Extron electronic 305SA manual Location of the Screen and Projector

Page 8

Screen/White Board Location

•Ceiling and wall type (important in assessing the hardware needed)

•

•

Ceiling type: dropped, spline, hard lid and similar. Structural type (wood, concrete, trusses), plenum or non-plenum

Wall type: drywall, cement, brick.

WARNING: Structural ceiling failure could cause death serious injury or

death. Check the structural ceiling to ensure that it can handle a load four times the weight of the final setup.

•Lighting

•Type and control (important for projector image viewing)

•Ambient light from windows

Student Desks

Speaker

Location

Windows

Projector/Switcher

Location

MLC controller

Location

TV / VCR / DVD

Inputs

Teacher’s Desk

PVT A/V Wallplate Location

Figure 3. Example Classroom Installation

b. Location of the Screen and Projector

•

•

•

•

•

•

•

•

•

•

•

•

•

Proposed screen location (normally located at the front center of the room) The lowered screen does not cover safety devices, such as fire alarm strobes. Dimensions and type of screen (maximum image size, motorized or hanging screen) Proposed projector location

Projector aligned with center of the screen and not an obstruction to viewing Projector throw distance (maximum and minimum limits to the screen) of the image

Horizontal offset (horizontal distance from the center of the lens to the center of the projector)

Vertical offset of the projected image (height relationship between the projector and the screen)

Projector angle (image projected up, down, or horizontal to screen)

Power source for the projector: existing and accessible or needing installation

Projector weight: the Universal Projector Bracket (UPB 25) supports a maximum weight of 25 lbs.

Viewing obstructions: Pillars, furniture and so forth, window locations for glare reduction, obstructions between projector and screen.

Overhead clearances (refer to a copy of ADA Standards for Accessible Design, Sections 307 and 308, for ADA requirements)

4PoleVault IP Systems • Introduction

Image 8

Contents PoleVault IP Systems Safety Instructions Sicherheitsanweisungen DeutschFCC Class B Notice Guide on the Extron websiteSpecifications Availability Conventions Used in this GuideLetter o Variables are written in slanted form as shown hereOverview PoleVault IP SystemPoleVault IP System Installation and Wiring Overview Before You Begin Planning the Installation Typical Classroom InstallationLocation of the Screen and Projector Location of MediaLink Controller and Wall Plates Inventory Included ItemsKits See rear cover for contact numbersItems Not Included Installation Overview Outline of Installation Steps Stage Installing the Screen Projector Install Projector to Verify Location Mark Screen LocationMark the screen location Place the PCM 340 on the T-barScrew the adjuster plate onto the base of the pipe Closest to the barrel on each arm, place Using the slots on the bracket that areViii. Evenly balanced configuration Slide and lock the projector onto the adjuster plate Verify the Image LocationPreliminary Safety Hardware Installation Mark the structural ceiling for lag eye bolt installationCut the Ceiling Tile Take the measurements with the PCM 340 on the T-frameFinish Projector Drop Ceiling Mount Installation Hand tighten all four turnbuckles Secure the Projector Drop Ceiling Mount to the CeilingAttach the turnbuckles at the corners of the PCM Install the Electrical Box if required Shock or serious injury. For safetyInstall the Raco box and plaster ring onto the PCM Install the ScreenPage PVT CV D and PVT RGB D IP Plus AV Source Input Wallplates PVT transmitter installation MLC 104 IP Plus installationMLS 104 IP Plus MediaLink Controller Cabling for the Wallplates and MediaLink ControllerInsert the PVT mud ring into the wall Install the Mud RingsFeatures for MLC Mud Ring Installation Pull the cables at each location Signal Cable Label colorProvide strain relief Install Wall Plates Install MediaLink Controller Connect the MLC 104 IP Plus to the switcherConnect to the LAN using a CAT 5 cable Terminal RS-232 Cable color PinConnections made to the MLC 104 IP Plus TCP/IPStage 3 Involves Installing the Devices Shown Below Speaker InstallationFF 120 Flat Field Ceiling Speakers Cabling for the SpeakersMark and cut the tile Install the Speaker on the Drop CeilingCut Ceiling Tile Attach safety cable Terminate the Speaker Cable for the PVS Switcher Wire the captive screw connectorStereo or dual mono output using parallel speaker wiring Stereo output Dual mono outputPVS 305SA IP PoleVault Switcher Stage 4 Involves Installing the Devices Shown BelowPMK 550 Pole Mount Kit Rear ViewInstall the PMK 550 Base Plate Gather the cables, pass them down the pipe Pull the Cables at the Switcher locationSwitcher and Projector Cable Overview Finish installing the Pole Mount Kit Your completed connections should look like the image belowStage 5 Involves Installing the Programs Shown Below Configure the Switcher MLS Switcher Configuration ProgramConfigure the System Global ConfiguratorCheck that an image is present, and adjust as needed Test the SystemTest the MLC configuration is correct Adjust the audio levels on the PVS 305SA IPFinal Installation Using Preset Mode Any changes to the Edid settings as neededWhen the image is correct, re-install the wallplate Preset Switch setting Resolution NumberUsing Learn Mode Available on PVT RGB D Plus only On the rear panel, set all the DIP switches to off downVoiceLift System Included parts Optional Accessory Installation VoiceLift SystemInstallation Procedure Optional Accessory Installation Priority Page Sensor Kit Priority Page Sensor Kit Included PartsConfiguration program for MLS PoleVault Switchers PVS, available atTesting and Adjustment Procedure Typical paging system with PVS 305SA IP switcherExtron Warranty Outline of Installation Steps