Henny Penny OFG-390 manual Model OFG

Page 48

data plate

drain handle

drain interlock switch

drain valve

dumping table

fill lines

filter clips

filter drain pan filter envelope

filter heater switch filter pan dolly filter pump motor filter screen assembly

filter union

filter valve

flame sensors (gas fryers only)

fryer brush frypot

frypot collar

G-2

Model OFG- 390

a label or plate located on the right side panel of the fryer that indicates the fryer type, serial number, warranty date, and other information

the handle used to open and close the drain valve

a microswitch that automatically shuts off the fryer heat in the event the drain valve is inadvertently opened while the fryer power switch is in the ON position

a valve that allows the shortening to drain from the frypot into the filter drain pan; the fryer power switch should be in the OFF position before the drain valve is opened; the drain valve should remain closed at all other times

a table onto which the cooked product is dumped after removal from the fryer frypot

the four lines marked on the interior real wall of the frypot that show the proper shortening level (also referred to as level indictor lines)

the clips are the part of the filter screen assembly that holds the filter envelope closed

a pan that slides under the fryer into which shortening is drained

a fiber envelope into which the filter screen is placed; the end of the envelope is folded and held closed with filter clips; a part of the filter screen assembly

control panel switch that activates the strip heater (Model OE-100 only)

an optional transport cart for the filter drain pan

the motor that powers the filtering system

an assembly that filters the shortening as it is pumped from the frypot; the assembly is made up of two filter screens, a filter envelope, two filter clips, and a crumb catcher (Note: eight head fryers have two filter screens with no crumb catcher)

the threaded connection between the fryer and the filter system that can be connected or released without tools

the valve that must be opened to pump shortening back into the frypot during the filter cycle (Models OE-100, 320, and 340)

the sensors that shut off the gas supply to gas fryers if the pilot lights go out or do not light

a brush included with the fryer used to scrub the inside of the frypot

the interior portion of the fryer that holds the shortening and the product while cooking

the top flat surface area around the fryer lid

303

Page 47 Page 49
Image 48
Page 47 Page 49
Contents OPERATOR’S Manual Page Limited Warranty for Henny Penny Equipment Keep appliance area free and clear from combustibles Datos Tecnicos Para Products CE Specifications Henny Penny Head GAS Open FryerTable of Contents Introduction Proper CareAssistance Safety Hazardous Situation WHICH, if notAVOIDED, will Result in Death or Serious InjuryPage Installation Unpacking InstructionsRemove the counterweights from the pallet, which are UnpackingInstructions Strapped to the pallet, under the fryerOptional Ramp Unloading Model OFG 908 Position and install fryer to prevent tipping or move SelectingLocation Ment. Restraining ties may be used for stabilizationVentilation of Fryer GAS SupplyDuring any pressure testing of the gas supply piping Fryer must be isolated from the gas supply pipingSystem by closing its individual manual shutoff valve System at test pressures equal to or less than 1/2Model OFG 303 Regulator Setting GAS Leak TestGAS Pressure Electrical RequirementsModel OFG Page Operation Operating Components Airflow Switch High LimitIgnition Modules Spark IgnitorsSwitches IndicatorsLID Operation Melt CycleSwitches Indicators Although the Displaywillread CoolDuring the Standby MODE, the Shorten ING is HOT and will Cause BurnsSMS Controls Filling or Adding Shortening Basic Operation Cool Care Shortening Which could Result in Serious BurnsPersonal INJURY, FIRE, AND/OR Property With Prolonged USE, the FlashpointTurn COOK/PUMP switch to OFF position Filtering of ShorteningCloth or Glove When Tightening SHORTENING, IT’S Possible That the FilterConnection AT the Union on the Filter Tube is not Tightened PROPERLY. if SOLightingand Shutdown of the Burners Cleaning the Frypot Reset Regular MaintenanceFilter Pump Motor PROTECTOR-MANUALPreventive Maintenance Cleaning the Nylatrons MonthlyLubricating Lid Rollers -Annually Preventive MaintenancProgramming CodeAfter the proportional control, press and release Special Program Mode Reset UsageProgramming Review UsageFactory Presets F/C, Gas/Electric, Speaker Volume Speaker Frequency, Codes, Initialize SystemTech I/O Mode Appliance TestSpecial Program Heat ControlMode Troubleshooting Trouble Shooting Guide Problem Cause CorrectionError Codes Display Cause Panel Board Correction303 O S S a R Y Model OFG Shortening level also referred to as fill lines Gas fryers only See ignition modules Henny Penny Corp., Eaton, Ohio 45320, Revised
Top Page Image Contents