Henny Penny OFG-390 manual Programming, Special Program Mode, Review Usage, Reset Usage

Page 40

Model OFG- 390

3-15. PROGRAMMING (Continued)

Another product can be programmed while in the program mode by following these procedures:

Press and hold the SCAN button at any time while in the Program Mode and the display will scroll “SELECT PROD- UCT”. Then press any of theproduct buttons, (1-0), and now that product can be programmed.

14.To program second interval, press and release the SCAN button while in the Time Mode of the first mode. “INT2” and “TIME” will flash on the left side of the display. Then follow the steps above, starting with step 4.

3-16. SPECIAL PROGRAM MODE

Review Usage

1.Press and hold the FUNCTION button for two seconds until “REG PROGRAM” shows in the display. As soon as “REG PROGRAM” shows in the display, press and release the FUNCTION button 1 time until “REVIEW USE” shows in the display.

2.“DAILY” shows in the display. Press any of the product buttons to view the usage of that product. Press and hold the FUNCTION button to exit Special Program mode.

Reset Usage

1.Press and hold the FUNCTION button for two seconds until “REG PROGRAM” shows in the display. As soon as “REG PROGRAM” shows in the display, press and release the FUNCTION button 2 times until “RESET USE” shows in display.

2.When “CODE” shows in the display, press 1-3-5. “DAILY will show in the display, and press any of the Product buttons to reset them to 0.

3-18

703

Image 40

Contents OPERATOR’S Manual Page Limited Warranty for Henny Penny Equipment Keep appliance area free and clear from combustibles Datos Tecnicos Para Products CE Specifications Henny Penny Head GAS Open FryerTable of Contents Proper Care IntroductionAssistance Safety Hazardous Situation WHICH, if notAVOIDED, will Result in Death or Serious InjuryPage Installation Unpacking InstructionsRemove the counterweights from the pallet, which are UnpackingInstructions Strapped to the pallet, under the fryerOptional Ramp Unloading Model OFG 908 Position and install fryer to prevent tipping or move SelectingLocation Ment. Restraining ties may be used for stabilizationVentilation of Fryer GAS SupplyDuring any pressure testing of the gas supply piping Fryer must be isolated from the gas supply pipingSystem by closing its individual manual shutoff valve System at test pressures equal to or less than 1/2Model OFG 303 GAS Leak Test Regulator SettingGAS Pressure Electrical RequirementsModel OFG Page Operation Operating Components Airflow Switch High LimitIgnition Modules Spark IgnitorsSwitches IndicatorsLID Operation Melt CycleSwitches Indicators Although the Displaywillread CoolDuring the Standby MODE, the Shorten ING is HOT and will Cause BurnsSMS Controls Filling or Adding Shortening Basic Operation Cool Care Shortening Which could Result in Serious BurnsPersonal INJURY, FIRE, AND/OR Property With Prolonged USE, the FlashpointTurn COOK/PUMP switch to OFF position Filtering of ShorteningCloth or Glove When Tightening SHORTENING, IT’S Possible That the FilterConnection AT the Union on the Filter Tube is not Tightened PROPERLY. if SOLightingand Shutdown of the Burners Cleaning the Frypot Reset Regular MaintenanceFilter Pump Motor PROTECTOR-MANUALCleaning the Nylatrons Monthly Preventive MaintenanceLubricating Lid Rollers -Annually Preventive MaintenancProgramming CodeAfter the proportional control, press and release Special Program Mode Reset UsageProgramming Review UsageFactory Presets F/C, Gas/Electric, Speaker Volume Speaker Frequency, Codes, Initialize SystemTech I/O Mode Appliance TestHeat Control Special ProgramMode Troubleshooting Trouble Shooting Guide Problem Cause CorrectionError Codes Display Cause Panel Board Correction303 O S S a R Y Model OFG Shortening level also referred to as fill lines Gas fryers only See ignition modules Henny Penny Corp., Eaton, Ohio 45320, Revised