Kohler 1199249-2-A manual Make Power Connections Remote, Complete the Installation, Remote Blower

Page 12

Typical Remote Blower Installation

Check Valve

Control Power Junction Box

Remote Blower

New Field Cable To Blower Motor

Power Supply Cable

Blower Motor Cord

Control Power Supply

Second Junction Box (added for Remote Blower)

8. Make Power Connections - Remote

WARNING: Risk of electric shock. To reduce the risk of electric shock, connect the control to a properly grounded Ground-Fault Circuit-Interrupter (GFCI) or Residual Current Device (RCD). This will provide additional protection against line-to-ground shock hazard. A dedicated 220-240 V, 20 A, 50/60 Hz circuit is required.

WARNING: Risk of electric shock. Make sure the power has been disconnected before performing the following procedures.

Ensure that the control power supply cord is properly routed to the control power junction box. The control power supply cord contains a brown wire (Line 1), a blue wire (Line 2), and a green wire with a yellow stripe (ground or earth).

Install a strain relief (not provided) for the power supply cable to the control power junction box.

Route the power supply cable to the control power junction box.

As required, strip the jacket and wire insulation on both cables to make the connections.

For installations in the USA, mark any white conductor in the supply power wiring with red or black tape as required by the NEC.

Connect service to the control power junction box.

Provide a separate equipment earthing or grounding conductor to the spare earth/ground lug located on the control power junction box. This conductor must not be connected to any current-carrying conductor. Follow local electrical codes.

Bond in accordance with national and local codes.

Clean the area of all dust and debris.

All wiring harnesses have been pre-wired at the factory. Ensure that all wires are securely fastened.

NOTE: Your wiring harness includes an antenna for the optional remote control. Do not alter or damage this antenna during installation.

9. Complete the Installation

Test Run the Bath

Fill the bath to a level at least 4(102 mm) above the top of the highest airjet.

Operate the bath for 5 minutes and check all bath piping connections for leaks. Check for leakage along the front, sides, and back of the bath.

For additional information on bath operation, see the Operating Instructionssection.

1199249-2-A

12

Kohler Co.

Image 12
Contents Installation and Care Guide Product Information Electrical RequirementsProduct Notices Features Tools and MaterialsPrepare the Blower Remote Site Product InformationPrepare the Blower Remote Site Prepare the Site AlcoveInstall the Bath Install the PlumbingCut the Banding Straps Typical Wiring Connection for North America Make Electrical Connections StandardDisconnect the Blower Motor Remote Remove the Blower Motor and Check ValvePrepare the Site Mount the Blower Motor and Check Valve Remote Manufacturer’s instructionsRoute the Power Cable Prepare the Blower for Remote InstallationConnect the New Power Cable at the Blower Motor Terminate the Cable at the Blower RemoteInstall the Blower Cord at the Control Remote Install the Second Junction Box on the ControlReconnect the Blower Motor Power Cord Reconnect the Blower New Power CableMake Power Connections Remote Complete the InstallationRemote Blower Test Run the BathComplete the Installation Finish the Installation Clean-up After InstallationImportant Safety Instructions Initiating a Manual Purge Cycle when desired Operating InstructionsStarting the Unit Selecting Air Flow ModesCare and Cleaning WarrantyCleaning Your User Keypad and Remote Control Maintaining the AirjetsWarranty For MexicoTroubleshooting Exceptions and RestrictionsTroubleshooting Symptoms Probable Causes Recommended ActionTroubleshooting Installations électriques requises Information sur le produitPréparer le souffleur Installation à distance Outils et matériauxCaractéristiques Information sur le produitPréparer le souffleur Installation à distance Préparer le site AlcôveEncastrer par le dessus Installer la baignoire Installer la plomberieCouper les sangles de retenue Effectuer les connexions électriques Standard Câblage typique pour lAmérique du NordDéconnecter le moteur du souffleur À distance Retirer le moteur du souffleur et le clapet de non-retourPréparer le site Selon les instructions du fabricant Préparer le souffleur pour une Installation à distance Finir le câble au souffleur À distanceAcheminer le câble d’alimentation Finir le câble au souffleur À distance Installer le cordon au niveau de la commande À distance Installer le deuxième boîtier de jonction sur la commande60 Hz 50 Hz Depuis le contrôle Reconnecter le cordon d’alimentation du moteur du souffleurTerminer l’installation Effectuer les connexions électriques À distanceMoteur-souffleur à distance Tester le fonctionnement de la baignoireTerminer l’installation Nettoyer après l’installationInstructions Importantes sur la sécurité 1199249-2-A Français-14 Kohler CoInstructions d’utilisation Démarrer l’appareilSélectionner les modes de débit d’air Arrêter la baignoireMaintenance des jets d’air Nettoyer le clavier utilisateur et la télécommandeEntretien et nettoyage GarantieGarantie Limitée D’UN AN GarantieDépannage Symptômes Causes probables Action recommandée Dépannage1199249-2-A Français-20 Kohler Co Kohler Co Français-21 1199249-2-A Información sobre el producto Requisitos eléctricosHerramientas y materiales Prepare el soplador lugar remotoAvisos sobre el producto CaracterísticasPrepare el soplador lugar remoto Prepare el sitio Encajonado entre tres paredesDe sobreponer Instale la bañera Corte las cintasInstale la plomería Realice las conexiones eléctricas Estándar Conexión de cableado típica para NorteaméricaDesconecte el motor soplador Remoto Retire el motor soplador y la válvula de retenciónPrepare el sitio Monte el motor soplador y la válvula de retención Remoto Del fabricanteTermine el cable en el soplador Remoto Tienda el cable eléctricoPrepare el soplador para la instalación remota Conecte el cable de eléctrico nuevo al motor sopladorTermine el cable en el soplador Remoto Instale el cable del soplador al control Remoto 60 Hz 50 Hz Del controlInstale la segunda caja de empalmes en el control Vuelva a conectar el cable eléctrico del motor sopladorRealice las conexiones eléctricas Remoto Termine la instalaciónSoplador remoto Pruebe el funcionamiento de la bañeraTermine la instalación Acabe la instalaciónLimpieza después de la instalación Instrucciones importantes de seguridad Kohler Co Español-14 1199249-2-AInstrucciones de funcionamiento Puesta en marcha de la unidadSelección de los modos de flujo de aire Pare el funcionamiento de la bañeraCuidado y limpieza GarantíaInstrucciones de funcionamiento Mantenimiento de los jets de aireGarantía Limitada DE UN AÑO GarantíaGuía para resolver problemas Para MéxicoGuía para resolver problemas Síntomas Causas probables Acción recomendadaKohler Co Español-20 1199249-2-A 1199249-2-A Español-21 Kohler Co 1199249-2-A Kohler Co