Sigma EF-500 manual Control System Change, When Built-in Flash is Used SA-7 and SA-9

Page 23

Control System Change

Control System of “Wireless Flash” is different for each camera. First it is necessary to attach the flashgun to the camera for activating the control system. If this operation is neglected, wireless function may not work when flashgun is separated from the camera.

1.Attach the flashgun to the camera and turn on the power switch of the flashgun and camera.

2.Press the shutter button of camera halfway. (The camera and flashgun communicate and control system will be switched automatically.)

3.Turn off the power switch of the flashgun and camera.

When Built-in Flash is Used (SA-7 and SA-9)

1.Press the MODE button to select the mark.

2.Press the SEL button to make the channel indicator blink.

3.Press the + button or – button to set the channel.

4.Press the SEL button to stop the indicator blinking.

5.Place the EF-500 DG SUPER SA-N at the desired position.

Do not place the flash unit within the picture area.

■ Please be set the flash unit between 0.5m 5m (1.6 ~16ft) from the subject, and set the camera body between 1m 5m (1.6~16ft) from the subject.

Be sure to set the camera’s flash mode to “Wireless Flash Mode”, and set the channel number on the EF-500 DG SUPER SA-N Flash unit to the same channel number as that you set on the camera. Otherwise, the EF-500 DG SUPER SA-N and your camera will not communicate with each other and the EF-500 DG SUPER SA-N will not fire, when you take picture.

6.Pop-up the camera’s built-in flash, and then after both flashes are fully charged, press the shutter button to take the picture.

AF Auxiliary Light on the EF-500 DG SUPER SA-N will blink, when the flash unit charged and is ready to fire.

The EF-500 DG SUPER SA-N will fire when the built-in flash fires. The camera’s built-in flash is fired only to control the EF-500 DG SUPER SA-N only. The flash lighting of the subject is done by the EF-500 DG SUPER SA-N. The camera will control the flash power level, as a TTL mode flash, to Obtain correct exposure.

Cameras not equipped with built-in flash used (SD10)

For Wireless flash two pieces of EF-500 DG SUPER SA-N will be necessary. In this instruction, we call a flash unit, which is attached to the camera body “Master unit ”, and we call a flash unit at a remote position “Slave unit”.

Master unit Setting

1.Attach the flash unit to the camera.

2.Press the MODE button to select mark.

3.Press SEL button, to make the channel indicator blink on the display.

4.Press + or – button to set the desired channel number.

5.Press the SEL button several times until the display stops blinking.

Slave unit Setting

6.Press the MODE button to select .

7.Press SEL button, to make the channel indicator blink, on the display.

8.Press + or – button to choose the same channel number as set on the Master unit.

9.Press the SEL button several times until the indicator stops blinking.

10.Place the Slave unit at the desired position.

11.Check that both flashes are fully charged.

Ready light lamp will light, and the AF Auxiliary lamp will blink to indicate that the flash is ready for shooting.

12.Adjust the focus on the subject, and take the picture.

