Sigma EF-500 manual Description of the Parts, About the Battery, Battery Loading

Page 16

DESCRIPTION OF THE PARTS

EXTERNAL PARTS

1.Flash Head 2.Built-in Wide Panel

3.AF Auxiliary Light 4.Bounce Angle; Up and Down 5.Bounce

Angle; Right and Left

6.Bounce Lock and Release Button; Up and Down

7.Swivel Lock and Release

Button; Right and Left

8.LCD Panel

9.Battery Cover 10.Shoe Ring 11.Shoe

CONTROLS

 

 

 

 

12.MODE Button

13.<SEL> SELECT Button 14.< + > Increment Button

15.< - > Decrement Button

16.ZOOM Button

17.TEST Button 18.LIGHT Button 19.Ready Light 20.Power Switch

ABOUT THE BATTERY

This flash unit uses four “AA” type Alkaline dry cell batteries or Ni-Cad, Ni-MH, rechargeable batteries. Manganese batteries can also be used but as they have a shorter life than Alkaline batteries, we do not recommend using them. Please replace batteries if it takes more than 30seconds to light the Ready Lamp.

To assure proper electrical contact, clean the battery terminals before installing the batteries

NiCad batteries do not have standardized contacts. If you use NiCad batteries, please confirm that the battery contacts touch the battery compartment properly.

To prevent battery explosion, leakage or overheating, use four new AA batteries of the same type and brand. Do not mix the type or new and used batteries.

Do not disassemble or short-circuit batteries, or expose them fire or water; they may explode. Also, do not recharge the batteries other than Ni-Cd rechargeable batteries.

When the flash will not be used for an extended period of time, remove the batteries from the flash, to avoid the possibility of damage from leakage.

Battery performance decreases at low temperatures. Keep batteries insulated when using the flash in cold weather.

As with any flash, it is recommended you carry spare batteries when on a long trip, or when photographing outdoors in cold weather.

BATTERY LOADING

1.Be sure to set the Power Switch to the off position then slide, the battery cover in the direction of the arrow to open.

2.Insert four AA size batteries into the battery chamber. Be sure the + and – ends of the batteries are aligned according to the diagram in the chamber.

3.Close the cover.

4.Slide the Power Switch to the ON position. After few

seconds, the Ready Lamp will light, indicating that the flash unit can be fired.

5.Please press the “Test Button” to be sure that the flash is working properly.

AUTO POWER OFF

To conserve battery power, the flash unit automatically turns itself off when the flash is not used within approximately 5 minutes. To turn the flash on again, depress the TEST button or the camera shutter button, halfway. Please note that, “Auto Power Off” mechanism does not work with wireless TTL flash mode, normal slave flash, and designated slave flash modes.

ERROR INDICATION

If the battery power is not sufficient or there is electric information error between the camera and flash unit, the “Er” mark will blink on the LCD panel. When this occurs, turn the power switch off and on. If it still blinks, after this procedure, check the battery power.

ADJUSTING THE FLASH HEAD

Depress the Bounce “Up and Down” Lock and Release Button, and adjust the flash head to the desired position.

appears on the LCD panel, when you turn on the flash, and if this mark blinks, then the flash head is adjusted to an incorrect position.

