Kohler 1199249-2-A Disconnect the Blower Motor Remote, Remove the Blower Motor and Check Valve

Page 8

Blower Motor

Mounting Screws

Elbow

Check

Valve

Cover

Junction Box

Baseboard

Screw

Control

To Blower Motor

Blower Motor

Electrical Plug

4. Disconnect the Blower Motor - Remote

NOTICE: This section applies only to installations in which the blower motor and check valve are being relocated.

NOTICE: Do not cut the blower piping for this installation.

NOTICE: You must relocate the check valve with the blower motor. Do not disconnect the check valve from the tee.

Remove the Blower Motor and Check Valve

Disconnect the blower motor electrical plug from the control.

Remove any cable ties that support the blower motor cord.

Remove and retain the screw holding the check valve to the PVC elbow.

Remove and retain the four screws from the baseboard.

Slide the blower motor and check valve away from the elbow, and remove the blower motor from the bath.

Prepare the Site

NOTE: Refer to the Prepare the Blower (Remote Site)section for blower relocation details.

Prepare the site where the blower motor will be installed. The site must be within 15’ (4.5 m) of the bath.

Install an access panel to service the blower motor.

Prepare the routing paths for the PVC piping and the new blower motor power cable. Follow all applicable codes.

1199249-2-A

8

Kohler Co.

Image 8
Contents Installation and Care Guide Product Notices Product InformationElectrical Requirements Features Tools and MaterialsPrepare the Blower Remote Site Product InformationPrepare the Blower Remote Site Prepare the Site AlcoveCut the Banding Straps Install the BathInstall the Plumbing Typical Wiring Connection for North America Make Electrical Connections StandardPrepare the Site Disconnect the Blower Motor RemoteRemove the Blower Motor and Check Valve Mount the Blower Motor and Check Valve Remote Manufacturer’s instructionsRoute the Power Cable Prepare the Blower for Remote InstallationConnect the New Power Cable at the Blower Motor Terminate the Cable at the Blower RemoteInstall the Blower Cord at the Control Remote Install the Second Junction Box on the ControlReconnect the Blower Motor Power Cord Reconnect the Blower New Power CableMake Power Connections Remote Complete the InstallationRemote Blower Test Run the BathComplete the Installation Finish the Installation Clean-up After InstallationImportant Safety Instructions Initiating a Manual Purge Cycle when desired Operating InstructionsStarting the Unit Selecting Air Flow ModesCare and Cleaning WarrantyCleaning Your User Keypad and Remote Control Maintaining the AirjetsWarranty For MexicoTroubleshooting Exceptions and RestrictionsTroubleshooting Symptoms Probable Causes Recommended ActionTroubleshooting Installations électriques requises Information sur le produitPréparer le souffleur Installation à distance Outils et matériauxCaractéristiques Information sur le produitPréparer le souffleur Installation à distance Encastrer par le dessus Préparer le siteAlcôve Couper les sangles de retenue Installer la baignoireInstaller la plomberie Effectuer les connexions électriques Standard Câblage typique pour lAmérique du NordPréparer le site Déconnecter le moteur du souffleur À distanceRetirer le moteur du souffleur et le clapet de non-retour Selon les instructions du fabricant Acheminer le câble d’alimentation Préparer le souffleur pour une Installation à distanceFinir le câble au souffleur À distance Finir le câble au souffleur À distance Installer le cordon au niveau de la commande À distance Installer le deuxième boîtier de jonction sur la commande60 Hz 50 Hz Depuis le contrôle Reconnecter le cordon d’alimentation du moteur du souffleurTerminer l’installation Effectuer les connexions électriques À distanceMoteur-souffleur à distance Tester le fonctionnement de la baignoireTerminer l’installation Nettoyer après l’installationInstructions Importantes sur la sécurité 1199249-2-A Français-14 Kohler CoInstructions d’utilisation Démarrer l’appareilSélectionner les modes de débit d’air Arrêter la baignoireMaintenance des jets d’air Nettoyer le clavier utilisateur et la télécommandeEntretien et nettoyage GarantieGarantie Limitée D’UN AN GarantieDépannage Symptômes Causes probables Action recommandée Dépannage1199249-2-A Français-20 Kohler Co Kohler Co Français-21 1199249-2-A Información sobre el producto Requisitos eléctricosHerramientas y materiales Prepare el soplador lugar remotoAvisos sobre el producto CaracterísticasPrepare el soplador lugar remoto De sobreponer Prepare el sitioEncajonado entre tres paredes Instale la plomería Instale la bañeraCorte las cintas Realice las conexiones eléctricas Estándar Conexión de cableado típica para NorteaméricaPrepare el sitio Desconecte el motor soplador RemotoRetire el motor soplador y la válvula de retención Monte el motor soplador y la válvula de retención Remoto Del fabricanteTermine el cable en el soplador Remoto Tienda el cable eléctricoPrepare el soplador para la instalación remota Conecte el cable de eléctrico nuevo al motor sopladorTermine el cable en el soplador Remoto Instale el cable del soplador al control Remoto 60 Hz 50 Hz Del controlInstale la segunda caja de empalmes en el control Vuelva a conectar el cable eléctrico del motor sopladorRealice las conexiones eléctricas Remoto Termine la instalaciónSoplador remoto Pruebe el funcionamiento de la bañeraLimpieza después de la instalación Termine la instalaciónAcabe la instalación Instrucciones importantes de seguridad Kohler Co Español-14 1199249-2-AInstrucciones de funcionamiento Puesta en marcha de la unidadSelección de los modos de flujo de aire Pare el funcionamiento de la bañeraCuidado y limpieza GarantíaInstrucciones de funcionamiento Mantenimiento de los jets de aireGarantía Limitada DE UN AÑO GarantíaGuía para resolver problemas Para MéxicoGuía para resolver problemas Síntomas Causas probables Acción recomendadaKohler Co Español-20 1199249-2-A 1199249-2-A Español-21 Kohler Co 1199249-2-A Kohler Co