INSTALLATION REQUIREMENTS
Tools and Parts
Assemble the necessary tools and supplies before beginning the washer installation. The parts supplied are in the washer drum.
Tools needed for connecting the water inlet hoses
■Pliers (that open to 1⁹⁄₁₆ in. [39.5 mm])
■Flashlight (optional)
Tools needed for installation
■Open end wrench 17 mm and 13 mm
■Level
■Wood block (2" x 4")
■Ruler or measuring tape
Parts supplied:
13 in. (33 cm) to the height of your unit for a total height of approximately 51 in. (130 cm).
Optional pedestal
To order, call the dealer from whom you purchased your washer or refer to the “Assistance or Service” section of this manual. (Ask for Part Number LAB2700PO [Meteorite].)
Beaded strap | Transport bolt hole plug (4) |
Stack Kit
Are you planning to stack your KitchenAid washer and dryer? To do so you will need to purchase a Stack Kit.
To order, call the dealer from whom you purchased your dryer or refer to the “Assistance or Service” section of this manual. Ask for Part Number 8541503.
Alternate Parts
Your installation may require additional parts. If you are interested in purchasing one of the items listed here, call the
If You Have | You Will Need to Buy |
|
|
Laundry tub or | Sump pump system (if not already |
standpipe taller | available) |
than 96 in. (2.4 m) |
|
|
|
Overhead sewer | Standard 20 gal. (76 L), 30 in. (76.2 cm) |
| tall drain tub or utility sink and sump |
| pump (available from local plumbing |
| suppliers) |
|
|
Floor drain | Siphon break, Part Number 285834; |
| additional drain hose Part |
| Number 8318155; and connector kit, |
| Part Number 285835 |
|
|
Drain hose too | 4 ft drain hose extension kit, Part |
short | Number 285863 |
|
|
Water faucets | 2 longer water fill hoses: |
beyond reach of | 6 ft (1.8 m) Part Number 76314, |
fill hoses | 10 ft (3.0 m) Part Number 350008 |
Options
Pedestal
Are you placing the washer on a pedestal? You may purchase a pedestal separately for this washer. This pedestal will add about
Location Requirements
Selecting the proper location for your washer improves performance and minimizes noise and possible washer “walk.”
Your washer can be installed under a custom counter, or in a basement, laundry room, closet, or recessed area. (See “Drain System.”)
Companion appliance location requirements should also be considered. Proper installation is your responsibility.
You will need
■A water heater set to deliver 120°F (49°C) water to the washer.
■A grounded electrical outlet located within 5 ft (1.5 m) of where the power cord is attached to the back of the washer. (See “Electrical Requirements.”)
■Hot and cold water faucets located within 4 ft (1.2 m) of the hot and cold water fill valves, and water pressure of
■A level floor with a maximum slope of 1 in. (2.5 cm) under entire washer. Installing the washer on carpeting is not recommended.
■A sturdy and solid floor to support the washer with a total weight (water and load) of 400 lbs (180 kg).
Do not operate your washer in temperatures below 32°F (0°C). Some water can remain in the washer and can cause damage in low temperatures.
Installation clearances
■The location must be large enough to allow the washer door to be fully opened.
■Additional spacing should be considered for ease of installation and servicing.
■Additional clearances might be required for wall, door, and floor moldings.
■Additional spacing of 1 in. (2.5 cm) on all sides of the washer is recommended to reduce noise transfer.
■Companion appliance spacing should also be considered.
4