Extron electronic 305SA Edid Minder, Using Preset Mode, Preset Switch setting Resolution Number

Page 46

EDID Minder

The PVT RGB D IP Plus (EDID) and the PVT RGB D (EDID) incorporates EDID Minder, which allows the transmitter to communicate the appropriate EDID information to the source, ensuring correct video output resolution.

The 5-pole EDID Minder settings DIP switch is located on the rear of the wallplate. Once installed, these switch settings are only accessible by removing the device from its installed location.

PVT RGB D Plus

AUDIO

IN OUT

COMPUTER IN

MONITOR OUT

S G

IR OUT

The factory EDID setting (default) is 1024x768@60 Hz (preset 2).

The EDID Minder has two modes; a Preset (Emulation) mode and a Learn mode.

•Preset Mode is available on all PVT RGB (EDID) models, and allows selection of pre-programed EDID rates, as shown in the table below.

•Learn Mode is available only on the PVT RGB D Plus model, and enables the displays specific EDID information to be recorded and emulated by the input wallplate.

To use the EDID Minder mode in Preset or Learn Mode, follow the instructions below

Using Preset Mode

1.If already installed, disconnect any sources and displays from the front panel and remove the wallplate from the wall.

EDID

Switch

1	ON
2
3
4	G
5	R
	L
	G S

RGB A RGB B

OUT OUT

	2.	On the rear panel, set DIP switch 1 to 50 or 60 kHz as desired.		ON
	3.	Set DIP switches 2 through 5 accordingly to match the desired EDID rate


		(see the table below).	60		1		2		3		4		5
	4.	Connect the video source to the Computer In VGA connector	Hz					EDID
	4.	Connect the video source to the Computer In VGA connector	50			Selection
		and a local display device to the Monitor Out port.	50			Selection
		and a local display device to the Monitor Out port.	NOTE This setting is for
	5.	Restart the video source and display devices. Verify the image, making	NOTE This setting is for
	5.			1024x768@60 Hz,
		any changes to the EDID settings as needed.		preset 2 (factory default)

6.When the image is correct, re-install the wallplate.

	Preset		Switch setting			Resolution
	Number	2	3	4	5	Resolution
	Number	2	3	4	5

	0	OFF	OFF	OFF	OFF	Learn Mode (PVT RGB D Plus only)

	1	OFF	OFF	OFF	ON	800x600

	2	OFF	OFF	ON	OFF	1024x768 (default)

	3	OFF	OFF	ON	ON	1280x720

	4	OFF	ON	OFF	OFF	1280x768

	5	OFF	ON	OFF	ON	1280x800

	6	OFF	ON	ON	OFF	1280x1024

	7	OFF	ON	ON	ON	1360x768

	8	ON	OFF	OFF	OFF	1366x768

	9	ON	OFF	OFF	ON	1400x1050

	A	ON	OFF	ON	OFF	1440x900

	B	ON	OFF	ON	ON	1600x1200

	C	ON	ON	OFF	OFF	1680x1050

	D	ON	ON	OFF	ON	1920x1080

	E	ON	ON	ON	OFF	1920x1200

	F	ON	ON	ON	ON	N/A

42PoleVault IP Systems • Installation — Stage 5 (Configuration)

Image 46

Contents PoleVault IP Systems Safety Instructions Sicherheitsanweisungen DeutschFCC Class B Notice Guide on the Extron websiteLetter o Specifications AvailabilityConventions Used in this Guide Variables are written in slanted form as shown hereOverview PoleVault IP SystemPoleVault IP System Installation and Wiring Overview Before You Begin Planning the Installation Typical Classroom InstallationLocation of the Screen and Projector Location of MediaLink Controller and Wall Plates Inventory Included ItemsKits See rear cover for contact numbersItems Not Included Installation Overview Outline of Installation Steps Stage Installing the Screen Projector Mark the screen location Install Projector to Verify LocationMark Screen Location Place the PCM 340 on the T-barScrew the adjuster plate onto the base of the pipe Viii. Evenly balanced configuration Using the slots on the bracket that areClosest to the barrel on each arm, place Slide and lock the projector onto the adjuster plate Verify the Image LocationCut the Ceiling Tile Preliminary Safety Hardware InstallationMark the structural ceiling for lag eye bolt installation Take the measurements with the PCM 340 on the T-frameFinish Projector Drop Ceiling Mount Installation Attach the turnbuckles at the corners of the PCM Secure the Projector Drop Ceiling Mount to the CeilingHand tighten all four turnbuckles Install the Raco box and plaster ring onto the PCM Install the Electrical Box if requiredShock or serious injury. For safety Install the ScreenPage PVT CV D and PVT RGB D IP Plus AV Source Input Wallplates MLS 104 IP Plus MediaLink Controller PVT transmitter installationMLC 104 IP Plus installation Cabling for the Wallplates and MediaLink ControllerFeatures for MLC Mud Ring Installation Install the Mud RingsInsert the PVT mud ring into the wall Provide strain relief Signal Cable Label colorPull the cables at each location Install Wall Plates Install MediaLink Controller Connect the MLC 104 IP Plus to the switcherConnect to the LAN using a CAT 5 cable Terminal RS-232 Cable color PinConnections made to the MLC 104 IP Plus TCP/IPFF 120 Flat Field Ceiling Speakers Stage 3 Involves Installing the Devices Shown BelowSpeaker Installation Cabling for the SpeakersCut Ceiling Tile Install the Speaker on the Drop CeilingMark and cut the tile Attach safety cable Stereo or dual mono output using parallel speaker wiring Terminate the Speaker Cable for the PVS SwitcherWire the captive screw connector Stereo output Dual mono outputPMK 550 Pole Mount Kit PVS 305SA IP PoleVault SwitcherStage 4 Involves Installing the Devices Shown Below Rear ViewInstall the PMK 550 Base Plate Switcher and Projector Cable Overview Pull the Cables at the Switcher locationGather the cables, pass them down the pipe Finish installing the Pole Mount Kit Your completed connections should look like the image belowStage 5 Involves Installing the Programs Shown Below Configure the Switcher MLS Switcher Configuration ProgramConfigure the System Global ConfiguratorCheck that an image is present, and adjust as needed Test the SystemTest the MLC configuration is correct Adjust the audio levels on the PVS 305SA IPFinal Installation When the image is correct, re-install the wallplate Using Preset ModeAny changes to the Edid settings as needed Preset Switch setting Resolution NumberUsing Learn Mode Available on PVT RGB D Plus only On the rear panel, set all the DIP switches to off downInstallation Procedure Optional Accessory Installation VoiceLift SystemVoiceLift System Included parts Optional Accessory Installation Priority Page Sensor Kit Priority Page Sensor Kit Included PartsTesting and Adjustment Procedure Configuration program for MLSPoleVault Switchers PVS, available at Typical paging system with PVS 305SA IP switcherExtron Warranty Outline of Installation Steps