SMC Networks 5000 manual April 17, 2000 Man ual Versio n

Page 43

the slide adjust screen or when a stored job is recalled and the system is “ON”. Note that the “AUTO ADJUST” key will only appear when the slide adjust switch is ON and the editing cursor is on the slide adjust setpoint of a slide adjust system. An auto adjust sequence always approaches the slide setpoint from above. For instance, if the current position is 10.000 and the slide setpoint is 12.000, the auto adjust sequence might take the slide first to 12.015, then back to 12.004, and then “pulse” the slide the last four thousandths into position. This is to ensure consistent setups by taking up gear lash from the same direction every time. Note that a slide setpoint of 00.000 (used to store a job that will not

overwrite the previous slide setpoint on recall), will prohibit automatic adjustment. Automatic movement is subject to the following conditions:

a)The slide adjust switch must be on.

b)The press must be stopped.

c)The press must be at the top of the stroke.

d)The hydraulic overload on the press, if present, must not be tripped.

e)The Link Master Control (LMC) relay must be engaged.

f)There must be no faults in the slide system and the counterbalance system, if present.

g)The auto adjust sequence for the slide will not start until the counterbalance system, if present, is at least up to its pressure setpoint. If the correct pressure setpoint for the counterbalance has been entered, this will ensure that the counterbalance has taken up any clearances in the slide connection system to increase accuracy of shut height adjustment. When the slide adjust system waits for the counterbalance system to finish adjusting to its pressure setpoint, the status message of the slide adjust system will be “Waiting for Cntr-Bal”.

NOTE! A counterbalance pressure that is far too low or far too high during any shut height adjustment may place excessive load on the shut height adjust motor and may even stall the motor. This condition can also occur with non-automatic motorized slide adjust systems. If the automatic slide adjust doesn’t see slide adjust movement within two seconds of a command to move, it will stop its command to move and generate the Fault message “Slide Did Not Move”.

IMPORTANT! Automatic movement will be terminated if the ESTOP button, “JOG UP” softkey, “JOG DN” softkey, or “CANCEL AUTO ADJUST” softkey is pressed while the slide is moving automatically. Automatic movement will pause if the slide adjust switch is turned off. It will resume when the slide adjust switch is turned back on.

