Panasonic WV-CU360C manual Camera Patrol Learning, Program

Page 36

7.Move the cursor to [SPECIAL] on the Setup menu, and press numeric buttons 4 and 6 simultaneously for 2 seconds or more to display the special menu.

8.Move the cursor to [CAMERA RESET]* on the Setup menu, and press buttons 4, 5 and 6 simultaneously to reset all the functions to the defaults.

*The menu to reset the camera functions differs depend- ing on the camera:

[SPECIAL] for the WV-CS650, [SPECIAL 2] for the WV- CS854, and [END] for fixed cameras etc.

Notes:

If camera setup is started using the buttons on the camera, all future operations for setup must be per- formed using the buttons on the camera.

If camera setup is started using the System Controller, all future operations for setup must be performed using the same controller.

For further information, refer to the Operating Instructions for the selected camera.

Keys used for camera setup

Camera Patrol Learning

There are two ways of setting up camera patrol learning. One is to use the camera setup menu and the other is to operate the camera.

Follow the procedures below to set up while operating the combination camera.

1.Select the desired system unit, monitor and combina- tion camera.

2.Press the PATROL PLAY/PATROL LEARN button while holding down the PROGRAM/CAM SETUP/CAM FUNCTION button.

PROGRAM

PATROL PLAY

CAM SETUP

PATROL

LEARN

CAM FUNCTION

[LEARNING] appears on the monitor.

2

 

8

 

 

 

 

 

 

4

 

6

 

 

 

CAM

SET

MON

ESC

To move the cursor

To select a parameter

To execute the mode or enter a submenu

To return to the previous menu

LEARNING

3.Operate the camera using the following controls so that it traces a routine course most frequently patrolled. The learning is programmed for 30 seconds for later patrol play.

Pan/Tilt (Joystick)

Iris (Open/Close)

Focus (Far/Near)

Zoom (Tele/Wide)

Preset Position

Note: The memorized parameters may differ somewhat depending on the camera type. Refer to the manual included with the camera.

4.To stop the learning, press the SEQUENCE/PATROL STOP button while holding down the PROGRAM/CAM SETUP/CAM FUNCTION button.

PROGRAMSEQUENCE

CAM SETUP

 

 

 

 

PATROL

 

 

 

 

CAM FUNCTION

STOP

 

[LEARNING] disappears from the monitor.

36

Image 36
Contents Operating Instructions 360CEnglish Version Important Safety Instructions Contents Handle the appliance with care Do not use any AC adapter other than the one suppliedController Number Switch Controller No Mode Selection Switches ModeData Ports Data DC 9 V Input Jack DC 9VInstallations Template MountingRear Panel Switch Setting Summary WJ-FS616CPanasonic Security Data PSData Systems Operate indicator Operate Login indicator LoginAlarm indicator Alarm Busy indicator Busy Monitor/Unit indicator MONITOR/ Unit4Home/Preset/Programme Preset button 8Programme/Camera Setup/Camera Function button9Setup/Function button SETUP/FUNCTION Iris buttons IRIS, CLOSE/OPEN@5Alarm Suspend button ALM Suspend @6Alarm Reset/Alarm Recall button ALM RESET/ALM@2Defroster/Auxiliary 2 button DEF/AUX @3Wiper/Auxiliary 1 button WIPER/AUXInstallations PSData System ConnectionsConnection Example Internal Diagram Data Port Connection PS DataBasic Connection DIP Switch Setting PS Data Daisy Chain ConnectionController Number Setting PS Data Mode Switch Setting for System ExampleController Setup Procedures PSData Prior to SetupButtons and Controls used for Setup Setup Menus Administrator Authorization Baud RateParity Wait TimeUser Password Administrator PasswordUser Password Certification Unit a button AssignmentCamera Cleaning Unit Connection TestAvailable camera numbers Operating Procedures PSData Basic Operating FlowLogin/Logout LogLog Out System Unit Selection Selecting with Unit NumberSelecting with Unit A/UNIT B Button Monitor Selection Camera SelectionHome/Preset Position Camera ControlPan/Tilt Control Lens ControlCombination Camera Shortcuts IrisHousing/AUX Control SettingData Multiplex Unit Control Camera SelectionVideo Multiplexer Control Multiscreen SelectionStill Picture Electronic ZoomViewing Playback Sequence ControlDigital Disk Recorder Control WJ-HD100 ShortcutsWJ-HD500A Shortcuts Show/Hide Alarm Log Alarm Log 1 line UpAlarm Log 1 line Down Playback of Selected Alarm Alarm LogAlarm Operation Alarm ResetAlarm Recall Press the ALM RESET/ALM Recall buttonRemote Setup of Units & Cameras Camera SetupSystem Unit Setup Camera Patrol Learning ProgramCamera Preset Position For WJ-FS616C Multiplexer System Front View Template for WJ-FS616C 8Alarm Reset button ALM Reset @1Alarm Suspend button ALM Suspend0Home/Decrement button Home 1Auto Focus button Auto Focus@5Preset Position button PRE Posi @8Set Up button SET UP ON/OFF@6Still button Still @7Camera Set buttons Camera SET ON/OFFInstallations For WJ-FS616/FS616C WJ-FS616CDIP Switch Setting For Multiplexer Data Port Connection For MultiplexerController Number Setting Switch Setting ProceduresUnit Version WJ-FS616Setup Procedures For WJ-FS616/FS616C Controller Setup COM Port Setup Operating Procedures For WJ-FS616/FS616C System AUX ControlAlarm Suspension VTR VCR ControlGeneral Setup Shortcut for Preset Position SetupFor WJ-SX350 Matrix Switcher System Log-in indicator Login Front View Template for WJ-SX350LED Display Monitor Camera 3Preset Position button Preset POSI/CAM Posi @0Alarm Acknowledgment and Reset button ACK/RESETIris buttons Iris CLOSE/OPEN Focus buttons Focus NEAR/FAR@3All Alarms Reset button ALL Reset @6Alarm Recall button Recall#1Set Up button SET UP @1@2Backward/Forward Sequence button SEQ BACK/FWDInstallations For WJ-SX350 Example below shows a typical system connectionDIP Switch Setting For WJ-SX350 Data Port Connection For WJ-SX350For version 6.00 or later, set the switches as shown below Controller Setup Procedures For WJ-SX350 Setup Procedures Operating Procedures For WJ-SX350 Login & LogoutLens Control Auto Focus Operation Pan/Tilt Control Camera Position OperationCamera Housing Control Pan/Tilt Control Auto/Random PanningAuxiliary Control Wiper controlSystem Status Display For System WJ-SX850 Matrix Switcher System Front View Template for System 850 Matrix Switcher Link indicator Link Camera indicator CameraAlarm indicator Alarm Monitor indicator Monitor3Programme Preset button Program Preset 4Call Preset button Call Preset9Alarm button ALARM, Disarm indicator Disarm @0Alarm Acknowledge button ACK@1Alarm Reset button Reset @2Group Preset button Group Preset@3Previous button Prev @4Next button NextPage Installations For System Sensors System Matrix SwitcherData Port Connection TX B TX a RX B RX aDIP Switch Setting Setup Procedures For System Setup Procedures Operating Procedures For System Turn on the power switches of all system componentsAppendix Specifications ControllerALL Reset Panasonic Canada Inc