page Image Contents