Panasonic WV-CU360C @1@2Backward/Forward Sequence button SEQ BACK/FWD, @9Status button Status

Page 54

@1@2Backward/Forward Sequence button (SEQ BACK/FWD)

BACK: In combination with the numeric buttons, runs a Tour or Group sequence backward on the selected monitor.

It is also used to continue a sequence backward, that was previously paused on that monitor by pressing the PAUSE button.

FWD: In combination with the numeric buttons, runs a Tour or Group sequence forward on the selected monitor.

It is also used to continue a sequence forward, that was previously paused on that monitor by pressing the PAUSE button.

@3All Alarms Reset button (ALL RESET)

Cancels all active alarms at a time.

To reset all alarms, first select the alarmed monitor (Monitor 1 for Alarm Mode 1, any of four monitors for Alarm Mode 2), and then press this button.

Note: To cancel all alarms without first selecting the monitor, press this button in combination with the ALT button.

@4@5Decrement/Increment button (–1CAM DEC, +1CAM INC)

–1CAM DEC: Moves a sequence one step backward from the step that was previously paused on the selected monitor by pressing the PAUSE button.

Also, when the selected monitor is in the spot mode, pressing this button will replace the currently selected camera with the next lower number cam- era.

+1CAM INC: Moves a sequence one step forward from the step that was previously paused on a monitor by pressing the PAUSE button.

Also, when the selected monitor is in the spot mode, pressing this button will replace the currently selected camera with the next higher number cam- era.

@6Alarm Recall button (RECALL)

Recalls the Alarm Log (record of activated alarms). Select the desired monitor to display the alarm records, then press this button to toggle the display of alarm records On and Off on the selected monitor.

@7@8Backward/Forward History button

(HISTORY BACK/FWD)

BACK: Displays the previous camera picture on the selected monitor. Each operation of this button backs up the camera picture by one.

In the SETUP MENU, selects the previous page or step of the setup tables.

FWD: Moves the camera picture forward on the select- ed monitor after the HISTORY BACK button has been used.

In the SETUP MENU, selects the next page or step of the setup tables.

@9Status button (STATUS)

Toggles the display of the Camera Site Status Table on the selected monitor On and Off.

Note: To toggle the display of the System Status Table on the selected monitor On and Off, press this but- ton in combination with the ALT button.

#0Camera Menu button (CAM MENU)

In combination with the ALT button, toggles the display of the selected Camera’s Setup Menu On and Off.

The indicator lights up when the camera setup mode is selected.

#1Set Up button (SET UP)

In combination with the ALT button, toggles the display of the SETUP MENU of the Matrix Switcher On and Off. The indicator lights up when the setup mode is select- ed.

