B&K 8510 instruction manual Remote Operation Mode, IT-E131 RS232 Communication cable

Page 36

		CW Mode Regulation			0-100W		±(1%+0.1%FS)			1mW
	Input current ≥FS 10%
	Input current ≥FS 10%				100-600W		±(1%+0.1%FS)			100mW
Input Voltage≥FS 10%）					100-600W		±(1%+0.1%FS)			100mW
Input Voltage≥FS 10%）
		Current Measurement			0-12A		±(0.1% + 0.1%FS)			1mA

					0-120A		±(0.2%+0.15%FS)			10mA
					0-120A		±(0.2%+0.15%FS)			10mA

		Voltage Measurement			0-18V		±(0.02% + 0.02%FS)			1mV

					0-120V		±(0.02% + 0.025%FS)			10mV
					0-120V		±(0.02% + 0.025%FS)			10mV
		Power Measurement			0-100W		±(1%+0.1%FS)			1mW
		Input current≥FS 10%			0-100W		±(1%+0.1%FS)			1mW

					100-600W		±(1%+0.1%FS)			100mW
Input Voltage≥FS 10%）					100-600W		±(1%+0.1%FS)			100mW

						Input=0.8-120V		Max measurement capacity= 999A/H
	Battery testing function					Input=0.8-120V		Max measurement capacity= 999A/H
	Battery testing function						Resolution =10mA		Timer range=1~60000sec
							Resolution =10mA		Timer range=1~60000sec
		Transition Mode			Range o Frequency 0.1Hz-1kHz				Frequency error rate＜0.5%
		Weight					30.8 lb. (14kg)

NOTE: Specifications and information are subject to change without notice. Please visit www.bkprecision.com for the most current product information.

Remote Operation Mode

The DB9 connector in the rear panel of the electronic load can be connected to a RS-232 or USB interface via a communication cable. The following information may help you to know how to control the input of electronic load through PC.

1 Communication cable

IT-E131 RS232 Communication cable

The DB9 interface connector on the rear panel of electronic load is TTL voltage level; you can use the communication cable (IT-E131) to connect the DB9 interface connector of the electronic load and the RS-232 interface connector of computer for the communication.

	IT-E131 communication
PC	cable	Load
PC		Load

COMPUTER

IT IT-E131 ISOLATED COMMUNICATION CABLE

RS232 ISOLATION TTL(5V)

859666668889942311

RX

TX

INSTRUMENT

IT-E132 USB Communication cable

36

Image 36

Contents Instruction Manual Programmable DC Electronic Load Table of Contents Warranty Information Safety Symbols Quick Reference Front PanelRear Panel Front Panel DisplayImmediate Action Keys Front Panel MenusKey Pad TranPOWER-ON Recall Menu OperationADC Update Rate High Lowdefault Options and Accessories General InformationDocument Orientation Getting Started MapFeatures and Capabilities AccessoriesDescription Front Panel ControlsConstant Resistance CR Mode Constant Voltage CV ModeRemote Programming Operating ModesConstant Power CW Mode Transient OperationContinuous Trigger Mode List OperationPulse Triggered Operation Input ControlShort On/Off Protection Features Input On/OffOperation Range Over VoltageOver Power Over TemperaturePin trigger and remote sensing connectors Remote Sense Function and Trigger FunctionSaving and Recalling Settings Wiring diagram for remote senseBattery Testing OperationVon/Voff Operation Action for set Von/Voff valueInstallation InspectionLocation Power Cord Outline DiagramBench Operation Input ConnectionsCheckout Procedure Turn-On CheckoutIntroduction Trigger and Remote Sensing ConnectionsFront Panel Operation Case of TroubleDisplay Front Panel DisplayPower Set set up a constant current from 0 to Max currentExample Function keysSet set up a constant power from 0 to Max power Set set up a constant resistance from 0.1Ω to 4000ΩPOWER=*.***W 000VTransition Testing Operation Set set up a constant voltage from 1.5V to Max voltageOn/Off input setting Shift + StoreTransition Parameter Setting Continuous Transient OperationPulse Transient Operation Toggled Transient Operation StepsList Operation Automatic Testing Function of Electronic Load Edit the Testing FileQuick Recall Function Enter Automatic Testing Setting the Resolution and number of decimal pointsSpecifications Range Accuracy ResolutionRemote Operation Mode Communication cableIT-E131 RS232 Communication cable IT-E132 USB Communication cableCommunication between electronic load and PC Frame FormatIT-E132 communication 2AH Selecting the Remote control mode（20H） Communication ProtocolSetting / Reading max input voltage（22H/23H） Setting / Reading the max input current .（24H/25H）Selecting the input on/off state （21H） Setting / Reading max input power（26H/27H） Setting / Reading CC mode current value（2AH/2BH） Setting / Reading CV mode voltage value.（2CH/2DH）Setting / Reading CW mode watt value（2EH/2FH） Setting / Reading CR mode resistance value（30H/31H） 26th byte Sum code Setting /Reading the list repeat mode CH/3DH Setting / Reading the number of list steps EH/3FHSetting / Reading List file name 48H/49H Setting / Reading timer value of for Load on 50H/51H） Save / Get list file in appointed area. CH/4DHSetting communication address 54H Enable/Disable Local control mode HSelecting / Reading trigger source H/59H Sending a trigger signal to trigging the electronic load AH Reading input voltage, current, power and relative state FHEnter the calibration mode（60H） BITGetting the calibration mode state（61H） Calibrate voltage value（62H）Setting / Reading calibration information（67H/68H） Calibrate current value（64H）Store the calibration data to EEPROM（66H） Restore the factory default calibration data（69H） For example：Reading information in bar code 6BH Setting information of bar code（6CH） Service Information Limited One-Year WarrantyDeclaration of CE Conformity Savi Ranch Parkway Yorba Linda, CA