Henny Penny OFG-390 manual GAS Leak Test, GAS Pressure, Regulator Setting

Page 19

Model OFG- 390

2-7. GAS LEAK TEST

Prior to turning the gas supply on, be sure the gas valve knob on the gas control valve is in the OFF position. The word “OFF” is at the bottom of the knob when the valve is closed.

Upon initial installation and after moving the unit, the pipings and fittings should be checked for gas leaks.Asimple checking method is to turn on the gas and brush all connections with a soap solution. If bubbles and occur, it indicates escaping gas. In this event, the piping connection must be redone.

	To avoid fire or explosion, never use a lighted match
	or open flame to test for gas leaks. Ignited gas could
	result in severe personal injury and/or property
	damage.
2-8. GAS PRESSURE	The gas pressure regulator on the gas control valve is
REGULATOR SETTING	factory set as follows:
	Natural: 3.5 inches water column (.87 kPa)
	Propane: 10.0 inches water column (2.49 kPa)
	The gas pressure regulator has been set by Henny Penny and
	is not to be adjusted by the user.

MAKE SURE GAS PRESSURE IS SET COR-

RECTLY. FAILURE TO DO SO CAN RESULT IN

SHORTENINGOVERFLOWINGTHE FRYPOT,

WHICH COULD CAUSE SERIOUS BURNS,

PERSONAL INJURY, FIRE AND/OR PROPERTY

DAMAGE.

703

2-9

Image 19

Contents OPERATOR’S Manual Page Limited Warranty for Henny Penny Equipment Keep appliance area free and clear from combustibles Datos Tecnicos Para Products CE Henny Penny Head GAS Open Fryer SpecificationsTable of Contents Proper Care IntroductionAssistance Injury SafetyHazardous Situation WHICH, if not AVOIDED, will Result in Death or SeriousPage Unpacking Instructions InstallationStrapped to the pallet, under the fryer Remove the counterweights from the pallet, which areUnpacking InstructionsOptional Ramp Unloading Model OFG 908 Ment. Restraining ties may be used for stabilization Position and install fryer to prevent tipping or moveSelecting LocationGAS Supply Ventilation of FryerSystem at test pressures equal to or less than 1/2 During any pressure testing of the gas supply pipingFryer must be isolated from the gas supply piping System by closing its individual manual shutoff valveModel OFG 303 GAS Leak Test Regulator SettingGAS Pressure Requirements ElectricalModel OFG Page Operation Operating Components Spark Ignitors Airflow SwitchHigh Limit Ignition ModulesMelt Cycle SwitchesIndicators LID OperationING is HOT and will Cause Burns Switches IndicatorsAlthough the Displaywillread Cool During the Standby MODE, the ShortenSMS Controls Filling or Adding Shortening Basic Operation Cool With Prolonged USE, the Flashpoint Care ShorteningWhich could Result in Serious Burns Personal INJURY, FIRE, AND/OR PropertyFiltering of Shortening Turn COOK/PUMP switch to OFF positionTube is not Tightened PROPERLY. if SO Cloth or Glove When TighteningSHORTENING, IT’S Possible That the Filter Connection AT the Union on the FilterLightingand Shutdown of the Burners Cleaning the Frypot PROTECTOR-MANUAL ResetRegular Maintenance Filter Pump MotorCleaning the Nylatrons Monthly Preventive MaintenanceLubricating Lid Rollers -Annually Maintenanc PreventiveCode ProgrammingAfter the proportional control, press and release Review Usage Special Program ModeReset Usage ProgrammingSpeaker Frequency, Codes, Initialize System Factory Presets F/C, Gas/Electric, Speaker VolumeAppliance Test Tech I/O ModeHeat Control Special ProgramMode Problem Cause Correction Troubleshooting Trouble Shooting GuideDisplay Cause Panel Board Correction Error Codes303 O S S a R Y Model OFG Shortening level also referred to as fill lines Gas fryers only See ignition modules Henny Penny Corp., Eaton, Ohio 45320, Revised