Extron electronic manual PMK 550 Pole Mount Kit, PVS 305SA IP PoleVault Switcher, Rear View

Page 37

Stage 4:

Installing the PMK 550

and the PVS 305SA IP

Stage 4 Involves Installing the Devices Shown Below.

PMK 550 Pole Mount Kit

Mounting Plate

Base Plate

To open, remove 4 cover screws (10-32, button head, hex) and slide the covers away.

PMK Covers (2)

•Where it goes: Attaches to slotted pipe, above the projector and close to the drop ceiling.

•What it does: Supports and hides from view the installed PVS 305SA IP switcher, power supply, and any installed optional accessories.

PVS 305SA IP PoleVault Switcher

	PVT RGB D Inputs	VoiceLift	Lineout	Speaker	4-Port 10/100
			Output		Ethernet Switch
	(1-4, A and B)	Receiver Port		Output

				4A RGB
				3A RGB
			2A RGB
			1A RGB
	N15779			4B RGB
		I		/VIDEO
		N		3B RGB
POWER		P		/VIDEO
POWER		T		RGB
		U
		S	2B
			1B RGB
12V	MAX
5A	MAX

RGB

	US
LISTED	VOICELIFT
	RECEIVER

VIDEO

OUTPUTS

OUT LINE

R

LR

L

	AUDIO
AUX	5
INPUT

				OUT
			AUDIO		2/4/8
AMPLIFIED					Ohms
AMPLIFIED
DO NOT				R
GROUND					12V
OR SHORT		L		CONTROLIR
SPEAKER				Rx
OUTPUTS2 WIRING50mA			Tx
CLASS10V			RS-232		MLC/IR
			RS-232
PAGING	VOL/MUTE
SENSOR

4 LAN

3 LAN

2 LAN

1 LAN

N15779

1A1ARGBRGB

2A2ARGB

3A3ARGB

4A4ARGBRGB

17TT

LINE OUT

AMPLIFIED AUDIO OUT

LAN 3

LAN 4

®

US AUDIO/VIDEO

DO NOT

LISTED

APPARATUS

GROUND

OR SHORT

2/4/8

I

OUTPUTS

SPEAKER

Ohms

POWER

N

VIDEO

VOICELIFT

L

R

OUTPUTS

RGB

RECEIVER

CLASS 2 WIRING

L

R

P

U

L

R

10V

50mA

CONTROL

T

Tx Rx IR

12V

S

12V

1B RGB

2B2BRGB

3BRGB

4BRGB

AUX AUDIO

PAGING

RS-232 MLC/IR

/VIDEO3 VIDEO

/VIDEO4 VIDEO

INPUT 5

SENSOR

VOL/MUTE

LAN 1

LAN 2

5A MAX

Power Supply

RGB

Video

Aux Audio

MLC Control

Connector

PVT CV D Inputs

Output

Output

Input

Port

(3 and 4)

Paging Sensor

Volume/Mute

Rear View

Port

Control Port

•Where it goes: PVS 305SA IP and power supply install onto the base plate of the PMK 550.

•What it does: Receives input video and audio signals, and pass through LAN data from AV source input wall plates. Outputs and switches the video and audio signals to projector and ceiling speakers.

PoleVault IP Systems • Installation — Stage 4 (PMK 550 and PVS 305SA IP)

33

Image 37

Contents PoleVault IP Systems Sicherheitsanweisungen Deutsch Safety InstructionsGuide on the Extron website FCC Class B NoticeConventions Used in this Guide Specifications AvailabilityLetter o Variables are written in slanted form as shown herePoleVault IP System OverviewPoleVault IP System Installation and Wiring Overview Typical Classroom Installation Before You Begin Planning the InstallationLocation of the Screen and Projector Location of MediaLink Controller and Wall Plates Included Items InventorySee rear cover for contact numbers KitsItems Not Included Installation Overview Outline of Installation Steps Stage Installing the Screen Projector Mark Screen Location Install Projector to Verify LocationMark the screen location Place the PCM 340 on the T-barScrew the adjuster plate onto the base of the pipe Viii. Evenly balanced configuration Using the slots on the bracket that areClosest to the barrel on each arm, place Verify the Image Location Slide and lock the projector onto the adjuster plateMark the structural ceiling for lag eye bolt installation Preliminary Safety Hardware InstallationCut the Ceiling Tile Take the measurements with the PCM 340 on the T-frameFinish Projector Drop Ceiling Mount Installation Attach the turnbuckles at the corners of the PCM Secure the Projector Drop Ceiling Mount to the CeilingHand tighten all four turnbuckles Shock or serious injury. For safety Install the Electrical Box if requiredInstall the Raco box and plaster ring onto the PCM Install the ScreenPage PVT CV D and PVT RGB D IP Plus AV Source Input Wallplates MLC 104 IP Plus installation PVT transmitter installationMLS 104 IP Plus MediaLink Controller Cabling for the Wallplates and MediaLink ControllerFeatures for MLC Mud Ring Installation Install the Mud RingsInsert the PVT mud ring into the wall Provide strain relief Signal Cable Label colorPull the cables at each location Install Wall Plates Connect the MLC 104 IP Plus to the switcher Install MediaLink ControllerTerminal RS-232 Cable color Pin Connect to the LAN using a CAT 5 cableTCP/IP Connections made to the MLC 104 IP PlusSpeaker Installation Stage 3 Involves Installing the Devices Shown BelowFF 120 Flat Field Ceiling Speakers Cabling for the SpeakersCut Ceiling Tile Install the Speaker on the Drop CeilingMark and cut the tile Attach safety cable Wire the captive screw connector Terminate the Speaker Cable for the PVS SwitcherStereo or dual mono output using parallel speaker wiring Stereo output Dual mono outputStage 4 Involves Installing the Devices Shown Below PVS 305SA IP PoleVault SwitcherPMK 550 Pole Mount Kit Rear ViewInstall the PMK 550 Base Plate Switcher and Projector Cable Overview Pull the Cables at the Switcher locationGather the cables, pass them down the pipe Your completed connections should look like the image below Finish installing the Pole Mount KitConfigure the Switcher MLS Switcher Configuration Program Stage 5 Involves Installing the Programs Shown BelowConfigurator Configure the System GlobalTest the System Check that an image is present, and adjust as neededAdjust the audio levels on the PVS 305SA IP Test the MLC configuration is correctFinal Installation Any changes to the Edid settings as needed Using Preset ModeWhen the image is correct, re-install the wallplate Preset Switch setting Resolution NumberOn the rear panel, set all the DIP switches to off down Using Learn Mode Available on PVT RGB D Plus onlyInstallation Procedure Optional Accessory Installation VoiceLift SystemVoiceLift System Included parts Priority Page Sensor Kit Included Parts Optional Accessory Installation Priority Page Sensor KitPoleVault Switchers PVS, available at Configuration program for MLSTesting and Adjustment Procedure Typical paging system with PVS 305SA IP switcherExtron Warranty Outline of Installation Steps