Extron electronic 305SA Connect to the LAN using a CAT 5 cable, Terminal RS-232 Cable color Pin

Page 31

b.Connect the IR/RS-232 projector communication cable as shown for either RS-232 or IR projector control

NOTE: Some projectors require NULL

connection wiring, which inverts the Tx

and Rx connections. See the projector

guide for details.

c.Connect a network cable (CAT 5, 5e, or 6 straight through) from the PVS 305SA IP to the RJ-45 LAN jack on the MLC.

The switcher acts as a 4-port Ethernet switch, when connected to the LAN via the RJ-45 pass-through ports on the rear of the

PVT RGB D IP Plus wallplates .

RS-232 connection

Transmit (Tx)

Receive (Rx) RS-232 to projector Ground ( )

Tx Rx GROUND	IR OUT	Terminal		RS-232 Cable color		Pin
Tx Rx GROUND	IR OUT
DISPLAY			Tx	White		2
RS-232/IR			Tx	White		2
RS-232/IR
MLC 104 IP Plus			Rx	Violet		3
Right Side Panel			Rx	Violet		3
			Ground	Shield		5
	IR connection			Black	IR Emitter
					IR Emitter
		Ground ( )			To projector
		IR Signal			To projector
		IR Signal
Black	Red	Unidirectional IR Output
	Red	via White Striped Wire
		via White Striped Wire
				100'
Tx Rx	GROUND IR OUT			(30.5 m)
Tx Rx	GROUND IR OUT
DISPLAY
RS-232/IR
MLC 104 IP Plus
Right Side Panel
Terminal		IR/RS-232 Cable color			IR Cable color
Ground		Black			Black
IR Signal		Red			White/Black
Connecting RS-232 Cable				Connecting IR Cable
					IR Emitter
				Projector	White
		Projector			White	Black
		Projector			(or striped)
					(or striped)
			MLC IR/RS-232
	9-Pin Female		Comm Cable		Red
					Red	Black
NOTE: Red and black
not used.					NOTE: White, violet, and
					shield not used.
	White
			Shield
	Violet			Black	Red
	Violet
		Tx	Rx GROUND IR OUT	Tx Rx	GROUND IR OUT
			DISPLAY	DISPLAY
			DISPLAY	RS-232/IR
			RS-232/IR	RS-232/IR
			RS-232/IR
			MLC 104 IP Plus

ÁConnect the MLC to the projector with an RS-232 cable or IR emitter cable, as appropriate.

NOTE: Connect to the PVS 305SA IP Ethernet ports as follows:

1.TCP/IP network

2.MLC controller

3.PVT RGB D IP Plus RJ-45 pass-through

4.PVT RGB D IP Plus RJ-45 pass-through

CAT 5, 5e or 6 Cable

TCP/IP	PVS 305SA IP
Network

	LAN	PRESS TAB WITH
	LAN	TWEEKER TO REMOVE
Tx Rx GROUND OUTIR	OUT+12V GROUND CM IRIN SCP	1 2 3	GROUND	Rx	Tx	GROUND	GROUND +12VIN
				A	B
DISPLAY	A B C D E	DIGITAL			MLS		POWER
RS-232/IR	COMM LINK	I/O		RS-232			12V

MLC 104 IP Plus Right Side Panel

ÓConnect to the LAN using a CAT 5 cable.

PoleVault IP Systems • Installation — Stage 2 (Wallplates and MLC)

27

Image 31

Contents PoleVault IP Systems Sicherheitsanweisungen Deutsch Safety InstructionsGuide on the Extron website FCC Class B NoticeVariables are written in slanted form as shown here Specifications AvailabilityConventions Used in this Guide Letter oPoleVault IP System OverviewPoleVault IP System Installation and Wiring Overview Typical Classroom Installation Before You Begin Planning the InstallationLocation of the Screen and Projector Location of MediaLink Controller and Wall Plates Included Items InventorySee rear cover for contact numbers KitsItems Not Included Installation Overview Outline of Installation Steps Stage Installing the Screen Projector Place the PCM 340 on the T-bar Install Projector to Verify LocationMark Screen Location Mark the screen locationScrew the adjuster plate onto the base of the pipe Viii. Evenly balanced configuration Using the slots on the bracket that areClosest to the barrel on each arm, place Verify the Image Location Slide and lock the projector onto the adjuster plateTake the measurements with the PCM 340 on the T-frame Preliminary Safety Hardware InstallationMark the structural ceiling for lag eye bolt installation Cut the Ceiling TileFinish Projector Drop Ceiling Mount Installation Attach the turnbuckles at the corners of the PCM Secure the Projector Drop Ceiling Mount to the CeilingHand tighten all four turnbuckles Install the Screen Install the Electrical Box if requiredShock or serious injury. For safety Install the Raco box and plaster ring onto the PCMPage PVT CV D and PVT RGB D IP Plus AV Source Input Wallplates Cabling for the Wallplates and MediaLink Controller PVT transmitter installationMLC 104 IP Plus installation MLS 104 IP Plus MediaLink ControllerFeatures for MLC Mud Ring Installation Install the Mud RingsInsert the PVT mud ring into the wall Provide strain relief Signal Cable Label colorPull the cables at each location Install Wall Plates Connect the MLC 104 IP Plus to the switcher Install MediaLink ControllerTerminal RS-232 Cable color Pin Connect to the LAN using a CAT 5 cableTCP/IP Connections made to the MLC 104 IP PlusCabling for the Speakers Stage 3 Involves Installing the Devices Shown BelowSpeaker Installation FF 120 Flat Field Ceiling SpeakersCut Ceiling Tile Install the Speaker on the Drop CeilingMark and cut the tile Attach safety cable Stereo output Dual mono output Terminate the Speaker Cable for the PVS SwitcherWire the captive screw connector Stereo or dual mono output using parallel speaker wiringRear View PVS 305SA IP PoleVault SwitcherStage 4 Involves Installing the Devices Shown Below PMK 550 Pole Mount KitInstall the PMK 550 Base Plate Switcher and Projector Cable Overview Pull the Cables at the Switcher locationGather the cables, pass them down the pipe Your completed connections should look like the image below Finish installing the Pole Mount KitConfigure the Switcher MLS Switcher Configuration Program Stage 5 Involves Installing the Programs Shown BelowConfigurator Configure the System GlobalTest the System Check that an image is present, and adjust as neededAdjust the audio levels on the PVS 305SA IP Test the MLC configuration is correctFinal Installation Preset Switch setting Resolution Number Using Preset ModeAny changes to the Edid settings as needed When the image is correct, re-install the wallplateOn the rear panel, set all the DIP switches to off down Using Learn Mode Available on PVT RGB D Plus onlyInstallation Procedure Optional Accessory Installation VoiceLift SystemVoiceLift System Included parts Priority Page Sensor Kit Included Parts Optional Accessory Installation Priority Page Sensor KitTypical paging system with PVS 305SA IP switcher Configuration program for MLSPoleVault Switchers PVS, available at Testing and Adjustment ProcedureExtron Warranty Outline of Installation Steps