B&K 8510 instruction manual Save / Get list file in appointed area. CH/4DH

Page 47

1st byte

Start bit ( AAH )

2nd byte

Address (0—0XFE)

3rd byte

Command 48H/49H

 

 

 

From 4th to 13th byte

LIST file name (ASSIC code )

From 14th to 25th byte

System reserve

 

 

26th byte

Sum code

23. Selection / Reading the memory space mode for storing list steps. (4AH/4BH)

1st byte

Start bit ( AAH )

2nd byte

Address (0—0XFE)

3rd byte

Command4AH/4BH

 

 

 

4th byte

partition mode (1 2 4 8)

From 5th to 25th byte

System reserve

26th byte

Sum code

24. Save / Get list file in appointed area.. (4CH/4DH)

1st byte

Start bit ( AAH )

2nd byte

Address (0—0XFE)

3rd byte

Command4CH/4DH

 

 

 

4th byte

Storing area 1 ~ 8)

From 5th to 25th byte

System reserve

26th byte

Sum code

25. Setting / Reading min voltage value in battery testing mode.4EH/4FH

1st byte

Start bit ( AAH )

2nd byte

Address (0—0XFE)

3rd byte

Command4EH/4FH

 

 

 

4th byte

The lowest byte of voltage value.

5th byte

The lower byte of voltage value.

6th byte

The higher byte of voltage value.

7th byte

The highest byte of voltage value.

From 8th to 25th byte

System reserve

26th byte

Sum code

26. Setting / Reading timer value of FOR LOAD ON (50H/51H

1st byte

2nd byte

3rd byte

4th byte

Start bit ( AAH )

Address (0—0XFE)

Command50H/51H

The lowest byte of time value in timer. (1 represent 1S)

47

Image 47
Contents Instruction Manual Programmable DC Electronic Load Table of Contents Warranty Information Safety Symbols Front Panel Quick ReferenceFront Panel Display Rear PanelTran Immediate Action KeysFront Panel Menus Key PadMenu Operation POWER-ON RecallADC Update Rate High Lowdefault Getting Started Map Options and AccessoriesGeneral Information Document OrientationFront Panel Controls Features and CapabilitiesAccessories DescriptionOperating Modes Constant Resistance CR ModeConstant Voltage CV Mode Remote ProgrammingContinuous Constant Power CW ModeTransient Operation Pulse Trigger ModeList Operation Short On/Off Triggered OperationInput Control Over Voltage Protection FeaturesInput On/Off Operation RangeRemote Sense Function and Trigger Function Over PowerOver Temperature Pin trigger and remote sensing connectorsWiring diagram for remote sense Saving and Recalling SettingsOperation Battery TestingAction for set Von/Voff value Von/Voff OperationLocation InstallationInspection Input Connections Power CordOutline Diagram Bench OperationTrigger and Remote Sensing Connections Checkout ProcedureTurn-On Checkout IntroductionFront Panel Display Front Panel OperationCase of Trouble DisplayFunction keys PowerSet set up a constant current from 0 to Max current Example000V Set set up a constant power from 0 to Max powerSet set up a constant resistance from 0.1Ω to 4000Ω POWER=*.***WShift + Store Transition Testing OperationSet set up a constant voltage from 1.5V to Max voltage On/Off input settingPulse Transient Operation Transition Parameter SettingContinuous Transient Operation Steps Toggled Transient OperationList Operation Quick Recall Function Automatic Testing Function of Electronic LoadEdit the Testing File Enter Setting the Resolution and number of decimal points Automatic TestingRange Accuracy Resolution SpecificationsIT-E132 USB Communication cable Remote Operation ModeCommunication cable IT-E131 RS232 Communication cableIT-E132 communication Communication between electronic load and PCFrame Format 2AH Communication Protocol Selecting the Remote control mode(20H)Selecting the input on/off state (21H) Setting / Reading max input voltage(22H/23H)Setting / Reading the max input current .(24H/25H) Setting / Reading max input power(26H/27H) Setting / Reading CW mode watt value(2EH/2FH) Setting / Reading CC mode current value(2AH/2BH)Setting / Reading CV mode voltage value.(2CH/2DH) Setting / Reading CR mode resistance value(30H/31H) 26th byte Sum code Setting / Reading the number of list steps EH/3FH Setting /Reading the list repeat mode CH/3DHSetting / Reading List file name 48H/49H Save / Get list file in appointed area. CH/4DH Setting / Reading timer value of for Load on 50H/51H)Selecting / Reading trigger source H/59H Setting communication address 54HEnable/Disable Local control mode H Reading input voltage, current, power and relative state FH Sending a trigger signal to trigging the electronic load AHBIT Enter the calibration mode(60H)Calibrate voltage value(62H) Getting the calibration mode state(61H)Store the calibration data to EEPROM(66H) Setting / Reading calibration information(67H/68H)Calibrate current value(64H) Reading information in bar code 6BH Restore the factory default calibration data(69H)For example: Setting information of bar code(6CH) Limited One-Year Warranty Service InformationDeclaration of CE Conformity Savi Ranch Parkway Yorba Linda, CA