SMC Networks 5000 manual Max. Cushion Force, Min. Cushion Force, Display Force As, Max. Trip Point

Page 29

 

are pounds (lbs), kilograms (Kgs), tons, and metric tons (Mtons). Note that the

 

display unit can be changed at any time and is independent of the units that the

 

maximum and minimum die weight are using. If a job was stored in tons, and this

 

unit is changed to pounds, the stored job will still be correct. For example, if 2

 

tons were stored for a job and the display unit is changed to pounds, when the job

 

is recalled it will be set to 4000 pounds.

Max. Cushion Force

This parameter only appears when a cushion is being configured. This should

 

be set to the cushion force generated at its maximum pressure. Note that the units

 

to the right of this parameter are also configurable. When the editing cursor is

 

placed on these units, softkey 1 will read “CHANGE UNIT”. When pressed,

 

pounds, kilograms, tons, or metric tons may be selected from a list. Note that

 

changing the unit here will also change the unit for Min. Cushion Force.

Min. Cushion Force

This parameter only appears when a cushion is being configured. Set this

 

value to the force generated at the Min. Pressure you have selected. Note that the

 

units to the right of this parameter are also configurable. When the editing cursor

 

is placed on these units, softkey 1 will read “CHANGE UNIT”. When pressed,

 

pounds, kilograms, tons, or metric tons may be selected from a list. Note that

 

changing the unit here will also change the unit for Max. Cushion Force.

Display Force As

This parameter only appears when a cushion is being configured. Set this

 

parameter to the units that cushion force should be displayed in. When the

 

“CHANGE UNIT” softkey is pressed, the choices listed will be pounds (lbs),

 

kilograms (Kgs), tons, and metric tons (Mtons). Note that the display unit can be

 

changed at any time and is independent of the units used for minimum and

 

maximum cushion force. If a job was stored in tons, and this unit is changed to

 

pounds, the stored job will still be correct. For example, if 2 tons were stored for

 

a job and the display unit is changed to pounds, when the job is recalled it will be

 

set to 4000 pounds.

Max. Trip Point

This parameter only appears when a hydraulic overload is being configured.

 

This should be set to the trip tonnage at the maximum pressure. Note that the

 

units to the right of this parameter are also configurable. When the editing cursor

 

is placed on these units, softkey 1 will read “CHANGE UNIT”. When pressed,

 

pounds, kilograms, tons, or metric tons may be selected from a list. Note that

 

changing the unit here will also change the unit for Min. Trip Point.

Min. Trip Point

This parameter only appears when a hydraulic overload is being configured.

 

Set this value to the force generated at the Min. Pressure you have selected. Note

 

that the units to the right of this parameter are also configurable. When the

 

editing cursor is placed on these units, softkey 1 will read “CHANGE UNIT”.

 

When pressed, pounds, kilograms, tons, or metric tons may be selected from a list.

 

Note that changing the unit here will also change the unit for Max. Trip Point.

Display Trip As

This parameter only appears when a hydraulic overload is being configured.

 

