Henny Penny OFG-390 manual Preventive Maintenance, Cleaning the Nylatrons Monthly

Page 36

3-14. PREVENTIVE MAINTENANCE

Dilution Box

3-14

Model OFG- 390

If moving fryer to perform preventive maintenance:

•Gas supply should be turned off to avoid fire or explosion.

•Electrical supply should be unplugged or wall circuit breaker turned off to avoid electrical shock.

Checking/Cleaning Dilution Box - Monthly

Cleaning the dilution box helps to ensure the unit operates efficiently and with few failures.

1.Make sure unit is off, and close and lock the lid.

Lid should be in locked down position. Failure to do so could result in personal injury.

2.Unscrew the wingnut on the lower left back access panel of the fryer, and remove access panel. Clean the dilution box with a cloth, or brush. Make sure the holes in the box are free of debris. Replace back shroud when finished.

Depending on the breading location and conditions within the kitchen area, the dilution box may need cleaned more often.

Cleaning the Nylatrons - Monthly

1.Spray Henny Penny biodegradable, food safe, foaming degreaser (part no. 12226) on Nylatrons.

2.Raise lid up and down several times to spread the degreaser.

3.Wipe Nylatrons to remove food soil, grease, and degreaser residue.

Lubricating Lid Rollers -Annually

The lid rollers, in the back of the fryer, should be lubricated at least once a year, to allow the lid easy movement.

1.Remove the back shroud of the fryer.

2.Using spindle lube, part number 12124, place a small amount of lube on both top and bottom rollers. Make sure to lube both left and right rollers.

810

Image 36

Contents OPERATOR’S Manual Page Limited Warranty for Henny Penny Equipment Keep appliance area free and clear from combustibles Datos Tecnicos Para Products CE Specifications Henny Penny Head GAS Open FryerTable of Contents Introduction Proper CareAssistance Safety Hazardous Situation WHICH, if notAVOIDED, will Result in Death or Serious InjuryPage Installation Unpacking InstructionsRemove the counterweights from the pallet, which are UnpackingInstructions Strapped to the pallet, under the fryerOptional Ramp Unloading Model OFG 908 Position and install fryer to prevent tipping or move SelectingLocation Ment. Restraining ties may be used for stabilizationVentilation of Fryer GAS SupplyDuring any pressure testing of the gas supply piping Fryer must be isolated from the gas supply pipingSystem by closing its individual manual shutoff valve System at test pressures equal to or less than 1/2Model OFG 303 Regulator Setting GAS Leak TestGAS Pressure Electrical RequirementsModel OFG Page Operation Operating Components Airflow Switch High LimitIgnition Modules Spark IgnitorsSwitches IndicatorsLID Operation Melt CycleSwitches Indicators Although the Displaywillread CoolDuring the Standby MODE, the Shorten ING is HOT and will Cause BurnsSMS Controls Filling or Adding Shortening Basic Operation Cool Care Shortening Which could Result in Serious BurnsPersonal INJURY, FIRE, AND/OR Property With Prolonged USE, the FlashpointTurn COOK/PUMP switch to OFF position Filtering of ShorteningCloth or Glove When Tightening SHORTENING, IT’S Possible That the FilterConnection AT the Union on the Filter Tube is not Tightened PROPERLY. if SOLightingand Shutdown of the Burners Cleaning the Frypot Reset Regular MaintenanceFilter Pump Motor PROTECTOR-MANUALPreventive Maintenance Cleaning the Nylatrons MonthlyLubricating Lid Rollers -Annually Preventive MaintenancProgramming CodeAfter the proportional control, press and release Special Program Mode Reset UsageProgramming Review UsageFactory Presets F/C, Gas/Electric, Speaker Volume Speaker Frequency, Codes, Initialize SystemTech I/O Mode Appliance TestSpecial Program Heat ControlMode Troubleshooting Trouble Shooting Guide Problem Cause CorrectionError Codes Display Cause Panel Board Correction303 O S S a R Y Model OFG Shortening level also referred to as fill lines Gas fryers only See ignition modules Henny Penny Corp., Eaton, Ohio 45320, Revised