16

Image 16
Contents EF-500DG Super 12 13 14 15 EF-500 DG Super SA-N 䟺1䝞䞀䜼䟻 䜿䝇䝌 䜯䝥䝭 䝳䜨䝍 䝑䝯䛱䛪䛊䛬 TTLPage 䝢䝏䝩䜦䝯 䜻䝷䜳䝱 䝦䝋䝮䝷䜴 䜪䝷䜽 䜽䝰䞀䝚 SEL SD9 SD10 EF-500 DG Super SA-N TTL ッ䛮䜦䝙䝃䞀 䞀䝗䜽䛱䛪䛊䛬 Precautions About the Battery Battery LoadingAdjusting the Flash Head Description of the PartsSetting of Flash Coverage Angle Attaching and Removing the Flash to and from the CameraWide Panel Case of use with Sigma SD9 SD10Or a service station Shutter Speed Priority Setting Aperture Priority SettingWhen used with M Mode LCD Panel IlluminationLimits of Continuous Shooting Manual Flash OperationSecond Curtain Synchronization RED-EYE ReductionModeling Flash Exposure CompensationMulti Flash Mode Wireless Flash Except SD9Bounce Flash Close-up ExposuresWhen Built-in Flash is Used SA-7 and SA-9 Control System ChangeNormal Slave Flash Slave FlashDesignated Slave Flash Specifications Vorsichtsmaßnahmen DeutschBeschreibung der Teile BatteriehinweiseEinlegen der Batterien Einstellen des BlitzkopfesEinstellen des Ausleuchtwinkels Zoomreflektor Anbringen und Abnehmen des BlitzgerätesWeitwinkelstreuscheibe Autorisierten Sigma Service Beleuchtung DER LCD TTL BlitzautomatikManueller Blitzbetrieb Grenzen der SerienauslösungKurzzeitblitzsynchronisation FP außer SA-300 Synchronisation auf den zweiten Verschlussvorhang Reduzierung roter AugenEinstelllicht BelichtungskorrekturIndirektes Blitzen StroboskopbetriebKabelloses Blitzen Ausser SD9 Unter Einsatz des eingebauten Blitzgerätes 䟺SA-7 und SA-9䟻 Wechsel der SystemsteuerungEinsatz an Kameras ohne eingebauten Blitz SD10 Normaler „Slave Geräte Betrieb „Slave GerätKabellose Zündung bestimmter „Slave Geräte Technische Daten Français Alimentation Electrique Description DES ElementsMise EN Place DES Piles Ajustement DE LA Tete Flash Mise EN Place ET Retrait DU FlashReglage DE Langle DE Couverture Elargisseur DangleMode de priorité à la vitesse Mode de priorité à louvertureMode manuel M Retro Eclairage DE Lecran LCDLimites DES Prises DE VUE Consecutives AU Flash Mode Operatoire EN Flash ManuelFlash Haute Vitesse FP sauf SA-300 Synchronisation SUR LE Deuxieme Rideau Reduction DE Leffet Yeux RougesFlash Predictif Correction DexpositionMode DE Flash Stroboscopique Multi Flash Flash IndirectFlash Sans Cordon Sauf SD9 Prise de vue rapprochéeUtilisation avec le flash intégré SA-7 et SA-9䟻 Initialisation du système de contrôleUtilisation dun boîtier dépourvu de flash intégré SD10 Flash esclave Normal Flash esclaveFlash esclave désigné Caracteristiques Techniques Préparation du flash de contrôlePrecauciones Advertencia CuidadoAcerca DE LAS Pilas Descripción DE LAS PartesCarga DE LAS Pilas Montar Y Desmontar EL Flash a LA Camara Ajuste DEL Cabezal DEL FlashAjustar EL Angulo DE Cobertura DEL Flash Pantalla Angular Iluminación DE LA Pantalla LCDFlash Automático TTL Ajuste para la prioridad de velocidadLimitaciones DEL Disparo Continuo Operación CON EL Flash ManualAjuste para prioridad de diafragma Cuando se utiliza con el Modo MReduccion DE Ojos Rojos Sincronización CON LA Segunda CortinillaLUZ DE Modelado Compensación DE Exposición Modo DE Multi Flash EstroboscópicoFlash Reflejado Exposiciones de AproximaciónSistema de Control de Cambios Control Remoto DEL Flash Excepto SD9Al emplear el flash de la propia cámara SA-7 y SA-9䟻 Las cámaras que no lleven flash incorporado SD10Flash esclavo Normal Flash esclavoDesignación del flash esclavo Especificaciones Para que la cantidad de salida parpadeeAttenzione Descrizione Delle PartiBatteria Caricamento Delle BatterieRegolazione Della Testa DEL Flash Collegare E Separare IL Flash Dalla MacchinaPannello Wide Regolazione Dellangolo DI Copertura DEL FlashIlluminazione DEL Display LCD Flash Automatico TTL Limitazioni Quando SI Scatta in SequenzaFP Flash Flash AD Alta Velocità Eccetto SA-300 Flash ManualeSincronizzazione Della Seconda Tendina Compensazione DELL’ESPOSIZIONE Flash DI RiempimentoModalità Multi Flash Flash Indiretto Cambiamento del Sistema di ControlloUso del flash incorporato della䟺SA-7 e SA-9䟻 Uso con le fotocamere non dotate di flash incorporato SD10Flash ausiliario normale Flash ausiliarioScegliere i flash secondari Specifiche Bemærk Beskrivelse AF Flashens DeleVedr Batterier Isætning AF BatterierJustering AF Flashhovedet Montering OG Afmontering AF FlashenIndstilling AF Flashens Udlysningsvinkel VidvinkelforsatsLCD-DISPLAY Belysning TTL funktionKontinuerlig Optagelse Manuel Indstilling AF FlashLukkertidsprioriteret indstilling Blændeprioriteret indstillingSynkronisering PÅ Hurtige Lukkertider FP Flash Synkronisering MED Andet LukkergardinReduktion AF Røde Øjne Fungerer ikke med model SA-300Eksponeringskorrektion PILOT-LYSMULTI-FLASH Funktion Bounce Flash indirekte flash Trådløs Flash Ikke med SD9Næroptagelser Kontrolsystem indstillingKameraer uden indbygget flash SD10 Slave-flashNormal Slave-flash Specifikationer Udvalgte Slave-flashVoorzorgsmaatregelen Omschrijving van de onderdelenExterne onderdelen Instelknoppen/toetsenHet inleggen van de batterijen BatterijenHet afstellen van de flitskop Het instellen van de zoomreflector Het bevestigen en verwijderen van de flitserGroothoek diffusor TTL DDL Auto Mode Handmatige instelling M modeVerlichting van het LCD display Sluitertijd voorkeuzeHandmatige flitsinstelling Maximale prestaties bij continu fotograferenFP Flits behalve SA-300 Synchronisatie van het 2e sluitergordijn Rode-ogen reductieModel / Testflits BelichtingscompensatieMeervoudig flitsen Indirect flitsenIndien de flitser van de camera wordt gebruikt䟺SA-7 en SA-9 Draadloos flitsen Niet voor SD9Camera’s zonder ingebouwde flitser SD10 Slave functie Technische gegevens Voorkeuze van de slave flitser5Hz 100 128 199 EF-500 Super EO 03 ∟