Henny Penny OFG-390 manual Table of Contents

Page 7

TABLE OF CONTENTS

Section			Page
Section 1.	INTRODUCTION		1-1
	1-1	Introduction	1-1
	1-2	Proper Care	1-1
	1-3	Assistance	1-1
	1-4	Safety	1-2
Section 2.	INSTALLATION		2-1
	2-1	Introduction	2-1
	2-2	Unpacking	2-1
	2-3	Selecting the Fryer Location	2-4
	2-4	Leveling the Fryer	2-4
	2-5	Ventilation of Fryer	2-5
	2-6	Gas Supply	2-5
	2-7	Gas Leak Test	2-8
	2-8	Gas Pressure Regulator Setting	2-8
	2-9	Electrical Requirements	2-9
Section 3.	OPERATION		3-1
	3-1	Operating Components	3-1
	3-2	Lid Operation	3-3
	3-3	Melt Cycle Operation	3-3
	3-4	Switches and Indicators	3-3
	3-5	Filling orAdding Shortening	3-6
	3-6	Basic Operation	3-7
	3-7	Care of Shortening	3-9
	3-8	Filtering Instructions	3-9
	3-9	Changing the Filter Envelope	3-11
	3-10	Lighting and Shutdown of Burners	3-11
	3-11	Cleaning the Frypot	3-12
	3-12	Filter Pump Motor Protector-Manual Reset	3-13
	3-13	Regular Maintenance Schedule	3-13
	3-14	Preventive Maintenance	3-14
	3-15	Programming	3-16
	3-16	Special Program Mode	3-18
Section 4.	TROUBLESHOOTING		4-1
	4-1	Troubleshooting Guide	4-1
	4-2	Error Codes	4-2
GLOSSARY		.......................................................................................................................	G-1
Distributors List - Domestic and International

306

i

Image 7

Contents OPERATOR’S Manual Page Limited Warranty for Henny Penny Equipment Keep appliance area free and clear from combustibles Datos Tecnicos Para Products CE Henny Penny Head GAS Open Fryer SpecificationsTable of Contents Proper Care IntroductionAssistance Injury SafetyHazardous Situation WHICH, if not AVOIDED, will Result in Death or SeriousPage Unpacking Instructions InstallationStrapped to the pallet, under the fryer Remove the counterweights from the pallet, which areUnpacking InstructionsOptional Ramp Unloading Model OFG 908 Ment. Restraining ties may be used for stabilization Position and install fryer to prevent tipping or moveSelecting LocationGAS Supply Ventilation of FryerSystem at test pressures equal to or less than 1/2 During any pressure testing of the gas supply pipingFryer must be isolated from the gas supply piping System by closing its individual manual shutoff valveModel OFG 303 GAS Leak Test Regulator SettingGAS Pressure Requirements ElectricalModel OFG Page Operation Operating Components Spark Ignitors Airflow SwitchHigh Limit Ignition ModulesMelt Cycle SwitchesIndicators LID OperationING is HOT and will Cause Burns Switches IndicatorsAlthough the Displaywillread Cool During the Standby MODE, the ShortenSMS Controls Filling or Adding Shortening Basic Operation Cool With Prolonged USE, the Flashpoint Care ShorteningWhich could Result in Serious Burns Personal INJURY, FIRE, AND/OR PropertyFiltering of Shortening Turn COOK/PUMP switch to OFF positionTube is not Tightened PROPERLY. if SO Cloth or Glove When TighteningSHORTENING, IT’S Possible That the Filter Connection AT the Union on the FilterLightingand Shutdown of the Burners Cleaning the Frypot PROTECTOR-MANUAL ResetRegular Maintenance Filter Pump MotorCleaning the Nylatrons Monthly Preventive MaintenanceLubricating Lid Rollers -Annually Maintenanc PreventiveCode ProgrammingAfter the proportional control, press and release Review Usage Special Program ModeReset Usage ProgrammingSpeaker Frequency, Codes, Initialize System Factory Presets F/C, Gas/Electric, Speaker VolumeAppliance Test Tech I/O ModeHeat Control Special ProgramMode Problem Cause Correction Troubleshooting Trouble Shooting GuideDisplay Cause Panel Board Correction Error Codes303 O S S a R Y Model OFG Shortening level also referred to as fill lines Gas fryers only See ignition modules Henny Penny Corp., Eaton, Ohio 45320, Revised