Note: |
|
|
|
|
|
| Note: |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| ||
The maximum permitted number of 90°Please check with the Authority Having |
| CAUTION |
|
| ||||||||||||||||||||
elbows | (including | this side | exhaust | kit) | Jurisdiction | in | your area | to | verify | if a | gas |
|
| |||||||||||
is | four! |
|
|
|
|
|
| dryer | can | be | installed | in | your | mobile |
| Do not slide dryer across | the floor if | |||||||
|
|
|
|
|
| home. | Once that | has | been | verified, |
| |||||||||||||
|
|
|
|
|
|
|
|
| ||||||||||||||||
i | Special | tool for cutting | the hole ininstallation | of | the | dryer shall | conform to heightnadjustable feet have | been | ||||||||||||||||
| prepared | side | panel is | required. |
| the | Manufactured | Home | Construction | extended. Feet and/or dryer base | ||||||||||||||
| Contact | local | dealer! |
|
|
| and | Safety | Standard, | Title 24 CFR, Partmay be damaged if dryer | is slid | |||||||||||||
Bottom | exhaust | kit |
|
|
| 3280 | {formerly the Federal Standard for | across | floor with heightnadjustable | |||||||||||||||
|
|
| Mobile | Home | Construction and | Safety, |
| feet extended. |
|
| ||||||||||||||
|
|
|
|
|
|
|
|
|
| |||||||||||||||
|
|
|
|
|
|
|
| Title 24, HUD (Part 280)}, and/or |
|
| 10. Position and then level | the .dryer | ||||||||||||
|
|
|
|
|
|
|
| Standard | CAN/CSAnZ240 | MH. |
|
|
| |||||||||||
|
|
|
|
|
|
|
| Please use mobile home kit number |
|
|
|
| ||||||||||||
|
|
|
|
|
|
|
| WTZ | 1275 for | means | to | secure the |
|
|
|
| ||||||||
|
|
|
|
|
|
|
| dryer | to | the | structure. |
|
|
|
|
|
|
|
|
|
| |||
|
|
|
|
|
|
|
| See | page 9 •Exhaust | Air | Connection" |
|
|
|
| |||||||||
|
|
|
|
|
|
|
| for the exhaust duct installation |
|
|
|
|
|
| ||||||||||
|
|
|
|
|
|
|
| instructions. |
|
|
|
|
|
|
|
|
|
|
|
|
| |||
|
|
|
|
|
|
|
| The exhaust duct must be securely |
|
|
|
| ||||||||||||
|
|
|
|
|
|
|
| fastened | to a | noncombustible | portion |
|
|
|
| |||||||||
|
|
|
|
|
|
|
| of the | mobile | home structure | and must |
|
|
| ||||||||||
|
|
|
|
|
|
|
| not terminate beneath the mobile |
|
|
|
|
|
| ||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
| |||||||||||
part no.WTZ | 1270 |
|
|
| home. |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| ||||
Note: |
|
|
|
|
|
| An opening to the outside | must | be |
|
|
|
| |||||||||||
The maximum permitted number of 90°provided during installation. Insure that |
|
|
|
| ||||||||||||||||||||
elbows | (including | this side exhaust | kit) | the | free | area of the opening for the |
|
|
|
| ||||||||||||||
is | four! |
|
|
|
|
|
| introduction | of | outside | air is | not | less |
|
|
|
| |||||||
|
|
|
|
|
| than twice the area of the | dryer | exhaust |
|
|
| |||||||||||||
LP | - | Gas | Kit |
|
|
|
|
|
|
| ||||||||||||||
|
|
|
| outlet | or | use | at | least | a | 5 inch diameter |
|
|
| |||||||||||
|
|
|
|
|
|
|
| exhaust | or | at | least a | 225squarein |
|
|
|
|
|
|
| |||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
exhaust duct for the opening.
|
|
|
| Installation | \ step by step | |||
|
|
| 1. | Unpack the dryer. |
| |||
|
|
| 2. | Remove all objects from the drum. | ||||
|
|
| 3. | Check the dryer for visible |
| |||
|
|
|
|
| damage. |
|
|
|
|
|
| 4. | Position the dryer near the |
| |||
|
|
|
|
| installation | location. |
| |
|
|
|
| 5. | If required, have customer service | |||
|
|
|
| |||||
part | no.WTZ | 1280 |
|
| change the | door | hinges to | the left |
The | parts required | for the LP version | (see page | 6). |
|
| ||
can be obtained from your local dealer. 6. | If required, | have | customer | service | ||||
Please follow | the | installation |
|
|
|
|
The dryer should be level with all four feet firmly on the ground. The dryer must not wobble. If the dryer is not level or if it does wobble, th feet must be adjusted. Adjust the heightnadjustable feet until the dryer does not rock and is level,
instructions supplied by the appropriate manufacturer!
Note:
Dryer must be checked for proper operation whenever the gas connections have been broken
Left hinge kit
part no.WTZ 1260
The door catch can be reversed if necessary. The door is hinged on the right at the factory.
Pedestal Mounting Kit
part no.WTZ 1295
If mounting the dryer on the pedestal follow the instructions supplied with the pedestal.
an qualified technician (see page 7).
8.Install exhaust duct, if necessary. Follow the installation instructions supplied by the appropriate manufacturer!
iIf space is very restricted, it is
recommended to fit the initial parts of the exhaust duct to the dryer before the dryer is moved to its final installation location.
9.Move the dryer to its final location and align.
both frontntonback and sidentonside.
11.Connect the exhaust duct to the exhaust air outlet on the dryer.
12.Insert plug into the wall receptacle.
Mobile home kit
part no.WTZ 1275
9