56

Page 53 Page 55
Image 54
Page 53 Page 55
Contents Operating Instructions 360CEnglish Version Important Safety Instructions Contents Handle the appliance with care Do not use any AC adapter other than the one suppliedData Ports Data Controller Number Switch Controller NoMode Selection Switches Mode DC 9 V Input Jack DC 9VInstallations Template MountingRear Panel Switch Setting Summary WJ-FS616CPanasonic Security Data PSData Systems Alarm indicator Alarm Busy indicator Busy Operate indicator OperateLogin indicator Login Monitor/Unit indicator MONITOR/ Unit9Setup/Function button SETUP/FUNCTION 4Home/Preset/Programme Preset button8Programme/Camera Setup/Camera Function button Iris buttons IRIS, CLOSE/OPEN@2Defroster/Auxiliary 2 button DEF/AUX @5Alarm Suspend button ALM Suspend@6Alarm Reset/Alarm Recall button ALM RESET/ALM @3Wiper/Auxiliary 1 button WIPER/AUXInstallations PSData System ConnectionsConnection Example Internal Diagram Data Port Connection PS DataBasic Connection DIP Switch Setting PS Data Daisy Chain ConnectionController Number Setting PS Data Mode Switch Setting for System ExampleController Setup Procedures PSData Prior to SetupButtons and Controls used for Setup Setup Menus Parity Administrator AuthorizationBaud Rate Wait TimeUser Password Certification User PasswordAdministrator Password Unit a button AssignmentCamera Cleaning Unit Connection TestAvailable camera numbers Operating Procedures PSData Basic Operating FlowLogin/Logout LogLog Out System Unit Selection Selecting with Unit NumberSelecting with Unit A/UNIT B Button Monitor Selection Camera SelectionPan/Tilt Control Home/Preset PositionCamera Control Lens ControlCombination Camera Shortcuts IrisData Multiplex Unit Control Housing/AUX ControlSetting Camera SelectionStill Picture Video Multiplexer ControlMultiscreen Selection Electronic ZoomViewing Playback Sequence ControlDigital Disk Recorder Control WJ-HD100 ShortcutsWJ-HD500A Shortcuts Alarm Log 1 line Down Playback of Selected Alarm Show/Hide Alarm LogAlarm Log 1 line Up Alarm LogAlarm Recall Alarm OperationAlarm Reset Press the ALM RESET/ALM Recall buttonRemote Setup of Units & Cameras Camera SetupSystem Unit Setup Camera Patrol Learning ProgramCamera Preset Position For WJ-FS616C Multiplexer System Front View Template for WJ-FS616C 0Home/Decrement button Home 8Alarm Reset button ALM Reset@1Alarm Suspend button ALM Suspend 1Auto Focus button Auto Focus@6Still button Still @5Preset Position button PRE Posi@8Set Up button SET UP ON/OFF @7Camera Set buttons Camera SET ON/OFFInstallations For WJ-FS616/FS616C WJ-FS616CDIP Switch Setting For Multiplexer Data Port Connection For MultiplexerUnit Version Controller Number SettingSwitch Setting Procedures WJ-FS616Setup Procedures For WJ-FS616/FS616C Controller Setup COM Port Setup Operating Procedures For WJ-FS616/FS616C System AUX ControlAlarm Suspension VTR VCR ControlGeneral Setup Shortcut for Preset Position SetupFor WJ-SX350 Matrix Switcher System Log-in indicator Login Front View Template for WJ-SX350LED Display Monitor Camera Iris buttons Iris CLOSE/OPEN 3Preset Position button Preset POSI/CAM Posi@0Alarm Acknowledgment and Reset button ACK/RESET Focus buttons Focus NEAR/FAR#1Set Up button SET UP @3All Alarms Reset button ALL Reset@6Alarm Recall button Recall @1@2Backward/Forward Sequence button SEQ BACK/FWDInstallations For WJ-SX350 Example below shows a typical system connectionDIP Switch Setting For WJ-SX350 Data Port Connection For WJ-SX350For version 6.00 or later, set the switches as shown below Controller Setup Procedures For WJ-SX350 Setup Procedures Lens Control Auto Focus Operation Operating Procedures For WJ-SX350Login & Logout Pan/Tilt Control Camera Position OperationAuxiliary Control Camera Housing ControlPan/Tilt Control Auto/Random Panning Wiper controlSystem Status Display For System WJ-SX850 Matrix Switcher System Alarm indicator Alarm Front View Template for System 850 Matrix SwitcherLink indicator Link Camera indicator Camera Monitor indicator Monitor9Alarm button ALARM, Disarm indicator Disarm 3Programme Preset button Program Preset4Call Preset button Call Preset @0Alarm Acknowledge button ACK@3Previous button Prev @1Alarm Reset button Reset@2Group Preset button Group Preset @4Next button NextPage Installations For System Sensors System Matrix SwitcherData Port Connection TX B TX a RX B RX aDIP Switch Setting Setup Procedures For System Setup Procedures Operating Procedures For System Turn on the power switches of all system componentsAppendix Specifications ControllerALL Reset Panasonic Canada Inc
Top Page Image Contents