Husqvarna 128LD, 128CD manual Assembly, Fitting the loop handle

Page 13

ASSEMBLY

NOTE: Make sure unit is assembled cor- rectly as shown in this manual.

Fitting the loop handle

SPosition the handle on the upper shaft. Note that the handle must be mounted between the two arrows on the shaft.

SFit the screw, securing plate and wing

nut as shown in the diagram.

STighten the wing nut.

Assembling and dismantling the two--piece shaft

Assembly:

SLoosen the coupling by turning the knob.

SPosition locking/release button (A) of attachment into guide recess (B) of coupling.

A

B

SPush the attachment into the coupling until the locking/release button snaps into the primary hole (C).

C

SBefore using the unit, tighten the knob securely.

WARNING: All attachments are designed to be used in the primary hole unless otherwise stated in the applicable attachment instruction manual. Using the wrong hole could lead to serious injury or damage to the unit.

115374327 Rev. 6 5/31/12

Dismantling:

SLoosen the coupling by turning the knob.

A

SPress and hold the locking/release but- ton (A).

SWhile securely holding the engine and upper shaft, pull the attachment straight out of the coupling.

Fitting the trimmer guard and trimmer head (Model 128LD)

SFit the correct trimmer guard (D) for use with the trimmer head. Hook the trimmer guard/combination guard onto the fitting on the shaft and secure with the bolt (E).

EF

G

DD

SFit the drive disc (F) on the output shaft. S Turn the shaft until one of the holes in the drive disc aligns with the corresponding

hole in the gear housing.

S Insert hex wrench (G) in the hole to lock the shaft.

S Screw on the trimmer head (H) in the op- posite direction to the direction of rota- tion.

H

STo dismantle, follow the instructions in the reverse order.

English--- 13

Page 12 Page 14
Image 13
Page 12 Page 14
Contents Page Contents Symbols KEY to SymbolsRev 5/31/12 Only intended for trimmer heads Machine’s safety equipment Safety InstructionsStop switch Personal protective equipmentMuffler Cutting attachment guardCutting equipment Trimmer head is intended for trimming grassReturn springs work properly General rules Trimmer headTrimmer line of the same diameter Safety instructions regarding the surroundings General safety precautionsSafety instructions before starting work Personal protectionBasic safety rules Fuel safetyGeneral working instructions StartingClearing Basic working techniquesCutting Sweeping 128LD 128CD Know Your TrimmerKnow your trimmer Fitting the loop handle AssemblyAssembling and dismantling the two--piece shaft Fitting the trimmer guard and trimmer head Model 128LDFitting the trimmer guard and trimmer head Model 128CD Fuel mixture Fuel HandlingFueling Check before starting Starting and StoppingStarting and stopping Cold engineStopping Warm engineUnit/Maintenance Safety MaintenanceCarburetor MufflerSpark plug Cleaning the air filterTwo--piece shaft Air filterDaily maintenance Maintenance scheduleWeekly maintenance Monthly maintenanceTrimmer Head Line Loading Instructions Technical data Technical DataWarranty Commencement Date Contenu ContenuContrôler les points suivants avant la mise en marche Avertissement Utilisés deSymboles Explication DES SymbolesDestiné uniquement aux têtes de coupe Un nettoyage régulier est indispensable Examen visuelÉquipement de sécurité de la machine Instructions DE SécuritéBlocage de l’accélération Utiliser des bottes antidéparapantes et stablesAvertissement L’intérieur Avertissement Une exAvertissement Les gaz Instructions DE Sécurité Règles élémentaires Tête de coupeInstructions générales de sécurité Avertissement ToujoursProtection personnelle Consignes de sécurité pour l’entourageAvertissement Lorsque le Consignes de sécurité avant la mise en serviceSécurité carburant Sécurité du mise en marcheMéthodes de travail Avertissement ManipulerTechniques de travail de base Avertissement Il arrive queCoupe Avertissement AttentionBalayage Familiarisez-vous avec votre appareil FAMILIARISEZ-VOUS Avec Votre AppareilBouton d’arrêt Huile à 2 temps Manuel d’instructions EPAMontage de la poignée en boucle MontageMontage et démontage d’un tube de transmission démontable Avertissement Tous lesMontage du protecteur et la tête de coupe Modèle 128CD Manipulation DU CarburantCarburant Avertissement Le carbuRemplissage de carburant Avertissement Les me Avertissement Le potMélange Min m 10 ftContrôles avant la mise en marche Démarrage ET ArrêtDémarrage et arrêt Avertissement Un couv Moteur froidArrêt Moteur chaudEntretien Tube de transmission démontable BougieFiltre à air Vis de silencieux Grille pare--étincellesSchéma d’entretien Renvoi d’angle 128LDRemplacement du fil dans la tête de coupe Caractéristiques techniques Caractéristiques TechniquesDroits ET Obligations DE Votre Garantie Accessoires Numéro de la pièceADD-ON or Modified Parts Durée DE Couverture Contenido ContenidoAntes de arrancar, observe lo siguiente Advertencia Una desbrozaSímbolos Identificacion DE SimbolosEquipo de protección personal Advertencia Para trabajar Instrucciones DE SeguridadEquipo de seguridad de la máquina Advertencia Nunca utiliceAdvertencia La sobre ex Advertencia Bajo ningunaAdvertencia Los humos de ¡IMPORTANTE Interruptor de paradaCabezal de corte Advertencia Pare siempreObtener un resultado de corte óptimo Reglas básicasAdvertencia Un equipo de Instrucciones generales de seguridadProtección personal Instrucciones de seguridad para el entornoSeguridad en el uso del com- bustible Advertencia Cuando elAdvertencia Sea cuidadoso Seguridad de arranqueTécnica básicas de trabajo Instrucciones generales de trabajoAdvertencia a veces, se Reglas básicas de seguridadBarrido CorteConozca su aparato Conozca SU AparatoMontaje de mango de tipo cerrado MontajeMontaje y desmontaje del tubo divisible Montaje de la protector y la cabezal de corte Modelo 128LDRodeada por el protector de polvo Montaje de la protector y la cabezal de corte Modelo 128CDCarburante Manipulacion DEL CombustibleAdvertencia El combus Repostaje Problemas de funcionamientoControl antes de arrancar Arranque Y ParadaArranque y parada Advertencia Antes de ar Motor frioMotor caliente Carburador MantenimientoAdvertencia Si no puede Seguridad del aparato y su mantenimientoTubo divisible BujíaFiltro de aire Mm 0,024 de pulgadaPrograma de mantenimiento Engranaje angulado 128LDReemplazo de la línea en el cabezal de corte Datos técnicos Datos TecnicosAccesorio del cortadora de ramas, con tubo 952 711 Accessorios Número de piezaFecha DEL Comienza DE LA Garantia
Related manuals
Manual 4 pages 16.46 Kb Manual 7 pages 30.43 Kb Manual 4 pages 15.86 Kb

