Hitachi KM 12VC, KM 12SC Installing and Removing Bits, Installing bits, Removing bits

Page 10

English

INSTALLING AND REMOVING BITS

WARNING: Be sure to switch power OFF and disconnect the plug from the receptacle to avoid serious trouble.

1. Installing bits

(1)Remove the motor housing from base as follows.

(a)Open the lever. (Fig. 2)

(b)While holding the base, turn the motor housing counterclockwise.

(c)Turn it until the pin in the base is disengaged from the groove in the motor housing. Lift the motor housing free from the base.

(2)Clean and insert shank of bit into the collet chunk until shank bottoms, then back it out approximately 1/16” (approx. 2 mm).

(3)With the bit inserted and 16 mm wrench holding the armature shaft, use the 23 mm wrench to firmly tighten the collet chuck in a clockwise direction (viewed from under the router). (Fig. 3)

(4)When using the 1/4” diameter shank bit, replace the equipped collet chuck with the one for 1/4” diameter shank bit which is provided as the standard accessory.

CAUTION:

⬤Ensure that the collet chuck is firmly tightened after inserting a bit. Failure to do so will result in damage to the collet chuck.

2.Removing bits

When removing the bits, do so by following the steps for installing bits in reverse order.

Motor

Housing

Base

Lever

Fig. 2

23mm

Loosen Wrench

Bit

Collet

Chuck

Tighten

16mm Wrench

Fig. 3

10

Image 10

Contents Avertissement Router Toupie FresadoraAdvertencia Contents Important Safety Information Meanings of Signal WordsSafety General Safety RulesSpecific Safety Rules and Symbols English Make Them Available to Other Users Owners of this Tool USE of Extension CordFunctional Description SpecificationsName of Parts Applications Assembly and OperationPrior to Operation Installing bits Installing and Removing BitsRemoving bits Installing the motor housing Installing the Motor HousingHOW to USE the Router Adjusting depth of cutCentering the template guide adapter Adjusting the rotation speed Model M12VC onlyGuiding the router Cutting English Maintenance and Inspection Modifications Model M12VC, M12SC AccessoriesStandard Accessories Model KM12VC, KM12SCOptional Accessories …………… sold separately Informations Importantes DE SƒCURITƒ Signification DES Mots DõavertissementRegles Generale DE Securite SecuriteConserver CES Instructions Franais Regles DE Securite Specifiques ET Symboles Avertissement Utilisation Dõun Cordon DE Rallonge Calibre Minimum DES CordonsDescription Fonctionnelle NOM DES PartiesAvant Lõutilisation Installation de la mèche Installation ET Retrait DE LA MecheRetrait de la mèche Utilisation DE LA Toupie Installation DU Carter MoteurInstallation du carter moteur Réglage de la profondeur de coupeCentrage de l’adaptateur de guide de gabarit Réglage de la vitesse de rotation Modèle M12VC seulementGuidage de la toupie Coupe Remarque Entretien ET Inspection No. élément No. code No. utilisé Remarques Modèle M12VC, M12SC AccessoiresAccessoires Standard Modèle KM12VC, KM12SCAccessoires SUR Option Ééééé vendus sŽparŽment INFORMACIîN Importante Sobre Seguridad Significado DE LAS Palabras DE SE„ALIZACIîNNormas Generales DE Seguridad SeguridadGuarde Estas Instrucciones Espa-ol Normas Y SêMBOLOS ESPECêFICOS DE Seguridad Advertencia Otros Usuarios Propietarios DE Esta Herramienta Águarde Estas InstruccionesUTILIZACIîN DE UN Cable Prolongador DESCRIPCIîN Funcional NomenclaturaAplicaciones Antes DE LA OPERACIîNInstalación de las brocas INSTALACIîN Y EXTRACCIîN DE LAS BrocasExtracción de brocas CîMO Usar LA Fresadora INSTALACIîN DE LA Carcasa DEL MotorAjuste de la profundidad de corte Centrado del adaptador de guía de la plantilla Ajuste de la velocidad de rotación Modelo M12VC solamenteCómo guiar la fresadora Corte Nota Reemplazo de las escobillas Inspección de los tornillosInspección de la escobillas Fig Mantenimiento y reparaciónModificaciones Modelo M12VC, M12SC AccesoriosAccesorios ESTçNDAR Modelo KM12VC, KM12SCAccesorios Opcionales Ééééé de venta por separado M12VC M12SC KM12VC, KM12SC KM12VC KM12SC Hitachi Koki Canada Co Plunge Base Socle d’inclinaison Base de penetración Installing plunge base Meanings of Signal Words Replacing the BaseRemoving the fixed base Fig Stopper block Fig Adjusting depth of cut FigUpper limiting nuts Fig Cutting Signification DES Mots D’AVERTISSEMENT Remplacement DU SocleInstallation du socle d’inclinaison Retrait du socle fixe FigButée Fig Réglage de la profondeur de coupe FigEcrous de limite supérieure Fig Séparé Avance de la toupie Desmontaje de la base fija Fig Significado DE LAS Palabras DE SeñalizaciónReemplazo DE LA Base Instalación de la base de penetraciónBloque de tope Fig Cómo Usar LA RanuradoraAjuste de la profundidad de corte Fig Tuercas limitadora superior FigPrecaución Page Hitachi Koki Canada Co