Extron electronic 305SA manual Install the PMK 550 Base Plate

Page 38

NOTES:

• The installation must conform to national and local building and electrical codes, and UL requirements. See the device user guide for details.

• The included power supply MUST NOT be installed above the suspended ceiling, in wall cavities or similar locations.

1. — Install the PMK 550 Base Plate

a. Using a 5/32 inch hex wrench, remove the four

cover screws from the center of the PMK 550

and slide the two halves apart. Remove them

from the base plate.

NOTE: If the PoleVault switcher and its power

supply are already installed, go directly to

step 2e.

b. To mount the PoleVault switcher, place the

mounting plate, with the raised tabs upwards,

on top of the switcher top and pass the two

supplied 4-40 x 3/16 inch screws down through

the plate holes and into the top of the switcher

(see image at right). Secure the plate but do

not overtighten.

c. Invert the combined plate and switcher and

hook the plate tabs into the PMK 550 base

plate. Secure it to the base plate with two

screws.

NOTE: The switcher should be mounted

on the same side as the base plate’s

pipe collar. The switcher is secured

inverted to the base plate so that when

the plate is turned over and fastened on

the pole, the device will be in the correct

orientation

Use only the supplied screws to avoid damaging the switcher.

d.Attach the associated power supply with the supplied plastic ties, by passing the ties through the appropriate slots and around the power supply. Tighten until snug.

e.Using a 3/32 inch hex wrench loosen the four pipe collar set screws, and slide the plate up the pipe until the base plate is touching the drop ceiling.

f.Level the plate and secure it in place with the four set screws located on the collar, ensuring that a minimum of three set screws are tightened firmly against the pole.

CONFIG

1

2

INPUT

 

3SELECTION

4

 

 

 

5

 

 

 

 

 

 

AUX

AUDIO

INPUT

 

PVS

 

 

 

 

PEAKAUDIO

MIC

 

 

 

 

 

NORMAL

POLEVAULT

 

 

 

 

 

 

LEVEL

ADJUST

305SA IP

 

 

 

 

SIGNAL

 

 

 

 

 

 

VOICELIFT

PEAK

SWITCHER

 

 

 

 

 

NORMAL

PAGING

 

 

 

 

 

 

SIGNAL

SENSOR

 

Å

Û

 

 

SENSITIVITY

5

 

 

 

AUX AUDIO

 

 

 

 

ÅPlace the plate (with raised tabs up) on the top of the PVS 305SA IP and secure with supplied screws. Û Hook tabs into base plate.

ÛInvert and secure the PVS 305SA IP and Ü the power supply on the PMK 550 base plate.

†Slide the base plate up onto the pole and °secure with the set screws.

34PoleVault IP Systems • Installation — Stage 4 (PMK 550 and PVS 305SA IP)

Page 37 Page 39
Image 38
Page 37 Page 39
Contents PoleVault IP Systems Safety Instructions Sicherheitsanweisungen DeutschFCC Class B Notice Guide on the Extron websiteLetter o Specifications AvailabilityConventions Used in this Guide Variables are written in slanted form as shown hereOverview PoleVault IP SystemPoleVault IP System Installation and Wiring Overview Before You Begin Planning the Installation Typical Classroom InstallationLocation of the Screen and Projector Location of MediaLink Controller and Wall Plates Inventory Included ItemsKits See rear cover for contact numbersItems Not Included Installation Overview Outline of Installation Steps Stage Installing the Screen Projector Mark the screen location Install Projector to Verify LocationMark Screen Location Place the PCM 340 on the T-barScrew the adjuster plate onto the base of the pipe Closest to the barrel on each arm, place Using the slots on the bracket that areViii. Evenly balanced configuration Slide and lock the projector onto the adjuster plate Verify the Image LocationCut the Ceiling Tile Preliminary Safety Hardware InstallationMark the structural ceiling for lag eye bolt installation Take the measurements with the PCM 340 on the T-frameFinish Projector Drop Ceiling Mount Installation Hand tighten all four turnbuckles Secure the Projector Drop Ceiling Mount to the CeilingAttach the turnbuckles at the corners of the PCM Install the Raco box and plaster ring onto the PCM Install the Electrical Box if requiredShock or serious injury. For safety Install the ScreenPage PVT CV D and PVT RGB D IP Plus AV Source Input Wallplates MLS 104 IP Plus MediaLink Controller PVT transmitter installationMLC 104 IP Plus installation Cabling for the Wallplates and MediaLink ControllerInsert the PVT mud ring into the wall Install the Mud RingsFeatures for MLC Mud Ring Installation Pull the cables at each location Signal Cable Label colorProvide strain relief Install Wall Plates Install MediaLink Controller Connect the MLC 104 IP Plus to the switcherConnect to the LAN using a CAT 5 cable Terminal RS-232 Cable color PinConnections made to the MLC 104 IP Plus TCP/IPFF 120 Flat Field Ceiling Speakers Stage 3 Involves Installing the Devices Shown BelowSpeaker Installation Cabling for the SpeakersMark and cut the tile Install the Speaker on the Drop CeilingCut Ceiling Tile Attach safety cable Stereo or dual mono output using parallel speaker wiring Terminate the Speaker Cable for the PVS SwitcherWire the captive screw connector Stereo output Dual mono outputPMK 550 Pole Mount Kit PVS 305SA IP PoleVault SwitcherStage 4 Involves Installing the Devices Shown Below Rear ViewInstall the PMK 550 Base Plate Gather the cables, pass them down the pipe Pull the Cables at the Switcher locationSwitcher and Projector Cable Overview Finish installing the Pole Mount Kit Your completed connections should look like the image belowStage 5 Involves Installing the Programs Shown Below Configure the Switcher MLS Switcher Configuration ProgramConfigure the System Global ConfiguratorCheck that an image is present, and adjust as needed Test the SystemTest the MLC configuration is correct Adjust the audio levels on the PVS 305SA IPFinal Installation When the image is correct, re-install the wallplate Using Preset ModeAny changes to the Edid settings as needed Preset Switch setting Resolution NumberUsing Learn Mode Available on PVT RGB D Plus only On the rear panel, set all the DIP switches to off downVoiceLift System Included parts Optional Accessory Installation VoiceLift SystemInstallation Procedure Optional Accessory Installation Priority Page Sensor Kit Priority Page Sensor Kit Included PartsTesting and Adjustment Procedure Configuration program for MLSPoleVault Switchers PVS, available at Typical paging system with PVS 305SA IP switcherExtron Warranty Outline of Installation Steps
Top Page Image Contents