RIDGID 700 manual Thread Size Adjustment Procedure, Changing posts For Straight Or Tapered Threads

Page 10

No. 700 Portable Power Drive

2.Pull knobs (Figure 7) of cam plate and rotate cam plate to desired pipe size marking on top of die head. Release knobs when locating pins drop into holes in selector plate.

No. 844

Drive Bar

Drive Shaft

Set Screws

Cam

Plate Knob

Cam

Plate KnobClamp

Screw

Figure 7 – No 141 Geared Threader (No. 161 Threader Similar)

Thread Size Adjustment Procedure

Grasp workholder and turn square end of drive shaft or turn gear case by hand to respective reference lines on guide post (Figure 8).

Standard Size Thread – Either one of the following two (2) reference lines may be used.

Reference Line 1: Set bottom surface of die head at red STANDARD line on pinion sleeve.

Reference Line 2: Set upper surface of die head which houses guide post even with STANDARD line at top end of guide post.

Oversize Thread: For oversize (shallow thread) set head at bottom line on guide post. This line is marked (2T OVER).

Undersize Thread: For undersize (deep throat) set head at top line on guide post. This line is marked (2T UNDER).

Changing posts For Straight Or Tapered Threads

(Figure 8)

1.Adjust threader to cut standard size threads using “STANDARD” reference line.

2.Remove screw from gear case at base of guide post.

Selector Plate

Die (Set of 5)

Die Head

Guide

 

Block

2T Under

StopLine

Screw

Standard

Red StopLIne

Line

2T Over

StandardLine

Line

 

Guide Post

Pinion

 

Sleeve

Screw

 

Gear Case

Selector

 

Plate Knob

 

 

Workholder

Figure 8 – No. 141 Geared Threader Showing Pinion Sleeve And Guide Post Reference Lines (No. 161 Geared Threader Similar)

3.Pull guide post up until guide block attached to selec- tor plate is disengaged from angle slot in guide post.

4.Turn guide post until straight slot faces inward for straight thread, or tapered slot inward for tapered thread. Figure 8 shows guide post set to cut tapered thread.

5.Engage guide block in slot and push guide post down into position.

6.Replace guide post screw.

Unit is now set to cut straight threads (NPSM or BSPP) or tapered threads (NPT or BSPT).

Changing Die Set

1.Remove stop screw (Figure 8) from selector plate.

2.Pull knobs (Figure 8) and rotate cam plate to CD mark on top of die head.

3.Remove worn die set (Figure 8) and insert new die set.

IMPORTANT: Be sure to replace complete die set. Die numbers must correspond with slot num- bers.

8

Ridge Tool Company

Image 10
Contents Portable Power Drive Table of Contents 700 Portable Power Drive Electrical Safety General Safety InformationWork Area Safety Personal SafetySpecific Safety Information Description, Specifications and Standard EquipmentThreading Capacity Specifications/Standard EquipmentAccessories Adapters for Drop Head Die HeadsPower Drive Inspection Tool and Work Area Set-Up Installing No -R Drop Head Die Head Threading Using Pipe Wrench As a Support Arm Operation Instructions For Threading With Geared ThreadersChanging posts For Straight Or Tapered Threads Thread Size Adjustment ProcedureChanging Die Set Threading With Geared Threaders Threading With Geared ThreaderMaintenance Instructions AccessoriesTool Storage Service and Repair Troubleshooting Wiring Schematic 230V with Line Filter Wiring Diagram 115/230VInstallation of Brush Lead Wires Standard Color Code European Color CodeSystème d’entraînement portatif n Table des matières Sécurité électrique Consignes générales de sécuritéSécurité du chantier Sécurité individuelleUtilisation et entretien de l’appareil Service après-venteConsignes de sécurité particulières Sécurité du système d’entraînementSpécifications et équipements de base Description, spécifications et équipements de baseCapacité de filetage Inspection du système d’entraînement AccessoiresAdaptateurs de têtes de filière amovibles Préparation de l’appareil et du chantier Le filetage avec têtes de filière amoviblesInstallation d’une tête de filière amovible n 12-R Le filetage avec les fileteuses démultipliées Filetage en utilisant une clé à tubes comme étrésillonRemplacement des filières Remplacement des poteaux pour filetage droit ou coniqueRéglage du filetage Le filetage avec les fileteuses démultipliées Le filetage avec fileteuse démultipliéeEntretien AccessoiresService après-vente et réparations Stockage de l’appareilDépannage Schéma de câblage 230V avec filtre antiparasite Installation des fils de balais moteurSchéma électrique 115V/230V Code couleur standard Code couleur européenAccionamiento Motorizado portátil No Información específica de seguridad ÍndiceInformación general de seguridad Descripción, especificaciones y equipo estándarSeguridad eléctrica Información general de seguridadSeguridad en la zona de trabajo Seguridad personalUso y cuidado de la máquina Información específica de seguridadServicio Descripción Descripción, especificaciones y equipo estándarSeguridad del Accionamiento Motorizado Especificaciones y equipo estándarAdaptadores para Cabezales de terrajas de cabeza abatible Inspección del Accionamiento MotorizadoAccesorios Roscadoras a engranajesPreparación de la máquina y de la zona de trabajo Figura 3 Instalación del Cabezal de terrajas No -R Coloque el Cabezal de Terrajas sobre el extremo del tubo Procedimiento para regular el tamaño de la rosca Cambio de postes para roscas rectas o roscas achaflanadasRecambio del juego de terrajas Roscado con Roscadoras a engranajes Figura 9 Roscado con la Roscadora a EngranajesAlmacenamiento de la máquina AccesoriosInstrucciones de mantenimiento Servicio y reparacionesDetección de averías Esquema de cableado 230 V con filtro en línea Diagrama de cableado 115/230Instalación de terminales en las escobillas Código de colores básico Código de colores europeoRidge Tool Company