Extron electronic 305SA manual Stage 5 Involves Installing the Programs Shown Below

Page 41

Stage 5:

Configuring the

PVS 305SA IP Switcher

Stage 5 Involves Installing the Programs Shown Below.

Items needed to help complete this stage:

•Laptop (or PC) with a network connection

•MLS Configuration program (on supplied DVD or by download from www.extron.com)

•Global configurator software

•MLC 104 IP Plus User Guide

•Projector manufacturer guide

•Device driver and driver package (download from www.extron.com)

1.— Configure the Switcher — MLS Switcher Configuration Program

a. Run the DVD (or download) and install on a
PC or laptop the Extron MediaLink Switcher
Configuration program.
b. Ensure the PC and the MLC 104 IP Plus are
connected to the LAN.
NOTE: If this is not possible, connect a
2.5 mm TRS configuration cable (part
number 70-335-01) to the PC and to the
front panel configuration port of the MLC
104 IP Plus.
c. Launch the MLS Configuration utility. Select the
connection format (RS-232 or TCP/IP), or select
the emulation mode (see figure	).
	Û

NOTE: An offline emulation of the

PVS 305SA IP can aid in becoming familiar

with the PVS 305SA IP before configuring

an active unit. For PVS 305SA IP devices,

select the PVS 305SA device in the drop-

down box.

d.Once the program is running click Help, Contents, or press <F1>, and follow the instructions.

The MLS Configuration Utility software

ÛLaunch the MLS Configuration program

ÜSelect “Help, Contents” and follow instructions

PoleVault IP Systems • Installation — Stage 5 (Configuration)

37

Image 41

Contents PoleVault IP Systems Sicherheitsanweisungen Deutsch Safety InstructionsGuide on the Extron website FCC Class B NoticeConventions Used in this Guide Specifications AvailabilityLetter o Variables are written in slanted form as shown herePoleVault IP System OverviewPoleVault IP System Installation and Wiring Overview Typical Classroom Installation Before You Begin Planning the InstallationLocation of the Screen and Projector Location of MediaLink Controller and Wall Plates Included Items InventorySee rear cover for contact numbers KitsItems Not Included Installation Overview Outline of Installation Steps Stage Installing the Screen Projector Mark Screen Location Install Projector to Verify LocationMark the screen location Place the PCM 340 on the T-barScrew the adjuster plate onto the base of the pipe Closest to the barrel on each arm, place Using the slots on the bracket that areViii. Evenly balanced configuration Verify the Image Location Slide and lock the projector onto the adjuster plateMark the structural ceiling for lag eye bolt installation Preliminary Safety Hardware InstallationCut the Ceiling Tile Take the measurements with the PCM 340 on the T-frameFinish Projector Drop Ceiling Mount Installation Hand tighten all four turnbuckles Secure the Projector Drop Ceiling Mount to the CeilingAttach the turnbuckles at the corners of the PCM Shock or serious injury. For safety Install the Electrical Box if requiredInstall the Raco box and plaster ring onto the PCM Install the ScreenPage PVT CV D and PVT RGB D IP Plus AV Source Input Wallplates MLC 104 IP Plus installation PVT transmitter installationMLS 104 IP Plus MediaLink Controller Cabling for the Wallplates and MediaLink ControllerInsert the PVT mud ring into the wall Install the Mud RingsFeatures for MLC Mud Ring Installation Pull the cables at each location Signal Cable Label colorProvide strain relief Install Wall Plates Connect the MLC 104 IP Plus to the switcher Install MediaLink ControllerTerminal RS-232 Cable color Pin Connect to the LAN using a CAT 5 cableTCP/IP Connections made to the MLC 104 IP PlusSpeaker Installation Stage 3 Involves Installing the Devices Shown BelowFF 120 Flat Field Ceiling Speakers Cabling for the SpeakersMark and cut the tile Install the Speaker on the Drop CeilingCut Ceiling Tile Attach safety cable Wire the captive screw connector Terminate the Speaker Cable for the PVS SwitcherStereo or dual mono output using parallel speaker wiring Stereo output Dual mono outputStage 4 Involves Installing the Devices Shown Below PVS 305SA IP PoleVault SwitcherPMK 550 Pole Mount Kit Rear ViewInstall the PMK 550 Base Plate Gather the cables, pass them down the pipe Pull the Cables at the Switcher locationSwitcher and Projector Cable Overview Your completed connections should look like the image below Finish installing the Pole Mount KitConfigure the Switcher MLS Switcher Configuration Program Stage 5 Involves Installing the Programs Shown BelowConfigurator Configure the System GlobalTest the System Check that an image is present, and adjust as neededAdjust the audio levels on the PVS 305SA IP Test the MLC configuration is correctFinal Installation Any changes to the Edid settings as needed Using Preset ModeWhen the image is correct, re-install the wallplate Preset Switch setting Resolution NumberOn the rear panel, set all the DIP switches to off down Using Learn Mode Available on PVT RGB D Plus onlyVoiceLift System Included parts Optional Accessory Installation VoiceLift SystemInstallation Procedure Priority Page Sensor Kit Included Parts Optional Accessory Installation Priority Page Sensor KitPoleVault Switchers PVS, available at Configuration program for MLSTesting and Adjustment Procedure Typical paging system with PVS 305SA IP switcherExtron Warranty Outline of Installation Steps