23

Image 23
Contents EF-500DG Super 12 13 14 15 EF-500 DG Super SA-N 䟺1䝞䞀䜼䟻 䜿䝇䝌 䜯䝥䝭 TTL 䝳䜨䝍 䝑䝯䛱䛪䛊䛬Page 䝢䝏䝩䜦䝯 䜻䝷䜳䝱 䝦䝋䝮䝷䜴 䜪䝷䜽 䜽䝰䞀䝚 SEL SD9 SD10 EF-500 DG Super SA-N TTL ッ䛮䜦䝙䝃䞀 䞀䝗䜽䛱䛪䛊䛬 Precautions Description of the Parts About the BatteryBattery Loading Adjusting the Flash HeadCase of use with Sigma SD9 SD10 Setting of Flash Coverage AngleAttaching and Removing the Flash to and from the Camera Wide PanelOr a service station LCD Panel Illumination Shutter Speed Priority SettingAperture Priority Setting When used with M ModeManual Flash Operation Limits of Continuous ShootingExposure Compensation Second Curtain SynchronizationRED-EYE Reduction Modeling FlashClose-up Exposures Multi Flash ModeWireless Flash Except SD9 Bounce FlashControl System Change When Built-in Flash is Used SA-7 and SA-9Designated Slave Flash Slave FlashNormal Slave Flash Specifications Deutsch VorsichtsmaßnahmenEinstellen des Blitzkopfes Beschreibung der TeileBatteriehinweise Einlegen der BatterienWeitwinkelstreuscheibe Anbringen und Abnehmen des BlitzgerätesEinstellen des Ausleuchtwinkels Zoomreflektor Autorisierten Sigma Service TTL Blitzautomatik Beleuchtung DER LCDKurzzeitblitzsynchronisation FP außer SA-300 Grenzen der SerienauslösungManueller Blitzbetrieb Belichtungskorrektur Synchronisation auf den zweiten VerschlussvorhangReduzierung roter Augen EinstelllichtKabelloses Blitzen Ausser SD9 StroboskopbetriebIndirektes Blitzen Einsatz an Kameras ohne eingebauten Blitz SD10 Wechsel der SystemsteuerungUnter Einsatz des eingebauten Blitzgerätes 䟺SA-7 und SA-9䟻 Kabellose Zündung bestimmter „Slave Geräte „Slave GerätNormaler „Slave Geräte Betrieb Technische Daten Français Mise EN Place DES Piles Description DES ElementsAlimentation Electrique Elargisseur Dangle Ajustement DE LA Tete FlashMise EN Place ET Retrait DU Flash Reglage DE Langle DE CouvertureRetro Eclairage DE Lecran LCD Mode de priorité à la vitesseMode de priorité à louverture Mode manuel MFlash Haute Vitesse FP sauf SA-300 Mode Operatoire EN Flash ManuelLimites DES Prises DE VUE Consecutives AU Flash Correction Dexposition Synchronisation SUR LE Deuxieme RideauReduction DE Leffet Yeux Rouges Flash PredictifPrise de vue rapprochée Mode DE Flash Stroboscopique Multi FlashFlash Indirect Flash Sans Cordon Sauf SD9Utilisation dun boîtier dépourvu de flash intégré SD10 Initialisation du système de contrôleUtilisation avec le flash intégré SA-7 et SA-9䟻 Flash esclave désigné Flash esclaveFlash esclave Normal Préparation du flash de contrôle Caracteristiques TechniquesAdvertencia Cuidado PrecaucionesCarga DE LAS Pilas Descripción DE LAS PartesAcerca DE LAS Pilas Ajustar EL Angulo DE Cobertura DEL Flash Ajuste DEL Cabezal DEL FlashMontar Y Desmontar EL Flash a LA Camara Ajuste para la prioridad de velocidad Pantalla AngularIluminación DE LA Pantalla LCD Flash Automático TTLCuando se utiliza con el Modo M Limitaciones DEL Disparo ContinuoOperación CON EL Flash Manual Ajuste para prioridad de diafragmaLUZ DE Modelado Sincronización CON LA Segunda CortinillaReduccion DE Ojos Rojos Exposiciones de Aproximación Compensación DE ExposiciónModo DE Multi Flash Estroboscópico Flash ReflejadoLas cámaras que no lleven flash incorporado SD10 Sistema de Control de CambiosControl Remoto DEL Flash Excepto SD9 Al emplear el flash de la propia cámara SA-7 y SA-9䟻Designación del flash esclavo Flash esclavoFlash esclavo Normal Para que la cantidad de salida parpadee EspecificacionesDescrizione Delle Parti AttenzioneCollegare E Separare IL Flash Dalla Macchina BatteriaCaricamento Delle Batterie Regolazione Della Testa DEL FlashIlluminazione DEL Display LCD Regolazione Dellangolo DI Copertura DEL FlashPannello Wide Limitazioni Quando SI Scatta in Sequenza Flash Automatico TTLSincronizzazione Della Seconda Tendina Flash ManualeFP Flash Flash AD Alta Velocità Eccetto SA-300 Modalità Multi Flash Flash DI RiempimentoCompensazione DELL’ESPOSIZIONE Cambiamento del Sistema di Controllo Flash IndirettoUso con le fotocamere non dotate di flash incorporato SD10 Uso del flash incorporato della䟺SA-7 e SA-9䟻Scegliere i flash secondari Flash ausiliarioFlash ausiliario normale Specifiche Beskrivelse AF Flashens Dele BemærkMontering OG Afmontering AF Flashen Vedr BatterierIsætning AF Batterier Justering AF FlashhovedetTTL funktion Indstilling AF Flashens UdlysningsvinkelVidvinkelforsats LCD-DISPLAY BelysningBlændeprioriteret indstilling Kontinuerlig OptagelseManuel Indstilling AF Flash Lukkertidsprioriteret indstillingFungerer ikke med model SA-300 Synkronisering PÅ Hurtige Lukkertider FP FlashSynkronisering MED Andet Lukkergardin Reduktion AF Røde ØjneMULTI-FLASH Funktion PILOT-LYSEksponeringskorrektion Kontrolsystem indstilling Bounce Flash indirekte flashTrådløs Flash Ikke med SD9 NæroptagelserNormal Slave-flash Slave-flashKameraer uden indbygget flash SD10 Udvalgte Slave-flash SpecifikationerInstelknoppen/toetsen VoorzorgsmaatregelenOmschrijving van de onderdelen Externe onderdelenHet afstellen van de flitskop BatterijenHet inleggen van de batterijen Groothoek diffusor Het bevestigen en verwijderen van de flitserHet instellen van de zoomreflector Sluitertijd voorkeuze TTL DDL Auto ModeHandmatige instelling M mode Verlichting van het LCD displayFP Flits behalve SA-300 Maximale prestaties bij continu fotograferenHandmatige flitsinstelling Belichtingscompensatie Synchronisatie van het 2e sluitergordijnRode-ogen reductie Model / TestflitsIndirect flitsen Meervoudig flitsenCamera’s zonder ingebouwde flitser SD10 Draadloos flitsen Niet voor SD9Indien de flitser van de camera wordt gebruikt䟺SA-7 en SA-9 Slave functie Voorkeuze van de slave flitser Technische gegevens5Hz 100 128 199 EF-500 Super EO 03 ∟