128CD, 128LD specifications

The Husqvarna 128LD is a versatile, user-friendly outdoor tool designed to make yard work easier and more efficient. Known for its lightweight design and robust performance, this multi-purpose trimmer is part of Husqvarna's extensive lineup of outdoor power equipment, aimed at both homeowners and professional landscapers.

One of the standout features of the 128LD is its powerful 28cc, 2-stroke engine. This engine provides a perfect blend of performance and fuel efficiency, delivering the power needed to tackle tough grass and weeds while minimizing fuel consumption. The smart design also includes an easy-starting system that reduces the effort required to start the machine, ensuring you can get to work without frustration.

The 128LD is not just a trimmer, but a multi-tool system that accommodates various attachments, such as a blower, edger, and cultivator. This versatility makes it an ideal choice for homeowners looking to maintain their gardens and yards with minimal equipment. The detachable shaft allows for easy swapping of attachments, ensuring that you have the right tool for any task.

Equipped with an adjustable handle, the Husqvarna 128LD promotes comfort and efficiency during use. The soft-grip handle minimizes vibration, allowing you to work longer without discomfort. Additionally, the curved shaft design enhances reach and precision, making it easier to trim around flower beds, pathways, and other narrow spaces.

Another critical feature of the 128LD is its dual line cutting system. This system allows for a wide cutting swath, effectively reducing the time spent on yard work. The patented Tap 'n Go trimmer head enables easy line adjustment, letting you extend the cutting line simply by tapping the head on the ground, ensuring you're always ready to work without interruptions.

In terms of durability, the Husqvarna 128LD is built to last. High-quality materials and construction ensure it can withstand the rigors of outdoor use, providing reliable performance over time.

Overall, the Husqvarna 128LD stands out as a powerful and versatile multitool that caters to a broad range of outdoor maintenance needs, making it a valuable addition to any homeowner's gardening arsenal. Whether you're trimming grass, edging pathways, or tackling tougher overgrown areas, the 128LD delivers reliability and ease of use in one efficient package.
Top Page Image Contents