B&K 8510 General Information, Document Orientation, Getting Started Map, Options and Accessories

Page 11

ON	When users choose the timer state ON, and then turn on the electronic
	load input, the LOAD ON TIMER will start working, and when the LOAD
	ON TIMER is reach the setup time, the electronic load input will turn off
	automatically,.

OFF<DEFAULT>

TIMER SET Setting time of LOAD ON timer.

EXIT

EXIT

General Information

Document Orientation

This manual describes the operation of the model 8510 DC Electronic Load. Unless otherwise noted, all units will be referred to by the description "electronic load" throughout this instruction manual. The following documents and software are shipped with your electronic load. This User's Guide (this document), contains installation, checkout, front panel information and detailed programming information.

The Getting Started Map will help you find the information you need to complete the specific task that you want to accomplish. Refer to the table of contents or index of each guide for a complete list of the information contained within.

Getting Started Map

Task	Where to find information
Checking out the unit	Instruction manual
Verifying proper operation
Using the front panel
Calibrating the unit

Using the front panel	Instruction manual
Front panel keys
Front panel examples

Using the programming interface	Instruction manual
RS-232 interface

Remote operation mode	Instruction manual
Protocol information

Controller Program and Software driver:	CD-ROM
Power View PV-8500 software
Calibration PC-8500 software

Options and Accessories

Options

11

Image 11

Contents Instruction Manual Programmable DC Electronic Load Table of Contents Warranty Information Safety Symbols Front Panel Quick ReferenceFront Panel Display Rear PanelTran Immediate Action KeysFront Panel Menus Key PadMenu Operation POWER-ON RecallADC Update Rate High Lowdefault Getting Started Map Options and AccessoriesGeneral Information Document OrientationFront Panel Controls Features and CapabilitiesAccessories DescriptionOperating Modes Constant Resistance CR ModeConstant Voltage CV Mode Remote ProgrammingContinuous Constant Power CW ModeTransient Operation Pulse Trigger ModeList Operation Short On/Off Triggered OperationInput Control Over Voltage Protection FeaturesInput On/Off Operation RangeRemote Sense Function and Trigger Function Over PowerOver Temperature Pin trigger and remote sensing connectorsWiring diagram for remote sense Saving and Recalling SettingsOperation Battery TestingAction for set Von/Voff value Von/Voff OperationLocation InstallationInspection Input Connections Power CordOutline Diagram Bench OperationTrigger and Remote Sensing Connections Checkout ProcedureTurn-On Checkout IntroductionFront Panel Display Front Panel OperationCase of Trouble DisplayFunction keys PowerSet set up a constant current from 0 to Max current Example000V Set set up a constant power from 0 to Max powerSet set up a constant resistance from 0.1Ω to 4000Ω POWER=*.***WShift + Store Transition Testing OperationSet set up a constant voltage from 1.5V to Max voltage On/Off input settingPulse Transient Operation Transition Parameter SettingContinuous Transient Operation Steps Toggled Transient OperationList Operation Quick Recall Function Automatic Testing Function of Electronic LoadEdit the Testing File Enter Setting the Resolution and number of decimal points Automatic TestingRange Accuracy Resolution SpecificationsIT-E132 USB Communication cable Remote Operation ModeCommunication cable IT-E131 RS232 Communication cableIT-E132 communication Communication between electronic load and PCFrame Format 2AH Communication Protocol Selecting the Remote control mode（20H）Selecting the input on/off state （21H） Setting / Reading max input voltage（22H/23H）Setting / Reading the max input current .（24H/25H） Setting / Reading max input power（26H/27H） Setting / Reading CW mode watt value（2EH/2FH） Setting / Reading CC mode current value（2AH/2BH）Setting / Reading CV mode voltage value.（2CH/2DH） Setting / Reading CR mode resistance value（30H/31H） 26th byte Sum code Setting / Reading the number of list steps EH/3FH Setting /Reading the list repeat mode CH/3DHSetting / Reading List file name 48H/49H Save / Get list file in appointed area. CH/4DH Setting / Reading timer value of for Load on 50H/51H）Selecting / Reading trigger source H/59H Setting communication address 54HEnable/Disable Local control mode H Reading input voltage, current, power and relative state FH Sending a trigger signal to trigging the electronic load AHBIT Enter the calibration mode（60H）Calibrate voltage value（62H） Getting the calibration mode state（61H）Store the calibration data to EEPROM（66H） Setting / Reading calibration information（67H/68H）Calibrate current value（64H） Reading information in bar code 6BH Restore the factory default calibration data（69H）For example： Setting information of bar code（6CH） Limited One-Year Warranty Service InformationDeclaration of CE Conformity Savi Ranch Parkway Yorba Linda, CA