Set this parameter to the units that the trip point should be displayed in. The

April 17, 2000 Man ual Versio n 1.0

4.5

Page 28 Page 30
Image 29
Page 28 Page 30
Contents OmniLink Table of Contents April 17, 2000 Man ual Versio n Iii April 17, 2000 Man ual Versio n Cushion Control Section IntroductionCounterbalance Control Hydraulic Overload Control Shut Height Control2 Text Entry Parameter Entry and Access Control1 Numeric Entries April 17, 2000 Man ual Versio n 2 Key or Password Mode Access Control1 Key Only Mode 4 Key and Password Mode 3 Password Only Mode6 Access Control Operation 6.1 RUN/PROG Key Switch OperationExample Password Entry Sequence 6.2 Password System OperationApril 17, 2000 Man ual Versio n Installation Auto-Setup Module Installation April 17, 2000 Man ual Versio n Valve Systems Type B Valve ConfigurationCounterbalance Control Installation Type C Valve ConfigurationAuto-Counterbalance with Type a Integrated Valve 1 Counterbalance Pressure Transducer Mounting 2 Counterbalance Air Valve System Mounting 3 Counterbalance System WiringCushion System Installation 2 Cushion Air Valve System Mounting 3 Cushion System Wiring1 Cushion Pressure Transducer Mounting 1 Rotary Transducer Mounting Hydraulic Overload System InstallationSlide Adjust System Installation 3 Linear Transducer Mounting 2 Rotary Slide Adjust Wiring4 Linear Transducer Slide Adjust Wiring Setting up the OmniLink 5000 for the Auto-Setup Module ConfigurationExample Air Configuration Screen Configuring the Auto-Setup boardAir Slot HelpHardware Detected Air PressureMax. Die Weight Regulator settingMin. Die Weight Display Weight AsMin. Cushion Force Max. Cushion ForceDisplay Force As Max. Trip PointTolerance Fault TimeTransducer Types Valve Type2 Configuring Slide Adjust Modules Shut Height Units Slide SlotShutheight Lower Limit Upper LimitPulse Distance Pulse TimeSerious injury or death 2.1 Calibrating Linear Slide Adjust SystemsLock Time Or death 2.2 Calibrating Rotary Slide Adjust SystemsResolver Turns System may fail to calibrateApril 17, 2000 Man ual Versio n April 17, 2000 Man ual Versio n Section Operation April 17, 2000 Man ual Versio n Actual Position Slide Adjust OperationSetpoint 1 Slide On, Manual, and Off Settings FaultStatus MAN manualApril 17, 2000 Man ual Versio n Die Weight Set 4 Slide Fault and Status3 Manual Slide Movement Pressure SetPress Trip Set 1 Air System On, Manual, and Off SettingsActual Pressure 2 Pressure and Force SetpointsJob Storage and Recall Issues 3 Air System Fault and StatusApril 17, 2000 Man ual Versio n Main Module Messages Diagnostics Fault and Status MessagesUnable to Fill Pressure Switch LowUnable to Dump Max. Press. ExceededSlide Adjust Fault Messages Slide Adjust Status Messages Waiting S/A Switch Auto-AdjustingMin Position Reached Moving UpSection A.1 Example Counterbalance Configuration Section A.2 Example Cushion Configuration Section A.3 Example Hydraulic Overload Configuration April 17, 2000 Man ual Versio n Section A.4 Example Linear Slide Adjust Configuration April 17, 2000 Man ual Versio n Section A.5 Example Rotary Slide Adjust Configuration April 17, 2000 Man ual Versio n April 17, 2000 Man ual Versio n Figure B.1 Typical Counterbalance Wiring Diagram Appendix B Typical Wiring DiagramsFigure B.2 Typical Cushion Wiring Diagram Figure B.3 Conceptual Dual Resolver Mounting Figure B.4 Typical Amci Dual Resolver Wiring Diagram Figure B.5 Typical Gemco Dual Resolver Wiring Diagram Figure B.6 Conceptual Linear Transducer Mounting Figure B.7 Typical Gemco Linear Transducer Wiring April 17, 2000 Man ual Versio n Figure B.11 Typical Slide Air Motor Solenoid Wiring April 17, 2000 Man ual Versio n Figure C.1 Logic Module Firmware Chip Locations Appendix C Installation Of OmniLink 5000 FirmwareApril 17, 2000 Man ual Versio n Must be done even if a LOX valve is opened in since Section D.2 Valve Type a Lockout ProcedurePower is on Section D.4 Valve Type C Lockout Procedure Section D.3 Valve Type B Lockout ProcedureApril 17, 2000 Man ual Versio n April 17, 2000 Man ual Versio n Section E.2 Shut height Calibration Sheets April 17, 2000 Man ual Versio n Section F.3 5000-10C Rotary Shut Height Control Board Section F.2 5000-10B Linear Shut Height Control Board

5000 specifications

SMC Networks 5000 is a robust and versatile networking solution designed to meet the demands of modern digital infrastructures. This device is a part of SMC Networks' extensive product lineup, which caters to both enterprise and small to medium-sized businesses. The SMC 5000 stands out due to its high performance, reliability, and advanced feature set.

One of the key features of the SMC Networks 5000 is its high-speed connectivity. It supports multiple Gigabit Ethernet ports, allowing for fast data transfer and seamless connectivity. This makes it ideal for environments where bandwidth is critical, such as in data centers, large office environments, and educational institutions. The device also includes advanced traffic management capabilities, ensuring efficient data flow and minimizing latency.

Another impressive characteristic of the SMC 5000 is its scalability. As organizations grow and their networking needs evolve, the SMC 5000 can adapt accordingly. It supports a modular design, allowing users to add or remove components based on their specific requirements. This flexibility enables businesses to optimize their network setup without the need for a complete overhaul.

Security is a top priority for SMC Networks, and the 5000 model incorporates advanced security features to protect sensitive data. With built-in firewalls, virtual private network (VPN) support, and robust encryption protocols, the device ensures that unauthorized access is prevented. This is particularly crucial in today’s digital landscape, where cyber threats are increasingly sophisticated.

In terms of management and monitoring, the SMC 5000 offers a user-friendly interface that simplifies network administration. Administrators can easily configure settings, monitor performance metrics, and troubleshoot issues through a centralized dashboard. This streamlines network management tasks and enhances overall efficiency.

The SMC Networks 5000 is also compatible with various networking technologies, including VLAN (Virtual Local Area Network) support, QoS (Quality of Service) features, and IPv6 readiness. These technologies contribute to a more efficient network setup and pave the way for future-proofing as networking standards evolve.

Overall, the SMC Networks 5000 is a reliable and powerful networking solution that provides the performance, security, and scalability necessary for today's demanding network environments. Its combination of advanced features and user-friendly management options makes it an excellent choice for businesses looking to enhance their networking infrastructure. With SMC Networks 5000, organizations can ensure seamless connectivity while effectively managing their growing digital demands.
Top Page Image Contents