April 17, 2000 Man ual Versio n 1.0

5.5

Page 42 Page 44
Image 43
Page 42 Page 44
Contents OmniLink Table of Contents April 17, 2000 Man ual Versio n Iii April 17, 2000 Man ual Versio n Counterbalance Control Section IntroductionCushion Control Hydraulic Overload Control Shut Height Control1 Numeric Entries Parameter Entry and Access Control2 Text Entry April 17, 2000 Man ual Versio n 1 Key Only Mode Access Control2 Key or Password Mode 6.1 RUN/PROG Key Switch Operation 3 Password Only Mode4 Key and Password Mode 6 Access Control OperationExample Password Entry Sequence 6.2 Password System OperationApril 17, 2000 Man ual Versio n Installation Auto-Setup Module Installation April 17, 2000 Man ual Versio n Valve Systems Type B Valve ConfigurationCounterbalance Control Installation Type C Valve ConfigurationAuto-Counterbalance with Type a Integrated Valve 1 Counterbalance Pressure Transducer Mounting Cushion System Installation 3 Counterbalance System Wiring2 Counterbalance Air Valve System Mounting 1 Cushion Pressure Transducer Mounting 3 Cushion System Wiring2 Cushion Air Valve System Mounting Slide Adjust System Installation Hydraulic Overload System Installation1 Rotary Transducer Mounting 3 Linear Transducer Mounting 2 Rotary Slide Adjust Wiring4 Linear Transducer Slide Adjust Wiring Setting up the OmniLink 5000 for the Auto-Setup Module ConfigurationExample Air Configuration Screen Configuring the Auto-Setup boardAir Pressure HelpAir Slot Hardware DetectedDisplay Weight As Regulator settingMax. Die Weight Min. Die WeightMax. Trip Point Max. Cushion ForceMin. Cushion Force Display Force AsValve Type Fault TimeTolerance Transducer Types2 Configuring Slide Adjust Modules Shutheight Slide SlotShut Height Units Pulse Time Upper LimitLower Limit Pulse DistanceLock Time 2.1 Calibrating Linear Slide Adjust SystemsSerious injury or death Or death 2.2 Calibrating Rotary Slide Adjust SystemsResolver Turns System may fail to calibrateApril 17, 2000 Man ual Versio n April 17, 2000 Man ual Versio n Section Operation April 17, 2000 Man ual Versio n Setpoint Slide Adjust OperationActual Position MAN manual Fault1 Slide On, Manual, and Off Settings StatusApril 17, 2000 Man ual Versio n Pressure Set 4 Slide Fault and StatusDie Weight Set 3 Manual Slide Movement2 Pressure and Force Setpoints 1 Air System On, Manual, and Off SettingsPress Trip Set Actual PressureJob Storage and Recall Issues 3 Air System Fault and StatusApril 17, 2000 Man ual Versio n Main Module Messages Diagnostics Fault and Status MessagesMax. Press. Exceeded Pressure Switch LowUnable to Fill Unable to DumpSlide Adjust Fault Messages Slide Adjust Status Messages Moving Up Auto-AdjustingWaiting S/A Switch Min Position ReachedSection A.1 Example Counterbalance Configuration Section A.2 Example Cushion Configuration Section A.3 Example Hydraulic Overload Configuration April 17, 2000 Man ual Versio n Section A.4 Example Linear Slide Adjust Configuration April 17, 2000 Man ual Versio n Section A.5 Example Rotary Slide Adjust Configuration April 17, 2000 Man ual Versio n April 17, 2000 Man ual Versio n Figure B.1 Typical Counterbalance Wiring Diagram Appendix B Typical Wiring DiagramsFigure B.2 Typical Cushion Wiring Diagram Figure B.3 Conceptual Dual Resolver Mounting Figure B.4 Typical Amci Dual Resolver Wiring Diagram Figure B.5 Typical Gemco Dual Resolver Wiring Diagram Figure B.6 Conceptual Linear Transducer Mounting Figure B.7 Typical Gemco Linear Transducer Wiring April 17, 2000 Man ual Versio n Figure B.11 Typical Slide Air Motor Solenoid Wiring April 17, 2000 Man ual Versio n Figure C.1 Logic Module Firmware Chip Locations Appendix C Installation Of OmniLink 5000 FirmwareApril 17, 2000 Man ual Versio n Power is on Section D.2 Valve Type a Lockout ProcedureMust be done even if a LOX valve is opened in since Section D.4 Valve Type C Lockout Procedure Section D.3 Valve Type B Lockout ProcedureApril 17, 2000 Man ual Versio n April 17, 2000 Man ual Versio n Section E.2 Shut height Calibration Sheets April 17, 2000 Man ual Versio n Section F.3 5000-10C Rotary Shut Height Control Board Section F.2 5000-10B Linear Shut Height Control Board

5000 specifications

SMC Networks 5000 is a robust and versatile networking solution designed to meet the demands of modern digital infrastructures. This device is a part of SMC Networks' extensive product lineup, which caters to both enterprise and small to medium-sized businesses. The SMC 5000 stands out due to its high performance, reliability, and advanced feature set.

One of the key features of the SMC Networks 5000 is its high-speed connectivity. It supports multiple Gigabit Ethernet ports, allowing for fast data transfer and seamless connectivity. This makes it ideal for environments where bandwidth is critical, such as in data centers, large office environments, and educational institutions. The device also includes advanced traffic management capabilities, ensuring efficient data flow and minimizing latency.

Another impressive characteristic of the SMC 5000 is its scalability. As organizations grow and their networking needs evolve, the SMC 5000 can adapt accordingly. It supports a modular design, allowing users to add or remove components based on their specific requirements. This flexibility enables businesses to optimize their network setup without the need for a complete overhaul.

Security is a top priority for SMC Networks, and the 5000 model incorporates advanced security features to protect sensitive data. With built-in firewalls, virtual private network (VPN) support, and robust encryption protocols, the device ensures that unauthorized access is prevented. This is particularly crucial in today’s digital landscape, where cyber threats are increasingly sophisticated.

In terms of management and monitoring, the SMC 5000 offers a user-friendly interface that simplifies network administration. Administrators can easily configure settings, monitor performance metrics, and troubleshoot issues through a centralized dashboard. This streamlines network management tasks and enhances overall efficiency.

The SMC Networks 5000 is also compatible with various networking technologies, including VLAN (Virtual Local Area Network) support, QoS (Quality of Service) features, and IPv6 readiness. These technologies contribute to a more efficient network setup and pave the way for future-proofing as networking standards evolve.

Overall, the SMC Networks 5000 is a reliable and powerful networking solution that provides the performance, security, and scalability necessary for today's demanding network environments. Its combination of advanced features and user-friendly management options makes it an excellent choice for businesses looking to enhance their networking infrastructure. With SMC Networks 5000, organizations can ensure seamless connectivity while effectively managing their growing digital demands.
Top Page Image Contents