Henny Penny OFG-390 manual Programming, Code

Page 38

	Model OFG- 390
3-15. PROGRAMMING	1. Press and hold the FUNCTION button for two seconds.
	“REG PROGRAM” shows in the display, followed by
	“CODE”.

2.Press the code 1,2,3, “SELECT PRODUCT” scrolls across the display.

If no buttons are pressed, within approximately 1 minute while in the Program Mode, the controls will revert back to the Cook Mode.

3.Press the appropriate product button, (1-0), to identify what product you want to program.

4.“INT1” and “TIME” flashes on the left side of the display. The right side will show the starting time of the Cook Cycle and can be changed by pressing the appropriate numbers. Ex: Press 1,0,0,0 and 10:00 flashes on the right side of the display, setting the start time at 10 minutes.

5.After the time is set, press and release the FUNCTION button and “INT1” and “TEMP” flashes on the left side of the display. The right side will show the starting temperature and can be changed by pressing the appropriate numbers. Ex: Press 2,5,0 and “250° F” will show on the right side of the display, setting the start temperature at 250° Fahrenheit.

6.After the temperature is set, press and release the FUNCTION button and “INT1”, “LOAD”, and “COMP.” flashes on the left side of the display. The factory preset load compensation value shows in the right side of the display.

7.After the load compensation, press and release the FUNC- TION button. “PROP” and “CONTROL” shows on the left side of the display and the factory preset proportional control temperature shows on the right side of the display.

3-16

703

Image 38

Contents OPERATOR’S Manual Page Limited Warranty for Henny Penny Equipment Keep appliance area free and clear from combustibles Datos Tecnicos Para Products CE Specifications Henny Penny Head GAS Open FryerTable of Contents Assistance IntroductionProper Care AVOIDED, will Result in Death or Serious SafetyHazardous Situation WHICH, if not InjuryPage Installation Unpacking InstructionsInstructions Remove the counterweights from the pallet, which areUnpacking Strapped to the pallet, under the fryerOptional Ramp Unloading Model OFG 908 Location Position and install fryer to prevent tipping or moveSelecting Ment. Restraining ties may be used for stabilizationVentilation of Fryer GAS SupplySystem by closing its individual manual shutoff valve During any pressure testing of the gas supply pipingFryer must be isolated from the gas supply piping System at test pressures equal to or less than 1/2Model OFG 303 GAS Pressure Regulator SettingGAS Leak Test Electrical RequirementsModel OFG Page Operation Operating Components Ignition Modules Airflow SwitchHigh Limit Spark IgnitorsLID Operation SwitchesIndicators Melt CycleDuring the Standby MODE, the Shorten Switches IndicatorsAlthough the Displaywillread Cool ING is HOT and will Cause BurnsSMS Controls Filling or Adding Shortening Basic Operation Cool Personal INJURY, FIRE, AND/OR Property Care ShorteningWhich could Result in Serious Burns With Prolonged USE, the FlashpointTurn COOK/PUMP switch to OFF position Filtering of ShorteningConnection AT the Union on the Filter Cloth or Glove When TighteningSHORTENING, IT’S Possible That the Filter Tube is not Tightened PROPERLY. if SOLightingand Shutdown of the Burners Cleaning the Frypot Filter Pump Motor ResetRegular Maintenance PROTECTOR-MANUALLubricating Lid Rollers -Annually Preventive MaintenanceCleaning the Nylatrons Monthly Preventive MaintenancProgramming CodeAfter the proportional control, press and release Programming Special Program ModeReset Usage Review UsageFactory Presets F/C, Gas/Electric, Speaker Volume Speaker Frequency, Codes, Initialize SystemTech I/O Mode Appliance TestMode Special ProgramHeat Control Troubleshooting Trouble Shooting Guide Problem Cause CorrectionError Codes Display Cause Panel Board Correction303 O S S a R Y Model OFG Shortening level also referred to as fill lines Gas fryers only See ignition modules Henny Penny Corp., Eaton, Ohio 45320, Revised